Alternatively, wear a discharging Wrist-strap device. (Be sure to remove it prior to applying power--this is an electric shock precaution.) Samsung Electronics...
Page 3
Always inspect for pinched, out- of-place, or frayed wiring. Do not change the spacing between components and the printed circuit board. Check the AC power cord for damage. Make sure that leads and components do not touch thermally hot parts. Samsung Electronics...
Page 4
3) Disassemble the deck. FPC into Main PCB CN1 (See Fig 1-2). 4) Disassemble the deck PCB. 5) Replace the Pick-up. Note : If the assembly and disassembly are not done in correct sequence, the Pick-up may be damaged. Fig. 1-2 Samsung Electronics...
Page 6
3. Product Specifications The specifications and design may be changed without notice. The weight and dimensions are approximate. MODEL DVD905 Power Requirements 120 Voltage, 60Hz Power Consumption Weight 4.4Kg Set Size (W)420mm x (D)339mm x (H)120mm Operating Temperature Range + 5 °C ~ 35 °C...
Page 8
2) Disassemble the door-tray ´ in direction of arrow. 3) Close Tray Œ and power off. Note : If Tray Œ doesnÕt open, insert a clip ˇ into the hole (as shown in detailed drawing), and open Tray Œ manually. Fig. 4-1 Samsung Electronics...
Page 9
4-1-2 Top cabinet 1. Remove 3 screws Œ on the back panel. 2. Remove 4 screws ´, ˇ on the left and right side. 3. Lift up the top cabinet in direction of arrow. CABINET-TOP 3SCREWS 2SCREWS 2SCREWS Fig. 4-2 Samsung Electronics...
Page 10
5. Remove 2 screws ˆ on the top of cover-panel assÕy 6. Remove 4 top hooks Ø and 5 bottom hooks ∏ and disassemble the cover-panel assÕy. 4 HOOKS 1 SCREW 2 SCREWS 2 SCREWS PCB-FRONT PANEL-FRONT ASS'Y 1 SCREW 5 HOOKS 2 SCREWS COVER-PANEL ASS'Y Fig. 4-3 Samsung Electronics...
Page 11
3. Remove 3 screws ˇ from PCB-SMPS. 4. Remove 3 Spacer-PCB ¨ inserted in PCB-SMPS and lift up PCB-SMPS. 5. Remove 2 screws ˆ to fix BRKT-PCB assÕy. 4 SCREWS PCB-MAIN BRKT-PCB ASS'Y 3 SCREWS HOLDER-PCB PCB-SMPS 2 SCREWS ASS'Y BOTTOM SPACER-PCB Fig. 4-4 Samsung Electronics...
Page 12
Disassembly and Reassembly 4-1-5 Deck, Frame-chassis 1. Remove 4 screws Œ from the deck and lift it up. 2. Remove 4 screws ´ from the frame-chassis and lift it up. 4 SCREWS DECK 4 SCREWS FRAME-CHASSIS Fig. 4-5 Samsung Electronics...
Page 15
3. Pull the tray ¨ to disassemble, while simultaneously pushing the hook ˆ, Ø in direction of arrow ÒAÓ, ÒBÓ. 2 SCREWS ASS'Y-DECK CLAMPER HOOK "A" "C" " B " HOOK GEAR-CAM CENTER TRAY EMERGENCY HOLE CLIP Fig. 4-8 Samsung Electronics...
Page 16
1. Remove 2 screws Œ and disassemble the assÕy-PCB deck ´. 2. Disassemble the assÕy-deck DVD ¨ in direction of arrow ÒBÓ, while simultaneously pushing the hook ˇ in direction of arrow ÒAÓ. ASS'Y-DECK DVD "B" "A" HOOK ASS'Y-PCB DECK 2 SCREWS Fig. 4-9 Samsung Electronics...
Page 17
15 15 SHAFT-SYNCHRO 14 14 15 15 GEAR-SYNCHRO 13 13 LEVER-OPEN S/W 12 12 1 SCREW ASS'Y-MOTOR LOAD 11 11 MOTOR,PULLEY ASSEMBLING : ADJUST THE END OF MOTOR SHAFT SAMELY AS HEIGHT OF PULLEY AT ASSEMBLY. Fig. 4-10 4-10 Samsung Electronics...
Page 18
Disassembly and Reassembly 4-3-4 Ass’y deck 1. Remove 4 screws Œ. 2. Lift up the assÕy-deck ´. 4 SCREWS ASS'Y-DECK Fig. 4-11 Samsung Electronics 4-11...
Page 20
Input : Common power to transformer(Vp) 20us Fig. 2-2 The output Vs of transformer is determined by the ratio of 1st Np and 2st Ns. Vs = (Ns/Np) x Vp Fig. 2-3 Vout Vout is output (DC) by diode and condensor. Fig. 2-4 Samsung Electronics...
Page 23
-8V rectified circuit -8V rectified voltage smoothing circuit circuit Power IN (85-265V) Fig. 2-14 2. PIC1(KA7552) internal block diagram Ð 10UA BIAS UVLD 2.8V Ð 7.0V 4.3k Ð 3.6V D MAX (46%, 70%) Ð 0.24V IS(+) Fig. 2-15 Samsung Electronics...
Page 24
3) Use the output of transformer as PIC1 Vcc : The loads are different before and after PIC1 driving. (Vcc of PIC1 decreases below OFF voltage, using only the resistance due to load increase after PIC1 driving.) - PR20 : For noise removal Samsung Electronics...
Page 25
- Connect PC14 to CS terminal and set the voltage charging time at initial voltage starting. SHUT OFF voltage - Increase the duty by raising the voltage gradually via PC14 at initial starting for normal operation. MAX DUTY voltage 2.3V (Duty max. is limited by F/B potential at initial starting) Samsung Electronics...
Page 26
Reverse sequence of the above description ® Duty down ® Vout down ® Maintain 5.8V (i.e., the feedback to maintains 5.8V). - PR35, PR36 : Reduce 5.8V overshoot - PR37, PC43 : Prevent IC3 oscillation(for phase correction) - PC18 : Adjust feedback response rate Samsung Electronics...
Page 27
- Shut OFF mode release : OS potential decreases below Time : 100ms / div 7V.(Charge OS terminal forcely) Volt : 5V / div - Feedback terminal open : Shut OFF (Refer to clause 5.); PC13A : For IS terminal input noise removal Fig. 2-19 Samsung Electronics...
Page 28
- Switch ON/OFF time : Releated to switch loss and noise 10. PIC1 overcurrent protection : PZD12 - Operate PZD12 and protect PIC1 from damage from residual overcurrent (PIC1 Vcc, due to external surge inflow and feedback line open). Samsung Electronics...
Page 29
(output from RFGC terminal of TC9420F, via low-pass filter to constitute a loop for adjustment of constant amplitude). The gain in EQout is 1.0 for DVD and 1.67 for CD. EQout terminal is connected with EQin(pin 45) externally, and inputs into DVD EQ and CD EQ(Waveform equalizing circuit). 2-10 Samsung Electronics...
Page 30
3) CLV control circuit to control the rotation rate of disc, 4) DIC5 Protection IC, connected with input/output of data processor, which releases the protection for the protected data (which is then transmitted to video decoder and Micom). Samsung Electronics 2-11...
Page 31
Protection IC is located between output of data processor and input of video decoder, (the next stage). it decodes the protected data after recognizing the key information read from disc and data status. If a disc violates the protection method, it stops the operation and reports to Micom. 2-12 Samsung Electronics...
Page 32
LC86P6232) of front and controls the devices on board to execute the corresponding commands after initializing the devices connected with micom on board at power on. Samsung Electronics 2-13...
Page 33
DVD PROCESSOR & NTSC/PAL CD PROCESSOR COPY RPOTECTION A/V DECORDER D/A CONVERTER ENOCDER DECODER FRONT MIC1 MICOM MICOM TMP93CS41F MIC4 74AC573 MIC6 ADDRESS DECODER DATA BUS MIC5 MIC2 MIC3 EPROM EPROM SRAM IS24C02 AM27C020 KM681000 MICOM BLOCK LOW ADDRESS HIGH ADDRESS...
Page 34
So to speak, the bus is used by time-division as shown in Fig 2-25, 26. Two and more devices can't be accessed simultaneously. ¥ CH1 : ALE (MIC4-11, Address Latch Enable Signal) ¥ CH2 : HAD0-7 (MIC4-2 to 9, Input data) ¥ CH3 : HA0-7 (MIC4-19 to 12, Output data) Fig. 2-24 Samsung Electronics 2-15...
Page 36
The basic operation repeats to perform disk data read --> memory full --> move pick-up to previous track --> disk data read --> memory full --> move pick-up to previous track as described above. Samsung Electronics 2-17...
Page 37
Reference Information 2-4-2 System control block diagram Fig. 2-27 2-18 Samsung Electronics...
Page 38
CH3 indicates a waveform that RF signal is cut by slice level and converted into digital data. ¥ CH1 : RFIN(DIC1-50, RF Input signal) ¥ CH2 : SLCO (DIC1-42, Slice level) ¥ CH3 : ED7 (DIC1-34, Sliced data of RF signal) Fig. 2-30 Samsung Electronics 2-19...
Page 40
Fig. 2-35 RLLD signal is ouputted at disk halt or occurrence of serious error. ¥ CH1 : RFIN(DIC1-50, RF Input signal) ¥ CH2 : RLLD (DIC1-38, RLLD at disk halt or occurrence of serious error) Fig. 2-36 Samsung Electronics 2-21...
Page 41
¥ CH1 : PVSREQ (DIC6-13, Data request signal from DVD1) ¥ CH2 : PVSACK (DIC6-14, Output data acknowledge signal) ¥ CH3 : BSTCLK (DIC6-17, Output clock) ¥ CH4 : PVSIN (DIC6-5 to 11, Output data) Fig. 2-39 2-22 Samsung Electronics...
Page 42
It shows the external memory refresh of DIC1 and uses Cas Before Ras Refresh. ¥ DIC2 (4MDRAM) REFRESH TIME Fig. 2-42 It shows refresh per approx. 31 usec as measurement of refresh waverform outputted by DIC1 in large timing. Refresh time(PERIOD) of DIC2(4MDRAM) Fig. 2-43 Samsung Electronics 2-23...
Page 44
When the tracking actuator inclines outwardly as the object lens follows the track during play, the SLED motor moves slightly (and counteracts the incline). 4. CLV SERVO (DISC Motor Control SERVO) Controls the disc motor to maintain a constant linear velocity (necessary for RF signal). Samsung Electronics 2-25...
Page 45
Reference Information 2-5-2 SERVO system block diagram Fig. 2-47 2-26 Samsung Electronics...
Page 46
SIC4. Pins 46, 49 of SIC7 are controlled by VREF(approx. 2.1V) during normal play. Meanwhile, DVD repeats the track jump from 1 to 4 in inner direction at normal play ( because data- read speed from disc is faster than data output speed on screen). Samsung Electronics 2-27...
Page 47
DIC1 pin 54 for constant linear velocity. 2. For DC, VCD mode Input RF signal (from Pick-up) to SIC7 pin 36, Detect SYNC signal from RF in SIC7, and output PWM signal to SIC7 pin 55 for constant linear velocity. 2-28 Samsung Electronics...
Page 50
STV0119 to rated output level. VR57 is load resistance demanded by STV0119 and the gain is determined by resistance ratio interfaced with collector and emitted of each transistor. VR51 VR50 Video output Video input VQ18 C1623 VR56/VR61 VR57 Fig. 2-52 Samsung Electronics 2-31...
Page 51
Y/C jack and RGB jack. These signals are abnormal and had better not to be outputted, seeing in RGB jack. It is same at RGB output. So, analog switch VIC32(14053) is used. output output Switch VIC32 14053 RGB/YC Fig. 2-54 RGB, Y/C switching 2-32 Samsung Electronics...
Page 52
2 CH L/R A IC3 5.1 CH DATA0 POST (PCM1720E) FILTER VIC1 FRONT L/R (LC6120P) DECODER AIC9 POST (PCM1720E) FILTER DATA1 REAR L/R POST AIC14 FILTER (PCM1723E) CENTER DATA2 +4.5dB -4.5dB AIC47(14053) WOOFER Fig. 2-55 Audio output block diagram Samsung Electronics 2-33...
Page 53
If only 2 speakers are used in spite of output to 5.1 channel, center/rear and subwoofer signal may be down mixed in 2 channel L/R. If there is a subwoofer speaker, it is outputted directly to subwoofer without down mixing. 2-34 Samsung Electronics...
Page 54
KIC3. Then, the switching of DVD audio output outputted from AIC3 and CD/VCD audio ouput of KIC3 at output in stereo 2 channels is describes in the below table. CD/VCD KIC5-9, 10 pin (A,B) Output KIC5-1, 13 Pin signal output KIC5-2, 12 Pin signal output Table 2-2 CD/DVD Ouput table Samsung Electronics 2-35...
Page 57
Reference Information 2-8-4 AIC3/AIC9 (PCM1720) DGND SCKI TEST LRCIN RSTB BCKIN ZERO AGND 2-8-5 AIC14 (PCM1723) SCKO GNDP GNDD MCKO LRCIN RSTB BCKIN ZERO VOUTR VOUTL GNDA 2-38 Samsung Electronics...
Page 58
PRE FIL Focus Error Detector C IN D IN TE OUT Vref V refIN V ref VREF & 2VR E IN V ref FIL Ripple Detector F IN 2V ref GEN. 2V ref FIL S/D sel TIME-CON. Samsung Electronics 2-39...
Check PR10 voltage is miss- ing? PQ(FET) D-S Check 2d voltage voltage is miss- ing? 6pin voltage Check PR11, 12, 13, 14 exists in PIC1? Replace PIC Pulse is missing Check feed back. in PIC1 5? Replace PQ1(FET) Samsung Electronics...
Page 63
Output voltage is miss- ing? PIC1 6 Check PR11, 12, 13, 14 voltage Output 10V error? No PIC1 5 output? PIC 8 Check PC14, 15 Output 7V error? Pattern check. PL36, PL37 Open check. PR21, 22, 23 PZD11, Open check Samsung Electronics...
Page 64
Thoubleshooting No power Front Micom FU1 of Check intermittent ON/OFF signal is miss- operation mode ing? PIC4, 6, 7 output is missing? Each output port open PIC4, 6, 7 input is OK? Replace the corre- sponding IC. Samsung Electronics...
Page 65
FIC3(FLT) pin ? Check S/W interface. Check Keys of STOP, PLAY, OPEN communication status with main Micom work normally? Check FR pins 34,13,12,11,10,8 7,6,26 If the problem persists: Check after replacing Front. Check other parts for normal Front operation Samsung Electronics...
Page 66
SIC2 3, 21 terminal? Replace uCOM program Actual velocity occurs at SIC2 18 terminal? Replace Hall PCB Check SIC2 peripheral circuit SLEDGS terminal is ÔLÕ (in search range)? Check SLEDGS terminal of uCOM. Check peripheral circuit. (Page5-6) Samsung Electronics...
Page 67
Check SIC2 peripheral soldering FINE SEEK check FINE SEEK RFRF signal is missing? Check RIC1 peripheral circuit RFCT follows center level of RFRF? Check PR11 peripheral circuit Track incoming is delayed? Time Out due to many jump counts (Page 5-11) Samsung Electronics...
Page 68
Check SIC7 53 peripheral circuit SIC4 14 ouput is normal? SLEDGS terminal is ÔLÕ? Check SQ1 peripheral circuit and SLEDGS terminal SIC4 17, 18 terminal outputs are normal? Check SIC4 soldering and power Pick-up transfer is smooth. Samsung Electronics...
Page 69
IC. Check path to SIC7 and DIC1 SIC6 Pin 1 output is normal? Check SIC6 soldering and power SIC5 Pin22 signal is normal? Check SIC5 soldering and power or Replace SIC5 Check or replace disc motor Samsung Electronics...
Page 70
No tray open/close MIC1 Pin84, 85 is OPEN:L.L? CLOSE:H.H Micom error Check SIC4 Pin26, 27 ouput at open/close Signal is reverse output (based on 4,5)? Check SR24, 25 peripheral circuit Check line state from SIC4 Pin26, 27 to tray motor Samsung Electronics...
Page 71
Thoubleshooting No disc LD is away from object lens at play key input? (Page 5-13) No disk focus incoming failure (Page 5-11) 5-10 Samsung Electronics...
Page 72
Check RR26, RR26A, RR28 value and A, B, C, D input FES in SIC7 43(TP39) is within specified range? Check RIC1 2, 3 peripheral circuit SIC4 1, 2 outputs are normal? Check SIC4 Check open state from SIC4 to Pick-up Samsung Electronics 5-11...
Page 73
Thoubleshooting No PICK-UP in Home position MIC1 8 Output is normal? Micom error SELED FG(MIC1 9) is input normally? Check SIC2, SIC9 signal transfer system Check SIC4 soldering and power 5-12 Samsung Electronics...
Page 74
180mV? RIC1 50 output is 0V? Divide RQ1 emitter terminal voltage and 5V real voltage difference into 12½ LD MPD error. Replace Pick-up Current exceeds 0.1A? Open check in related circuit LD out Pick-up replace Samsung Electronics 5-13...
Page 75
\ W R(MI C -29 pi n )/ R D(MI C 2-24 pi n ) si g nal s swi n g? Signals are output Replace DIC1 from DIC1-36, 37, 38 pin? DVD1 peripheral soldering and short check 5-14 Samsung Electronics...
Page 76
Common data bus line signal appears like CH2 of wave- form? Check short pin out of micomcommon- bus(8 bit)Check short or openingofmi- com Check solderingofmicom and com- CS2/RD/WR signals occur? munication devices Check DVD1 peripheral unit Play? Samsung Electronics 5-15...
Page 77
0V? MIC6-9, 10 pin is fixed Chekl DVD signal process block to 0V? MIC1-10 pin waveform Check MIC1 peripheral soldering state(0,1) changes whenever (Including 12MHz oscillationg of front micom) pressing front key? Check at front operation error 5-16 Samsung Electronics...
Page 78
VIC8, VIC9? (2, 5, 11, 14 pin) Normal data are out- Check DVC_SEL signal input put in VIC8, VIC9? in 1 pin (4, 7, 9, 12 pin) Check pin contact error of VIC1 (Check soldering and short) Samsung Electronics 5-17...
Page 79
VIC31? Check IREF, VREF, power of Video signal is output from VIC31? VIC31 Signal is output from amp? Check amp Normal analog signal is output from Check connection LPF? Check input/output of TR after LPF 5-18 Samsung Electronics...
Page 80
AIC32, 43-4 pin input is normal? Check AIC32, 34 peripheral cir- AIC32, 34-1 pin output is normal? cuit Base terminal level of AQ1, 2, 3, 4 are Check VCN11-14 pin mute "L"? Check AL3, 10, 36, 37 peripheral soldering and short Samsung Electronics 5-19...
Page 81
AIC37, 39-3 pin input is normal? cuit Check AIC37, 39 peripheral cir- AIC37, 39-1 pin output is normal? cuit Base terminal level of AQ7, 8, 9, 10 Check VCN11-14 pin mute are "L"? Check AL15, 20 peripheral soldering and short 5-20 Samsung Electronics...
Page 82
AIC401 pin output is normal? AIC41-3 pin input is normal? Check AIC40 peripheral circuit AIC41-1 pin output is normal? Check AIC41 peripheral circuit Check VCN11-14 pin mute Base terminal level of AQ713, 14 are "L"? Check AL28 peripheral soldering and short Samsung Electronics 5-21...
Page 83
AIC44-1 pin output is normal? AIC42-3 pin input is normal? Check AIC42 peripheral circuit AIC42-1 pin output is normal? Base terminal level of AQ16, 17 are Check VCN11-14 pin mute "L"? Check AL33 peripheral soldering and short 5-22 Samsung Electronics...