Related Manuals for Samsung PPM50H2
Summary of Contents for Samsung PPM50H2
- Page 1 Owner’s Instructions PPM50H2 Samsung Electronics America inc. 105 Challenger Road, Ridgefield Park, N.J. 07660-0511,U.S.A SERVICE DIVISION TEL: 1-800-SAMSUNG (1-800-726-7864) www.samsungsupport.com AA68-02166A(ENG)
-
Page 2: Important Safety Information
APPLIANCE TO RAIN OR MOISTURE. Thank You for Choosing Samsung Thank you for choosing Samsung! Your new Samsung product represents the latest in television technol- ogy. We designed it with easy-to-use on-screen menus and closed captioning capabilities, making it one of the best products in its class. We are proud to offer you a product that will provide convenient, dependable service and enjoyment for years to come. -
Page 3: Fcc Information
• The PDP can properly operate in less than temperature 32~104˚F and humidity 80%. Do not use in a hot and humid place. FCC Information User Instructions America QA Lab of Samsung 3351 Michelson Drive, Suite #290, The Federal Communications Commission Radio Irvine, CA 92612, U.S.A... -
Page 4: Table Of Contents
Be careful in the selection and duration of television formats used for viewing. Uneven PDP aging as a result of format selection and use,as well as other burned-in images,is not covered by your Samsung limited warranty. User Instructions... -
Page 5: Setup
Setup Your New Plasma Display Panel ...10 Remote Control Buttons ...12 Wall Installation Instructions ...14 Turning the PDP On and Off ...18... -
Page 6: Your New Plasma Display Panel
Your New Plasma Display Panel Front Panel POWER SOURCE, MENU, VOLUME (-,+), Remote Control Signal Receiver Press to turn SELECT ( , ), MUTE Aim the remote control towards the PDP on this spot on the Monitor. and off. Checking Parts Remote Control/ PC Cable Ferrite Cores (8EA) -
Page 7: Remote Control Buttons
” Aspect button Press to change the screen size. ’ Mode button Selects a target device to be controlled by the samsung remote control (ie., VCR, Cable, or DVD players). ˝ Clock Display button Press to display clock on the PDP screen. -
Page 8: Wall Installation Instructions
Wall Installation Instructions Installation Notes Do not install the PDP on any place other than vertical walls. To protect the performance of the PDP and prevent troubles, avoid the following. • Do not install next to smoke and fire detectors. •... - Page 9 Remove six large screws from the rear side of the display. Insert the bolts, dish-type washers, and insulation holder into the holes as shown in the following figure: Œ Bolt ´ Insulation holder Put the insulation rubber point protruding from the rear top of the display in the groove on the top of the wall attachment panel.
-
Page 10: Turning The Pdp On And Off
Turning the Monitor(PDP) On and Off Turning the Monitor(PDP) On and Off Press the Power button on the remote control. The PDP will be turned on and you will be ready to use it’s features. You can also use the Power button on the front of the PDP. -
Page 11: Connection
Connection (Connecting Speakers / Receiver) Connecting Speakers ...22 Connecting a VCR/Cable Box ...23 Connecting a DVD/Set-Top Box ...24... -
Page 12: Connecting Speakers
Connecting Speakers Speaker Audio Cable The speakers MUST have more than 7watts rating (impedance 8ohm). How to Connect Connect the speaker audio cable to the external speaker output jack on the rear of the PDP matching the “+” and “-” ends of the cable with the diagram on the PDP. Connecting PDP and Speakers / Stand and Speakers Fix the bracket onto the guide pole located on the rear of speaker and fasten the screws. -
Page 13: Connecting A Dvd/Set-Top Box
Connecting a DVD/Set-Top Box Power Plug Video (Y, P ) Cable Audio Cable How to Connect Connect a Video cable between the DVD/Set-Top Box (Y,P Top Box and the Component1/2 Video Input (Y,P ) Input jacks on the PDP. • You can attach the (supplied) to the both jacks of the Video cable. -
Page 14: Customizing The Picture
Customizing the Picture You can use the on-screen menus to change the Brightness, Contrast, Sharpness, Color, and Tint settings of your PDP. Press the Menu button, then press the joystick to enter. Move the joystick left or right to select the “Custom”. You will also see the items “Contrast”, “Brightness”, “Sharpness”, “Color”... -
Page 15: Viewing The Picture-In-Picture
Viewing the Picture-in-Picture Selecting the PIP Screen Press the Menu button. Move the joystick up or down to select the “PIP”, then press the joystick to enter. Quick way to access the PIP: Just press “PIP” on the remote control. Move the joystick left or right to select the “On”. -
Page 16: Changing The Screen Size
Changing the Location of the PIP Image Press the Menu button. Move the joystick up or down to select the “PIP”, then press the joystick to enter. Quick way to access the PIP location: Just press “Locate” on the remote control. Move the joystick up or down to select the “Locate”. -
Page 17: Freezing The Picture
Freezing the Picture Still Press the Still button on the remote control to freeze a mov- ing picture into a still one. Press again to cancel. Sound Control Customizing the Sound ...34 Using Automatic Sound Settings ...35 Using the Surround ...36... -
Page 18: Customizing The Sound
Customizing the Sound Press the Menu button. Move the joystick up or down to select the “AUDIO”, then press the joystick to enter. Move the joystick left or right to select the “Custom”. You will also see the items “Treble”, “Bass”, “Balance”... -
Page 19: Using The Surround
Using the Surround Press the Menu button. Move the joystick up or down to select the “AUDIO”, then press the joystick to enter. Move the joystick up or down to select the “Surround”, then move the joystick left or right to select the “Concert”, “Hall”... -
Page 20: Setting The Clock
Setting the Clock This PDP has a built-in clock that will appear on screen when you press the Clock Display button on the remote control. Setting this clock also allows you to use it to automatically turn the PDP On or Off. Press the Menu button. -
Page 21: Setting The Timers
Setting the Timers This PDP can be set to turn on or off automatically at specific times that you choose. Before using the timers, you must set the PDP’s clock, as described previously. Setting the On/Off Timer Press the Menu button. Move the joystick up or down to select the “TIME”, then press the joystick to enter. -
Page 22: Connecting Pc And Operation
Connecting PC and Operation Connecting to a PC ...44 Adjusting the PC Screen ...48 Changing the Position of the Image ...49 Changing the Size of the Image ...50 Enlarge of the Image (Zoom)...51 Move Expanded Picture ...52 Picture Quality Adjustment ...53 Information ...56 Power Saver (PC mode only)...57... -
Page 23: Connecting To A Pc
Connecting to a PC This PDP set is not compatible with Macintosh PC. Power Plug PC (15pin) Audio Cable Cable Cable Connecting a PC to the PDP Connect a PC (15pin) or BNC cable between the Video Output jack on the PC and the RGB1 (15p D-SUB) or RGB2 on the PDP. - Page 24 PC will probably be different, depending upon your particular version of Windows and your particular video card. But even if your actual screens look different, the same, basic set-up information will apply in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer. On the windows screen, select in the following...
-
Page 25: Adjusting The Pc Screen
Adjusting the PC Screen Adjusting the R.G.B Preset: • Press the RGB button to select the PC mode. Press the Menu button, then press the joystick to enter. Move the joystick up or down to select the “Color Control”, then move the joystick left or right to enter. Move the joystick up or down to select the item you want to change. -
Page 26: Changing The Size Of The Image
Changing the Size of the Image Preset: • Press the RGB button to select the PC mode. Press the Menu button. Move the joystick up or down to select the SETUP, then press the joystick to enter. Quick way to access the Size: Just press “Scaling”... -
Page 27: Move Expanded Picture
Move Expanded Picture Preset: • Press the RGB button to select the PC mode. Press the Menu button. Move the joystick up or down to select the SETUP, then press the joystick to enter. Quick way to access the Zoom: Just press “Zoom/Pan”... - Page 28 Frequency Adjustment Preset: • Press the RGB button to select the PC mode. Press the Menu button. Move the joystick up or down to select the SETUP, then press the joystick to enter. Move the joystick up or down to select the “Image Lock”, then move the joystick left or right to enter.
-
Page 29: Information
Information Preset: • Press the RGB button to select the PC mode. Press the Menu button. Move the joystick up or down to select the SETUP, then press the joystick to enter. Move the joystick up or down to select the “Miscel- laneous”, then move the joystick left or right to enter. -
Page 30: Function Description
Function Description Selecting a Menu Language ......60 Setting the Multi Control ....... .61 Using the Key Lock . -
Page 31: Selecting A Menu Language
Selecting a Menu Language Press the Menu button. Move the joystick up or down to select the “SETUP”, then press the joystick to enter. Move the joystick left or right to select the appropri- ate language: English, Spanish, or French. Press the Menu button to exit. -
Page 32: Using The Key Lock
Using the Key Lock When setting Key Lock ON, the buttons (SOURCE, MENU, VOLUME, SELECT, MUTE, POWER) on the front of the PDP don’t operate. But those buttons will operate when setting Key Lock OFF. Press the Menu button. Move the joystick up or down to select the “SETUP”, then press the joystick to enter. -
Page 33: Appendix
Remote Control Codes VCR Codes Cable Box Codes DVD Codes Appendix Troubleshooting...66 Care and Maintenance ...67 Specifications ...68... -
Page 34: Troubleshooting
Troubleshooting Before you call a service technician, please scan this list of problems and possible solutions. It may save you time and money. Problem Possible Solution Poor picture. Check all wire connections. The power indicator is amber The monitor is using its power management system. blinking. -
Page 35: Specifications
This is a Class A system so that it can be used in industrial areas. (Note: Class A system are for business use.) Model PPM50H2 Dimensions Display 1208.5 (W) X 89 (D) X 724 (H) mm ; 47.58 (W) X 3.50 (D) X 28.50 (H) inches Remote Control 54 (W) X 31.5 (D) X 220 (H) mm ;... - Page 36 Memo Memo...