hit counter code
SAB Goblin 700 Manual
  1. Manuals
  2. Brands
  3. SAB Manuals
  4. Toy
  5. Goblin 700
  6. Manual

SAB Goblin 700 Manual

Kyle stacy edition
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
- Carefully check your model before
each flight to ensure it is airworthy.
- Consider flying only in areas
dedicated to the use of
model helicopters.
- Check and inspect the flying
area to ensure it is clear of
people orbstacles.
- Rotor blades can rotate at very
high speeds! Be aware of the
danger they pose.
- Always keep the model at a
safe distance from other pilots
and spectators.
- Avoid maneuvers with trajectories
towards a crowd.
- Always maintain a safe distance
from the model.
GOBLIN 700 KYLE STACY EDITION
SAB HELI DIVISION
SAB HELI DIVISION

Advertisement

Table of Contents
loading

Related Manuals for SAB Goblin 700

Summary of Contents for SAB Goblin 700

  • Page 1 GOBLIN 700 KYLE STACY EDITION - Carefully check your model before each flight to ensure it is airworthy. - Consider flying only in areas dedicated to the use of model helicopters. - Check and inspect the flying area to ensure it is clear of people orbstacles.
  • Page 2 Goblin 700 Kyle Stacy Edition Manual Release 1.0 - June 2015 WORLD DISTRIBUTION www.goblin-helicopter.com For sales inquiries, please email: sales@goblin-helicopter.com For info inquiries, please email: support@goblin-helicopter.com Attention: If you are a consumer and have questions or need of assistance, please contact in a first time the Goblin retailer where you made the purchase EUROPEAN DISTRIBUTION www.sabitaly.it...

  • Page 3: Very Important

    It is extremely important that you take a moment to register your helicopter with us. This is the only way to ensure that you are properly informed about changes to your kit, such as upgrades, retrofits and other important developments. SAB Heli Division cannot be held responsible for issues arising with your model and will not provide support unless you register your serial number.
  • Page 4 *Lack of care with assembly or maintenance can result in an unreliable and dangerous model. *Neither SAB Heli Division nor its agents have any control over the assembly, maintenance and use of this product. Therefore, no responsibility can be traced back to the manufacturer. You hereby agree to release SAB Heli Division from any responsibility or liability arising from the use of this product.
  • Page 5 Chapter 3, Components and Box TOOLS, LUBRICANTS, ADHESIVES ADDITIONAL COMPONENTS REQUIRED *Generic pliers *Electric Motor: 12S – 480/520Kv *Hexagonal driver, size 1.5,2,2.5,3,4mm Maximum diameter 64mm, *4mm T-Wrench Maximum height 64mm, *5.5mm Socket wrench (for M3 nuts) Pinion shaft diameter 6/8mm *8mm Hex fork wrench (for M5 nuts) *Speed controller: minimum 160A to be safe *Medium threadlocker (eg.
  • Page 6 Chapter 4, Carbon Frame The manufacturing process of the carbon parts often leaves micro-burrs and sharp edges. We recommend de-burring the edges to minimize 4-Carbon Frame the risks of electrical wire cuts, etc. Very important in red line zone. Page 4...
  • Page 7 Chapter 4, Carbon Frame BAG 1.1, FOAM 3, BOX 6 Socket Head Cap Screw M2.5x8mm (HC020-S) Stop Battery Plate (H0150-S) Battery Tray Flat Head Cap Screw (H0002-S) M2.5x5mm (HC128-S) Flat Head Cap Screw M2.5x5mm Frame Spacer (HC128-S) (H0003-S) Frame Spacer (H0003-S) Frame Spacer (H0003-S)
  • Page 8 Chapter 4, Carbon Frame BAG 1.2, BAG 1.3, FOAM 3 Note: Flat Head Cap Screw Frame Spacer M2.5x5mm (H0003-S) (HC128-S) ESC Support (H0088-S) Flat Head Cap Screw M2.5x5mm Frame Spacer (HC128-S) (H0003-S) Note: Canopy Positioners (H0159-S) Finishing Washer M3 (H0007-S) Cable Pass (HA010-S) Main Frame 1...
  • Page 9 Chapter 4, Carbon Frame BAG 1.2, BOX 6 Note: Choose the position for the batteries For the best 3D performance (with 12S-5000 batteries) Finishing Socket Head Cap we recommend position 1 Washer M3 Screw M3x10mm (H0007-S) (HC056-S) Bottom holes: 75mm max height batteries. Middle holes: 70mm max height batteries.
  • Page 10 Chapter 4, Carbon Frame BAG 2, BOX 7 Plastic Landing Gear Assembly Plastic landing gear F3C (H0449-S) [HC152-S] Metric Hex Landing Gear ROD Set Screws M4x4mm Nylon Nut M3 (H0431-S) (HC152-S) (HC206-S) Oring (HC453-S) Note: You can use Super Glue to lock Landing Gear Plug the nuts in correct position (H0432-S)
  • Page 11 Chapter 5, Transmission Assembly BAG 3, FOAM 1, FOAM 2 Flat Head Cap Screw M2.5x5mm (HC128-S) Bearing 24x6mm (HC426-S) Bearing Support Assembly (H0024-S) Socket Head Cap Screw M3x10mm Socket Head Cap (HC056-S) Screw M3x10mm (HC056-S) Servo Support (H0010-S) Column (H0018-S) Column (H0018-S) Bearing...
  • Page 12 Chapter 5, Transmission Assembly BAG 4, FOAM 2, FOAM 3 Note 1: 60T Pulley Assembly (H0171-S) When you tighten the collar (H0121-S) on the main shaft, ensure there is no axial play. Push down the main shaft while pulling up the Bearing locking collar.
  • Page 13 Chapter 5, Transmission Assembly BAG 5, FOAM 2 Tail Belt Idler Assembly (H0174-S) Flanged Bearing 7x3mm (HC402-S) Tail Belt Idler [H0069] Main Structure Assembly Belt Tensioner Arm Assembly (H0174-S) Button Head Cap Screw M3x4mm (HC038-S) Belt Tensioner Support (H0174-S) Spring Belt Tensioner de 8 / df0.5 / LL8 (HC315-S)
  • Page 14 Chapter 5, Transmission Assembly BAG 6, FOAM 1, FOAM 2 Socket Head Cap Screw M3x8mm (HC050-S) Flanged Bearing 13x5mm Bearing Support (H0143-S) (HC414-S) Lock H0142 after have locked the motor.Motor shaft is requires to optimize the centering. H0142 can't be used with motor shaft 8mm. 20T Pulley (H0175-20-S) Lock motor pulley after locking H0142...
  • Page 15 Chapter 6, Head BAG 7B, FOAM 3 Radius Arm Assembly ... x 2 Center Hub Assembly Socket Head Cap Screw M2.5x6mm (HC018-S) Flanged Bearing 7x3mm Radius Arm Center Hub (HC402-S) (H0421BL-S) (H0410BL-S) eg: Microlube GL261 Spindle Pin 5 mm (H0412-S) (H0413-S) Oring [HC176-S]...
  • Page 16 Chapter 7, Assembling The Modules BAG 8, FOAM 3 Head HPS3 Assembly Metric Hex Nylon Nut M4 (HC212-S) Socket Head Cap Socket Head Cap Screw M3x12mm Shoudered M4x24mm (HC062-S) (HC111-S) Swashplate Assembly Socket Head Cap Screw M3x8mm (HC050-S) Finishing Washer M3 (H0007-S) Carbon Frame Assembly...
  • Page 17 INSTALLATION OF SWASHPLATE SERVOS The linkage ball must be positioned between 17-19 mm out on the servo arm (figure 1), recommended servo arm SAB p/n [HA050/HA051]. The 120° placement of the servos inside Goblin means the arms are difficult to access. For this reason it is advisable to ensure alignment of the servo arms (and sub trim set) before installation of the servos in the model (figure 2).
  • Page 18 Chapter 8, Installation Of Swashplate Servos The wire for the front servo must be positioned here Head HPS Version Preliminary Setup Adjust the linkage as shown. The linkage Rod A has thead right/left. Turning, you can change the tracking without disconnecting the plastic ball link.
  • Page 19 H0175-20-S - 20T Pinion = ratio 10.7:1 H0175-24-S - 24T Pinion = ratio 8.9:1 H0175-21-S - 21T Pinion = ratio 10.2:1 H0175-25-S - 25T Pinion = ratio 8.6:1 Some example configurations: GOBLIN 700 KYLE STACY EDITION CONFIGURATIONS Rev:01 Battery Motor Pinion...
  • Page 20 Chapter 9, Installation Of The Motor FOAM 2 MOTOR BELT TENSION *Assemble the motor and pinion to its mounting plate. *Fit the motor assembly into position. *Compress the springs by pushing the motor toward the main shaft. *At maximum compression, temporarily tighten one of the slide screws. *With the minimum centre distance it is easy to install the belt.
  • Page 21 Chapter 10, Installation Of The ESC DE-BURR THE SIDE FRAMES We recommend de-burring the edges of the carbon parts in areas where electrical wires run. ESC INSTALLATION The speed controller (ESC) is installed in the front of the helicopter. Figure 1 shows the mounting area. Figure 2 shows the installation of the Kosmik ESC from Kontronik. You can also use the heat sink (H0165-S) if you wish for improved cooling (Figure 3,4,5) Figure 6: Shows the wiring which connects the receiver and ESC (in this picture one frame has been removed).
  • Page 22 Chapter 11, Installation Of Flybarless Unit and RX BAG 18 FLYBARLESS CONTROL UNIT AND RX INSTALLATION It is possible to install any commercially available Flybarless control unit in the goblin. For Flybarless systems with a separate sensor, the sensor must be installed under the plate (Figure 1). Figure 2 shows an example of installation of the receiver and flybarless control unit.
  • Page 23 Chapter 12, Tail System BAG 10B, FOAM 3 Tail Pitch Slider Assembly Tail Blade Grip Assembly ..x3 Bearing 10x4mm (HC411-S) Tail Blade Grip Flanged Bearing (H0327BL-S) 12x3.5mm (HC418-S) Bearing 10x4mm Tail Pitch Slider 01 (HC411-S) (H0409BL-S) Spacer 8.1x 9.2x3.2mm Socket Head Cap Screw M2x6mm Tail Pitch Slider 02 (HC004-S)
  • Page 24 Chapter 12, Tail BAG 11, BAG 12, FOAM 2, FOAM 3, BOX 6 Bell Crank Lever Assembly Tail Side Plate Assembly Bell Crank Base (H0058BL-S) Tail Upper Case (H0360-S) Washer 4x0.5mm Socket Head Cap (HC176-S) Tail Pin Tail Case Spacer Screw M3x8mm (H0264-S) (H0061BL-S)
  • Page 25 Chapter 12, Tail BAG 14 Tail Boom Assembly Yellow Carbon Tail Boom (H9045-S) DETAIL A Attaching H0082-S to the boom: Pre-assemble the two boom spacers H0082-S with the M3x20 socket set screw. Insert into the boom tube completely done up. Center the holes, then unscrew until there is contact with the walls Lock everything with the adhesive.
  • Page 26 Chapter 12, Tail BAG 13, BAG 16, BOX 3 Tail Boom Assembly Socket Head Cap Screw M3x12mm (HC062-S) Finishing Washer M3 (H0007-S) Socket Head Cap Screw M3x12mm (HC062-S) Finishing Washer M3 (H0007-S) Note: Before put plastic ball in threaded rod, please wait 12 hours after bonding Threaded Rod M2.5x40mm Threaded Rod M2.5x40mm (HC242-S)
  • Page 27 Chapter 12, Tail Servo Installation BAG 15 Tail Servo Assembly The distance between 15-16mm the axis and the ball must Uniball M2 be between 15-16 mm (H0064-S) Tail Servo Socket Head Cap Screw M2.5x12mm (HC026-S) Socket Head Cap Screw M2x6mm (HC004-S) Servo Spacer (H0075-S)
  • Page 28 Chapter 13, Installation Of The Boom BAG 17 BOOM ASSEMBLY *Insert the tail boom assembly . *Lock the M8 nuts with the HA016 special tool supplied. *Firmly lock the lateral srews M3x12mm. Use Loctile for this screw and make sure you remain tight. *Assemble the H0038 carbon security plate .
  • Page 29 Chapter 13, Installation Of The Boom, Canopy FOAM 3 TAIL BELT TENSION *Check the proper assembly of the tail boom. *Check that the aluminum part of the tube is against the M3 stop screw. *Loosen the tail group by loosening the 4 M3 screws. *Install the belt onto the pulley, taking care to respect the direction of rotation (figure 1).
  • Page 30 This helps The battery tray system in the Goblin 700 is simple, but very effective. increase the life of the strap. The battery should be attached to the tray (Part H0149) with heat shrink, tape or velcro.
  • Page 31 Chapter 15, In Flight BAG 20B, BAG 21 Always in Bag 21, you can take the KSE SERIAL NUMBER plate and put in this position In Bag 21, you will find the serial number tag for your Helicopter Sticking the tag as show. Please remember to register your product.
  • Page 32 Chapter 16, Maintenance ABOUT HPS3 The new HPS head offers an independent dampening system for each blade grip, there are three dampening settings: A = Soft for smooth response. B = Medium. C = Firm for direct and precise response. In the kit, there is the damper for direct and precise responce H0426-C Other Setting >>...
  • Page 33 Chapter 17, Exploded view, Carbon Frame Main Frame Name Specification Quantity Main Frame H0002 Battery Tray Carbon Fiber Name Specification Quantity H0003 Frame Spacers Aluminum H0432 Landing Gears Plug Plastic H0007 Finishing Washers M3 Aluminum H0449 Plastic Landing Gear F3C Plastic H0088 ESC Support...
  • Page 34 Chapter 17, Exploded view, Transmission Assembly TRANSMISSION ASSEMBLY Name Specification Quantity TRANSMISSION ASSEMBLY H0007 Finishing Washers M3 Aluminum Name Specification Quantity H0009 Main Structure Aluminum HC079 Socket Head Cap Screws M3 x 18mm H0010 Servo Support Aluminum HC091 Socket Head Cap Shoudered M4 x 40mm H0017 Swash plate Anti-Rotation Guide...
  • Page 35 Chapter 17, Exploded view, Head System Swashplate Set - H0420 Servo Assembly 1, 2, 3 Head System Quantity Head System Name Specification Quantity H0031 Uniball Spacers Aluminum Name Specification HC008 Head Cap Screws M2 x 8mm H0063 Uniballs M3x4 5 H18 HC018 Head Cap Screws M2.5x6mm...
  • Page 36 Chapter 17, Exploded view, Tail System TAIL SYSTEM Name Specification Quantity TAIL SYSTEM H0007 Finishing Washer M3 Aluminum Name Specification Quantity H0029 Spacer 8.1 x 9.2 x 3.2mm H0419 Tail Shaft Steel H0040 Tail Servo Locks Plastic H0435 Bushing Aluminum H0041 Locking Element Tails Carbon Fiber...
  • Page 37 Chapter 18, Spare Parts Battery Tray Frame Spacer Finishing Washer M3 Main Structure [H0002-S] [H0003-S] [H0007-S] [H0009-S] - 1 x CF Battery Tray. - 6 x Flat Head Cap Screws M2.5x5mm. - 3 x Frame Spacers. - 10 x Finishing Washers M3. - 1 x Main Structure.
  • Page 38 Chapter 18, Spare Parts Boom Spacer Plastic Ball Link Servo Spacer Washer 3.1x 12x1.8mm [H0066-S] [H0075-S] [H0078-S] [H0082-S] - 2 x Boom Spacer. - 10 x Plastic Ball Link. - 10 x Servo Spacers. - 4 x Washers 3.1x 12x1.8mm. - 1 x Set Screw M3x20mm.
  • Page 39 Chapter 18, Spare Parts Belt Tensioner Support 18T Pulley 19T Pulley [H0174-S] [H0175-18-S] [H0175-19-S] - 1 x Column Belt Tensioner. - 1 x Tail Belt Idler. - 1 x Belt Tensioner Arm. - 2 x Flanged Bearings 7x3mm. - 2 x Flanged Bearings 9x3mm.
  • Page 40 Chapter 18, Spare Parts Bell Crank Lever Tail Pitch Slider 3 Blade Center Hurb Spindle [H0406BL-S] [H0409BL-S] [H0410BL-S] [H0412-S] - 2 x Tail Pin. - 1 x Uniball M2. - 1 x Uniball Spacer. - 1 x Bell Crank Lever. - 2 x Flanged Bearing 7x3mm.
  • Page 41 Chapter 18, Spare Parts [HC002-S] [HC004-S] [HC008-S] [HC010-S] [HC018-S] [HC020-S] - 5 x Socket Head Cap -5 x Socket Head Cap -5 x Socket Head Cap -5 x Socket Head Cap - 5 x Socket Head Cap -5 x Socket Head Cap Screws M2x5mm.
  • Page 42 Chapter 18, Spare Parts [HC200-S] [HC206-S] [HC212-S] [HC218-S] - 10 x Metric Hex Nylon - 10 x Metric Hex Nylon - 10 x Metric Hex Nylon - 5 x Metric Hex Nylon Nuts M2,5H3,5. Nuts M3H4. Nuts M4H5. Nuts M5H4.5. [HC230-S] [HC232-S] [HC239-S]...
  • Page 43 - SAB HELI DIVISION Black Hoodies. SAB HELI DIVISION Neck Strap SAB HELI DIVISION Stand [HM034] [HM001,HM002,HM003] [HM038] - 1 x Neck Strap. - 1 x SAB HELI DIVISION CAP. - 1 x SAB HELI DIVISION Stand ( Set ). Page 41...

Table of Contents