Read this manual prior to initial operation of the product! Dear Customer, We hope that your product, which has been manufactured in modern facilities and passed through a strict quality control procedure, will give you very good results. We advise you to read through this manual carefully before using your product and keep it for future reference. This User Manual will •...
Important safety information This section includes safety information that will help • Items soiled with cooking oils, acetone, alcohol, fuel protection from risks of personal injuries or materialistic oil, kerosene, stain remover, turpentine, paraffin and damages. Failure to follow these instructions shall cause paraffin removers must be washed in hot water with any warranty and reliability commitment to become void.
Compliance with the WEEE Directive and • Do not stop the dryer before the drying cycle comes to an end unless you will remove all laundry from the Disposing of the Waste Product: dryer fast in order to lay them and dissipate the heat. This product complies with EU WEEE •...
Installation Refer to the nearest Authorised Service Agent for installation of your product. Preparation of location and electrical installation for the product is under customer’s responsibility. Installation and electrical connections must be carried out by a qualified personnel. Prior to installation, visually check if the product has any defects on it.
Electrical connection Connecting the water drain hose; Connect the machine to a grounded outlet protected by a fuse of suitable capacity as stated in the technical specifications table. Our company shall not be liable for any damages that will arise when the machine is used on a circuit without grounding.
Technical specification Height (adjustable) 84.6 cm Width 59.5 cm Depth 59.8 cm Capacity (max.) 9 kg Weight (net) 39 kg Voltage Rated power input See type label Model code Type label is located behind the loading door. 7 EN...
Initial preparations for drying hings to be done for energy saving: A B C • Make sure that you operate the product at its full capacity but pay attention to not exceeding it. • Spin your laundry at the highest speed possible when washing them.
pads should not be dried in the dryer. Following weights are given as examples. • Do not use fabric softeners and anti-static products Approximate unless they are recommended by the manufacturers of Home articles weights (g) the fabric softener or the product. •...
Loading the laundry • Open the loading door. • Place the laundry in the machine without compressing. • Push the loading door to close. Ensure that no items are caught in the door. 10 EN...
Selecting a Programme and Operating Your Machine Control panel 6. Anti-creasing 1. Washing machine spin speed*/ Timer programme selection Prevents the laundry from creasing after the machine Spin speed used to spin the laundry in the washing completes its programme. macthine / Indicates the time for timer programs.
Time display •Wool Refresh You can use this function to ventilate and soften your The display shows the time remaining for the programme woolen laundry that can be washed in the washing to complete while a programme is running. Time machine.
Page 14
Programme selection and consumption table Programme table Approximate Spin speed in washing Drying time Programmes Capacity (kg) amount of remaining machine (rpm) (minutes) humidity Cottons / Coloreds Extra dry 1000 % 60 Cupboard dry 1000 % 60 Iron dry 1000 % 60 Xpress 35’...
Warning indicators Auxiliary function Audio Warning Warning indicators may differ according to the model of your machine. Filter cleaning Cancel Audio warning Audio warning Audio warning audio warning level 1 level 2 level 3 Your dryer will give an audio warning when the programme comes to an end.
Page 16
“Drying”: 1. Open the loading door and put the laundry in. 2. Set the drying programme and spin speed, and if - Lights up in all programmes apart from drying and required, select the auxiliary functions. ventilation. 3. Press “Time delaying” buttons “+” and “-” to set the “Iron Dry”: desired time delay.
Laundry may be added or taken out as much as desired during a drying process, but as this process will interrupt drying continuously, it will extend the program duration and increase energy consumption. Therefore, it is recommended to add laundry before the drying programme has started.
Maintenance and cleaning Filter Cartridge / Door Inner Surface Lint and fibres released from the laundry to the air during the drying cycle are collected in the “Filter Cartridge”. Sensor Such fibre and lint are generally formed during wearing and washing. Always clean the filter and the inner surfaces of the cover after each drying process.
Water tank; For the condenser; The moisture in the damp laundry is taken from the Hot and humid air in the condenser is cooled with the laundry and condens ed. Drain the water tank after each cold air from the room. Thus, the humid air circulating in drying cycle or during drying when “Water tank”...
Page 20
4. Clean the condenser by applying pressurized water with a shower armature and wait until the water drains. 5. Place the condenser in its housing. Fasten the 2 locks and make sure that they are seated securely. 6. Close the kick plate cover. 20 EN...
Suggested solutions for problems Drying process takes too much time • Meshes of the filter may be clogged. Wash with water. Laundry comes out wet at the end of drying. • Meshes of the filter may be clogged. Wash with water. •...