FILE NO. SERVICE MANUAL Multimedia Projector Model No. PLc-Xu111 U.S.A, Canada, Europe, U.K, Asia original Version chassis No. KM6-Xu11100 Match the Chassis No. on the unit's back cover with the Chassis No. in the Service Manual. If the Original Version Service Manual Chassis No. does not match the unit’s, additional Service Literature is re-...
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacture’s instructions. Replace Battery With SANYO Electric Co., Ltd., Part No. 645 089 8587 Only. Use of Another Battery May Present A Risk Of Fire or Explosion.
Specifications Mechanical Information Projector Type Multi-media Projector Dimensions (W x H x D) 13.15” x 3.07” x.9.13” (334 mm x 78 mm x 232 mm) (Not including adjustable feet) Net Weight 7 .7 lbs (3.5 kg) Feet Adjustment 0˚ to 9.0˚ Panel Resolution LCD Panel System 0.8” TFT Active Matrix type, 3 panels Panel Resolution 1,024 x 768 dots Number of Pixels 2,359,296 (1,024 x 768 x 3 panels) Signal Compatibility Color System PAL, SECAM, NTSC, NTSC4.43, PAL-M, and PAL-N High Definition TV Signal 480i, 480p, 575i, 575p, 720p, 1035i, and 1080i Scanning Frequency H-sync. 15 kHz–100 kHz, V-sync. 50–100 Hz Optical Information Projection Image Size (Diagonal) Adjustable from 33” to 300” Throw Distance 4.3’–32.8’ (1.3 m–10.0 m) Projection Lens F1.7–2.1 lens with f26.7 mm–32.0 mm with manual zoom and focus Projection Lamp 300 W Interface Video Input Jack RCA Type x 1 S-video Input Jack Mini DIN 4 pin x 1...
Circuit Protections This projector provides the following circuit protections to operate in safety. If the abnormality occurs inside the projec- tor, it will automatically turn off by operating one of the following protection circuits. Thermal switch There is the thermal switch (SW90) inside of the projector to detect the internal temperature rising abnormally.
Circuit Protections Warning temperature and power failure protection The projector will be automatically turned off when the internal temperature of the projector is abnormally high, or the cooling fans stop spinning, or the power supplies in the projector are failed. - If the WARNING indicator is flashing, it may detect the abnormal temperature inside the projector.
Maintenance Cleaning the Filter Filter prevents dust from accumulating on the optical elements inside the projector. Should the filter becomes clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat buildup and adversely affect the life of the projector. If a “Filter warning” icon appears on the screen, clean the filter immediately. Clean the filter by following the steps below.
Maintenance Lamp Replacement When the projection lamp of the projector reaches its end of life, top control the Lamp replacement icon appears on the screen and LAMP REPLACE indicator lights yellow. Replace the lamp with a new one promptly. The timing when the LAMP REPLACE indicator LAMP rePLAce should light is depending on the lamp mode.
Maintenance Resetting the Lamp Counter Be sure to reset the Lamp counter after the lamp is replaced. When the Lamp counter is reset, the LAMP RE- PLACE indicator stops lighting and the Lamp replacement icon disappears. Lamp counter Press the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons to move the red framed pointer to the Setting Menu icon.
Maintenance Cleaning After long periods of use, dust and other particles will accumulate on the LCD panel, prism, mirror, polarized glass, lens, etc., causing the picture to darken or color to blur. If this occurs, clean the inside of optical unit. Remove dust and other particles using air spray.
Security Function Notice Security Function Disable This projector provides security functions such as "Key lock", "PIN code lock" and "Logo PIN code lock". When the pro- jector has set these security function on, you are required to enter correct PIN code to use the projector. If you do not know the correct PIN code to the projector, the projector can no longer be operated or started.
Mechanical Disassembly Mechanical disassembly should be made following procedures in numerical or- Screws Expression der. (Type ) mm Diameter x Length Following steps show the basic procedures, therefore unnecessary step may T type M Type be ignored. Caution: The parts and screws should be placed exactly the same position as the original otherwise it may cause loss of performance and product safety.
Page 13
Mechanical Disassembly x Main, AV Board, Rear Panel and Fans Board removal 1. Remove the Main board. . Remove the Rear panel. 3. Remove AV board. 4. Remove fans (FN901, FN90). Main board Rear panel (T3x6)(Black)x (M.5x6)x5 AV board (M.5x6) (T3x6)x FN901 FN90...
Page 14
Mechanical Disassembly v Optical unit, MCI, Buzzer, Temp., Line Filter board,Fans removal 1. Remove the Optical unit. . Remove the MCI board. 3. Remove the Battery and Buzzer board. 3-1. Remove Screw (T3x8) and 4 hooks on the duct and then remove the Duct.
Page 15
Mechanical Disassembly b Power, Ballast, Lamp Cover Sw Board, Thermal Sw(SW902) removal 1. Remove the Power board. . Remove the Ballast board. 3. Remove the Lamp cover switch board and thermal switch (SW90). Isolation sheet ( sheet) (T3x6) Power board (T3x6)x Ballast board Lamp cover...
Optical Parts Disassembly Before taking this procedure, remove Cabinet Top , Cabinet Front and Main Board following to the “Mechanical Disas- sembly”. Disassembly requires a .0mm hex wrench. z Projection lens disassembly Note: The optical unit should be removed from the cabinet bottom before re- moving the projection lens.
Page 17
Optical Parts Disassembly c Relay lens disassembly (M.5x5)x Relay lens Ass'y Spring Relay lens Fig.3 v Polarized glass-in disassembly (M.5x5)x1 Polarized glass-in Ass'y Film sheet Polarized glass Hooks * Mount the polarized glass as the film at- tached side faces the Fig.4 prism side.
Page 18
Optical Parts Disassembly b LCD Panel/Prism Ass’y removal LCD Panel/ (M.5x4)x Prism Ass’y (M3x10) (Bottom side) Fig.5-1 IMPortANt NotIce on Lcd Panel/Prism Ass'y replacement LCD panels used for this model can not be replaced separately. Do not disassemble the LCD Panel/Prism Ass’y. These LCD panels are installed with precision at the factory.
Page 19
Optical Parts Disassembly Panel Type Check There are types of LCD Panel/Prism Ass'y for this model. Either L-Type or R-Type LCD Panel/Prism Ass'y is used on the projector. Check which type of LCD Panel/Prism Ass'y is used with the figure below. When replacing the LCD Panel/Prism Ass'y, you need to take "Panel Type Check and Setting"...
Page 20
Optical Parts Disassembly n Polarized glass, Pre-polarized glass removal * Mount the polarized glasses as the film attached side faces the LCD panel side. (Mx) (Green) Pre-Polarized Glass(G) Polarized Glass(G) (red) (Mx) Pre-Polarized Glass(B) Film Polarized Glass(R) Polarized Glass(B) Fig.6 (Blue) m Optical unit top removal 1.
Optical Parts Disassembly , Locations and Directions Parts Name When mounting or assembling the optical parts in the opti- cal unit, the parts must be mounted in the specified loca- Integrator lens (OUT) tion and direction as shown in figure below. Prism beam splitter (PBS) Condenser lens (OUT) Dichroic mirror (B)
Optical Adjustments Before taking optical adjustments below, remove the Cabinet Top following to the “Mechanical Disassembly”. Adjustments require a .0mm hex wrench and a slot screwdriver. When you adjust Integrator lens or Relay lens adjustment, you need to disconnect FPC cables of LCD panels on the main board. Optical adjustment requires a .0mm hex wrench and a slot screwdriver.
Optical Adjustments Integrator lens adjustment Turn the projector on by a state of without FPC cables. Project all of lights on the screen. Adjust the adjustment base of integrator lens assy to make color uniformity in white. 1) If the shading appears on the left or right of the screen as shown White Fig.2-1 , loosen 1 screw...
Optical Adjustments Relay lens-Out adjustment Turn the projector on by a state of without FPC cables. Project all of lights on the screen. Adjust the adjustment base of relay lens assy to make color unifor- mity in white. If the shading appears on the left or right of the screen as shown in White Fig.3 , loosen 1 screw...
Electrical Adjustments Service Adjustment Menu Operation to enter the service mode MeNu SeLect button To enter the “Service Mode”, press and hold the for more than 3 seconds. The service menu appears on the screen as follows. to adjust service data MeNu button SeLect button Select the adjustment group no.
Electrical Adjustments Circuit Adjustments CAUTION: The each circuit has been made by the fine adjustment at factory. Do not attempt to adjust the following adjustments except requiring the readjustments in servicing otherwise it may cause loss of performance and product safety. WArNING : uSe uV rAdIAtIoN eYe ANd SKIN ProtectIoN durING SerVIcING.
Page 28
Electrical Adjustments Gain adjustment [Pc] x Panel Type Check and Setting 1. Enter the service mode. * Before setting, you need to check which type of LCD pan- . Receive the 16-step grey scale computer signal with computer1 [rGB] el is placed on the projector according to the item "LCD mode.
Electrical Adjustments Gain adjustment [component] n Common Center adjustment 1. Enter the service mode. 1. Enter the service mode. . Receive the 16-step grey scale 480i-component signal computer2 [component] . Receive the 50%-Whole Gray computer signal with with mode. tP35G computer1 [rGB] mode.
Page 30
Electrical Adjustments . 50% White adjustment [Video] ⁄1 Keystone Offset adjustment 1. Enter the service mode. After replacing the G-sensor circuit (IC3851, IC180 . Receive the 16-step grey scale composite video sig- and peripheral circuit), readjust the Keystone Offset Video[Video] nal with mode.
Electrical Adjustments Service Adjustment Data Table These initial values are the reference data written from the CPU ROM to memory IC when replaced new memory IC. The adjustment items indicated with “✻” are required to readjust fol- lowing to the “Electrical adjustments”. Other items should be used with the initial data value.
Page 38
Electrical Adjustments Group/ Item Name Function Initial Range Note Item 7 ANGLE 2 COUNT 1 - 10 8 BLIND SECTOR 1 0 - 1024 9 BLIND SECTOR 3 0 - 1024 10 BLIND SECTOR BIAS 0 - 1024 Group 200 Option Logo Prohibition (0: Menu, 1: Forced, 2: 0 Logo Prohibition (Forced No Brand) 0 - 2...
Page 39
Electrical Adjustments Group/ Item Name Function Initial Range Note Item Luminance Level 5 Data for Dimmer: Dim 4 DIMMER_CTRL_LEVEL5 0 - 255 Level 5 at the less than the Value Luminance Level 6 Data for Dimmer: Dim 5 DIMMER_CTRL_LEVEL6 0 - 255 Level 6 at the less than the Value Luminance Level 7 Data for Dimmer: Dim 6 DIMMER_CTRL_LEVEL7...
Page 40
Electrical Adjustments Group/ Item Name Function Initial Range Note Item Temp. C-A to judge the Temp Error at Normal 14 Temp C-A Warning (Eco) 0-100 (Clogging Det.) 15 Temp A Warning Offset (Temp) 0-100 Offset of Temp Error (Temp.) Error Setting Value is increased XC at the 16 Temp B Warning Offset (Temp) 0-100 below condition...
Page 41
Electrical Adjustments Group/ Item Name Function Initial Range Note Item 2 Fan1 Speed Gain 0-255 3 Fan2 Speed Gain 0-255 Additional Fan Speed of Min at Lamp Voltage Down (unit: 0.1V) 4 Fan3 Speed Gain 0-255 5 Not used 9999 0-255 Group 257 Fan Dimmer Setting Dimmer Avarage measurement Time...
Page 42
Electrical Adjustments Group/ Item Name Function Initial Range Note Item 3 Fine Phase Do Phase Adj after Total Dot Adj. 0 - 1 0: Executes Fine Phase, 1: Not Execute 4 BLKDET Black Level Detection Area 0 - 3 0: Effective All Bit, 5 PHASEMSK Phase Detection Filter 0 - 3...
Page 43
Electrical Adjustments Group/ Item Name Function Initial Range Note Item 4 Disp Line 0 ~ 4095 Group 525 YCbCr (720P - 50 ) 0 Total Dots 1980 0 ~ 4095 * Read only 1 Disp Dots 1248 0 ~ 4095 2 H Back Porch 0 ~ 4095 3 V Back Porch...
Page 44
Electrical Adjustments Group/ Item Name Function Initial Range Note Item Group 545 RGB Video (720P - 50 ) 0 Total Dots 1980 0 ~ 4095 1 Disp Dots 1246 0 ~ 4095 2 H Back Porch 0 ~ 4095 3 V Back Porch 0 ~ 4095 4 Disp Line 0 ~ 4095...
Troubleshooting Indicators and Projector Condition Check the indicators for projector condition. Indicators LAMP Projector condition PoWer WArNING rePLAce red/green yellow The projector is off. (The AC power cord is unplugged.) The projector is preparing for stand-by or the projection lamp is being cooled down.
Troubleshooting No Power This projector provides a function which can be specified a defective area simply by indicating the LEDs. Connect the AC cord and press the Power button once and then check the LED indication. - When all of Led indicators are not lighting , the symptom indicates that the primary power supply circuit does not operate properly.
Troubleshooting No Picture Check following steps. No picture with all of input sources Check signal processing stage and LCD driving stage; Check RGB S&H signals at test points TP35B, TP35G, TP35R1. Check power supply circuit 15.5V and peripheral circuit. Check ICs IC501, IC531, IC561, IC501, IC531, IC561, IC401, IC301 and peripheral circuits.
Troubleshooting No Sound Check following steps. check if the audio sig- Check IC5001 and peripheral circuit. nal is observed at pins Check 5V_AUDIO, 9V power supply. 10 and 21 of Ic5001. check if the audio sig- Check IC5031, 5V_AUDIO and peripheral circuit. nal is observed at pins 5 Check the Mute signal at pin 1 of IC5031.
Control Port Functions Scaler I/O Port Functions (PW190) PIN NO. PORT NO. PORT NAME FUNCTION SIGNAL NAME DESCRIPTION PORTD7 DDC_SW3 DDC_SW3 DDC_SW3 VS_MCI V-Sync for MCI VS_MCI V-Sync. Input for MCI PORTC5 ON_3.3V 3.3V Power Drive, Power On: H PORTD6 DDC_SW1 DDC_SW1 DDC_SW1...
Control Port Functions PIN NO. PORT NO. PORT NAME FUNCTION SIGNAL NAME DESCRIPTION CR_IN CR_IN Compornent Video (CR) Input SCART_CV SCART_CV Composite Video Signal Input for SCART S-Y Signal Input Y_IN Y_IN Compornent Video (Y) Input SMUXIN1 SOG MUX input Ch1 Sync on Green Signal Input SMUXIN0 SOG MUX input Ch0...
Control Port Functions I/O Expander Port Functions (TE7783) PIN NO. NAME FUNCTION ACTION I/O_TXD0 For Alarm I/O_AN3 For Alarm I/O_ALART_OUT For Alarm R_AE18 W_R/C_SW L: Wired R/C CARD_IN WAKEUP WAKEUP REST X'TAL IN X'TAL OUT XSTDBYE XSTDBYEN MCI_ON H: MCI ON STANDBY_MCI H: MCI STANDBY POWER_ON_MCI...
Waveform VIdeo signal <VIdeo> HSYNc signal VSYNc signal HSYNc signal <tPdHS> VSYNc signal <tPdVS> r-S&H signal <tP35r> G-S&H signal <tP35G> B-S&H signal <tP35B> -61-...
KM6-XU11100 Electrical Parts List Product safety should be considered when a component replacement is made in any area of a projector. Components indicated by a mark in this parts list and the circuit diagram show components whose value have special significance to product safety.
KM6-XU11100 Electrical Parts List Electrical Parts List Note: Parts order must contain Chassis No., Part No., and Descriptions. Key No. Part No. description Key No. Part No. description 305 173 9618 TR 2SA1235A1E 305 173 9717 TR 2SA1235A1F ASSEMBLED BOARDS INTEGRATED CIRCUIT IC8301 309 644 2115...
Page 73
KM6-XU11100 Electrical Parts List Key No. Part No. description Key No. Part No. description 304 095 0809 CERAMIC 0.1U K 304 090 1108 CERAMIC 1000P K C8331 303 113 3818 CERAMIC 1000P K C8379 303 342 3313 CERAMIC 0.1U K 304 090 1108 CERAMIC 1000P K...
Page 74
KM6-XU11100 Electrical Parts List Key No. Part No. description Key No. Part No. description 304 090 1207 CERAMIC 0.01U K C8463 303 342 3313 CERAMIC 0.1U K 304 095 0809 CERAMIC 0.1U K C8534 303 155 4217 CERAMIC 15P J 304 094 7007 CERAMIC 15P J...
Page 75
KM6-XU11100 Electrical Parts List Key No. Part No. description Key No. Part No. description R8512 301 150 6014 MT-GLAZE 0.000 ZA 1/10W R8308 301 162 2219 MT-GLAZE 10 JA 1/10W R8309 301 162 2219 MT-GLAZE 10 JA 1/10W R8513 301 150 6014 MT-GLAZE 0.000 ZA 1/10W R8311...
KM6-XU11100 Mechanical Parts List Mechanical Parts List Note: Parts order must contain Chassis No., Part No., and Descriptions. Key No. Part No. description Key No. Part No. description CABINET PARTS 945 088 7902 DICHROIC MIRROR (B) 610 331 6413 ASSY,STAND LEG-KM6A 945 088 7919 DICHROIC MIRROR (G) 610 333 9276...
Page 108
SANYo electric co., Ltd. (KM6AC) May 007 DC 350 Printed in Japan...
Diagrams & Drawings Schematic Diagrams Printed Wiring Board Drawings Model Chassis No. PLC-XU111 KM6-XU11100 these schematic diagrams and printed wiring board drawings are part of the service manual original for chassis No. KM6-Xu11100, model PLc- Xu111. File with the service manual No. SM5110855-00...
KM6-XU11100 Parts description and reading in schematic diagram 1. The parts specification of resistors, capacitors and resistor reading coils are expressed in designated code. Please check Example 1/ D J 10K B the parts description by the following code table. .
Page 111
KM6-XU11100 Pin description of diode, transistor and IC ● diode ● transistor/Fet ● Ic...
Note on Soldering do not use solder containing lead. Solder This product has been manufactured using lead-free Use solder with the metal content and composition ratio solder in order to help preserve the environment. by weight given in the table below. Do not use solders Because of this, be sure to use lead-free solder which do not meet these conditions.
Page 121
Printed Wiring Board Diagrams ! cAutIoN LINe FILter ( SIde:A) LINe FILter (SIde:B) This projector is isolated from AC line by using the internal converter transformer. Please pay attention to the following notes in servicing 1. Do not touch the part on hot side (primary circuit) or both parts on hot and cold sides (secondary circuit) at the same time.