Table of Contents
Advertisement
Operating Instructions
Color CCTV Camera
WV-CW590/G
Model No.
WV-CW594E
WV-CS580/G
WV-CS584E
WV-CW590/G
WV-CS580/G
WV-CW594E
WV-CS584E
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
The model number is abbreviated in some descriptions in this manual.
Advertisement
Table of Contents
Related Manuals for Panasonic WV-CW590G
Summary of Contents for Panasonic WV-CW590G
-
Page 1: Operating Instructions
Operating Instructions Color CCTV Camera WV-CW590/G Model No. WV-CW594E WV-CS580/G WV-CS584E WV-CW590/G WV-CS580/G WV-CW594E WV-CS584E Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. The model number is abbreviated in some descriptions in this manual. -
Page 2: Table Of Contents
CONTENTS Preface ..............3 RS485 setup . -
Page 3: Preface
Preface About the user manuals There are 2 sets of operating instructions for the WV-CW590/G, WV-CW594E, WV-CS580/G, WV-CS584E as follows. • Installation Guide: Explains how to install and connect devices. • Operating Instructions (PDF): Explains how to perform the settings and how to operate this camera. Adobe Reader is required to read these operating instructions (PDF) on the provided CD-ROM. -
Page 4: Rs485 Setup
RS485 setup The following procedure is to configure the RS485 4. Move the cursor to DATA BIT, and then tilt the setup when using the system controller to control the joystick left or right to select a data bit setting (7 or camera (pan, tilt, etc.) via the camera's data port. -
Page 5: About The Setup Menus
About the setup menus This manual describe procedures for operating system 3. Use the joystick to move the cursor the character controller WV-CU650. you want to input, and then press the CAM (SET) All setting configuration procedures start from the setup button. -
Page 6: Scene Select Settings
n Scene Select Settings n Preset Position Settings Display the scene select setting menu from the setup l Position Number Selection (MAP) menu to configure scene select settings. First, display the scene select setting menu. You could use the MAP item on the pan/tilt setup menu 1. - Page 7 • When using a system device other than the WV-CU650/ 2. Move the cursor to →PUSH SET to the right of PAN/ CU950*, WJ-HD309A/HD316A over 65 position TILT, and then press the CAM (SET) button to numbers cannot be set. (as of September 2005) display the PAN/TILT setting menu.
-
Page 8: Language Setting
3. Use the joystick to move the cursor the character you n Advanced Menu Settings want to input, and then press the CAM (SET) button. The advanced setup menu can be displayed from the The text input procedure is the same as that for setup menu. -
Page 9: Camera Settings
Camera settings n Using the Camera Setup Menu Loss of detail Wash out of Display the camera setup menu from the setup in dark areas bright areas menu (Advanced Menu) to configure camera settings (page 8). (page 8) 1. Display the advanced setup menu , move the cursor to CAMERA , and then press the CAM... - Page 10 Use the following steps to perform masking AUTO : This setting, by moving the shutter automatical- (1) Tilt the joystick up and down, and left and right ly when necessary, provides a clearer picture to move the cursor to a cell you want to mask. of extremely bright objects outdoors, etc.
- Page 11 Note: **ATW1** • The following are the differences between AUTO •••I•••0 and FIX. AUTO : Selecting X32 AUTO, for example, •••I•••0 automatically increases sensitivity, up to a maximum of 32 times. : S e l e c t i n g X 3 2 F I X , f o r e x a m p l e , RET TOP increases sensitivity 32 times.
- Page 12 2. If you selected AUTO in step 1, move the cursor to Note: LEVEL and then tilt the joystick left to select the • With some monitors and VTR models, output of a threshold illuminace level for switching between the camera images in the black and white mode will color mode and the black and white mode.
- Page 13 Notes: • If zoom limit is set to more than 36x, then zoom operation pauses at 36x magnification. • Increasing the zoom to over 36x magnification (digital zoom) decreases the resolution. • You cannot set a zoom magnification of greater than 36x as a preset position.
-
Page 14: Pan/Tilt Settings
Pan/tilt settings n Using the Pan/Tilt Setup Menu **PRESET POSITION** Display the pan/tilt setup menu from the setup menu to configure pan and tilt settings. First, display the pan/tilt setup menu. 1. Display the advanced setup menu (page 8), move the cursor to PAN/TILT , and then press the CAM 033-064... - Page 15 l Auto Focus (AF MODE) **SCENE FILE SHUTTER AUTO 1. Move the cursor to AF MODE, and then tilt the ON(MID) SENS UP joystick left or right to select an auto-focus function WHITE BAL ATW1 setting. MANUAL S.M.L : Auto focus does not operate after moving to a preset position.
- Page 16 3 Home Position Setting (HOME POSITION) Notes: A currently configured preset position can be • The HOME setting should be selected when you designated as the home position. want to normally leave the camera in the home Pressing the HOME button of the system controller will position and occasionally perform pan and tilt, or cause the camera to move to the currently specified when you want to activate SEQ.
- Page 17 4. Move the cursor to DWELL TIME, and then tilt the Notes: joystick left or right to select the start point and end • The auto mode is exited automatically whenever point dwell time setting. manual PAN/TILT or ZOOM/FOCUS is performed if Tilting the joystick cycles through the stop time AUTOPAN is operating and PAN/TILT does SEQ, display in the sequence shown below.
- Page 18 1(2MIN) ↔ 2(1MIN) ↔ 4(30S) Notes: • Selecting LEARN to teach the camera a patrol Note that the total patrol time is two minutes, and the routine causes the following parameters to be time allowed for each routine depends on the number stored along with the camera movements.
- Page 19 1. Move the cursor to PRIVACY ZONE, and then tilt the 7. Use the joystick to point the camera at the location to be masked, and then press the CAM (SET) button. joystick left or right to select a privacy zone setting. This registers the camera position and returns to ON (1) : Turns on the privacy zone function.
- Page 20 : Picture being picked up by the camera The direction indicators are N (north), NE (northeast), E (east), SE (southeast), S (south), SW (southwest), W continues to be displayed as the camera (west), and NW (northwest). moves to a preset position. 1.
- Page 21 5. Move the cursor to POSI , and then press the AREA TITLE 1 CAM (SET) button. 123456789 This will display the ID position setting menu. ABCDEFGHIJKLM NOPQRSTUVWXYZ 6. Use the joystick to select an area title display ().,'":;&#!?= +-*/%$ position, and then press the MON (ESC) button.
-
Page 22: Alarm Settings
Alarm settings n Using the Alarm Setup Menu l Configuring Detailed Motion Detector Settings for MOTION DET Display the alarm setup menu from the setup menu to configure alarm settings. 1. Move the cursor to MASK SET , and then press the CAM (SET) button. - Page 23 2 Preset Alarm Setting (PRESET ALM) Note: Turning on the preset alarm will output an alarm from • Size and speed limitations are relaxed somewhat the video output port or alarm output connector when when the contrast ratio between the background the camera completes a move to a preset position.
- Page 24 3. Move the cursor to ALARM IN 2, and then tilt the 6. Move the cursor to CNT-CLS 1, and then tilt the joystick left and right to select the operation the joystick left and right to select the alarm output that camera should perform when an external signal is should be performed over ALARM OUT 1 when an received by ALARM IN 2.
-
Page 25: Special Settings
Special settings n Using the Special Setup Menu The names and types of displays for the alarm display are shown in the table below. Display the special setup menu from the setup menu to adjust picture quality. Name of display Type of alarm First, display the special setup menu. - Page 26 (3) This returns to the PIX OFF menu. An asterisk (*) to the right of a PIX OFF number indicates that the number has a blemish compensation pattern assigned to it. ** PIX OFF ** 000 000 RET TOP To delete a blemish compensation pattern (1) On the PIX OFF menu screen, select of the pattern you want to delete, and press the CAM (SET) button.
-
Page 27: Password Settings
Password settings n Password Lock Settings Note: • The factory default password is 123. Set the password lock on the setup menu. 4. Press the CAM (SET) button. l Turning Password Lock ON and OFF This returns to the setup menu and toggles The password lock function can be used to allow only PASSWORD LOCK on or off. - Page 28 3. Move the cursor to NEW PASSWORD and press the CAM (SET) button to display the password setting menu. The password input screen will reappear if you press the CAM (SET) button after inputting the wrong password. If this happens, perform steps 2 and 3 again.
-
Page 29: Shortcuts
Shortcuts Shortcuts are supported when you are using the system controller that has a CAM FUNCTION button. With shortcuts, you can configure camera functions by inputting function codes on the 10-key pad and then pressing the CAM FUNCTION button. The following is a list of all of the shortcuts that are supported by this camera. In addition, you can also move the camera to a preset position by inputting the applicable position number on the 10-key pad. - Page 30 Controller Operation Setting [1] + [7] + [0] + [CAM FUNCTION] IRIS: CLOSE [1] + [7] + [1] + [CAM FUNCTION] SHUTTER: ON [1] + [7] + [2] + [CAM FUNCTION] SHUTTER: OFF [1] + [7] + [3] + [CAM FUNCTION] Increases shutter speed one step.
- Page 31 Importer's name and address to follow EU rules: Panasonic Testing Centre Panasonic Marketing Europe GmbH Winsbergring 15, 22525 Hamburg F.R.Germany © Panasonic System Networks Co., Ltd. 2011 sC1011-1101 3TR006805BZB Printed in China...