Appliances), and Underwriters Laboratories (UL characteristics as the recommended replacement part Publication UL1410, 59.7). might create shock, fire and / or other hazards. Product safety is under review continuously and new instructions are issued whenever appropriate. SyncMaster 570BTFT / 580BTFT...
Page 3
Use only an anti-static solder removal device. Some brushing clothes together, or lifting your foot from solder removal devices not classified as “anti-static” a carpeted floor can generate enough static can generate electrical charges sufficient to damage electricity to damage an ESD. ESDs. SyncMaster 570BTFT / 580BTFT...
• Headphone: Max 50mW output (3.5-pi jack) • Speaker: Internal semi Dome (16ohm x 2) • SyncMaster 570BTFT/580BTFT complies with SWEDAC (MPR II) recommendations for reduced electromagnetic fields. • Designs and specifications are subject to change without prior notice. SyncMaster 570BTFT / 580BTFT...
Page 5
GND-B No Connection No Connection Not Used GND-Sync/Self Test GND-Sync/Self Test GND-Sync/Self Test DDC Data DDC Data DDC Data H-Sync H/V-Sync Not Used V-Sync Not Used Not Used DDC Clock DDC Clock DDC Clock 16 ~26 SyncMaster 570BTFT / 580BTFT...
Page 6
B : Horizontal sync width O : Frame time total P : Vertical sync width C : Back porch D : Active time Q : Back porch R : Active time E : Front porch S : Front porch SyncMaster 570BTFT / 580BTFT...
Page 7
B : Horizontal sync width O : Frame time total P : Vertical sync width C : Back porch D : Active time Q : Back porch R : Active time E : Front porch S : Front porch SyncMaster 570BTFT / 580BTFT...
3-1-3 Standard Stand Disassembly assembly. 2. Remove the 4 screws on the hinge assembly. 1. Remove 5 screws from the Stand Rear 3. Remove the 4 screws on the Stand Rear 2. Remove 4 screws from the Stand Bottom. SyncMaster 570BTFT / 580BTFT...
Page 9
Stand Bottom and the 4 screws on the four corner of the Stand Bottom. 8. Remove the 5 stopper hings from the Bracket Bottom. 9. Remove the Stand Base from the Stand Assembly. 3-2 Replacement Order of Lamp Assemblies - RN15MSS/RM15MOS (Samsung Panel) SyncMaster 570BTFT / 580BTFT...
Page 10
3 Disassembly and Reassembly SyncMaster 570BTFT / 580BTFT...
Page 11
Turn the LCD module over and put it on a flat desk set to the ground. 2. Push down the stopper and slide the lamp unit. 3. Please take out the lamp units from the LCD module. SyncMaster 570BTFT / 580BTFT...
Page 12
LCD module : opposite process 2 and 3 Replacement of lamp unit should be done at the power off state and rcommended clean bench condition. 3-4 Reassembly Reassembly procedures are in the reverse order of Disassembly procedures. SyncMaster 570BTFT / 580BTFT...
Does proper DC 12 V appear at Check SMPS PCB and CN816. DC jack connected to CN102? Does proper DC 5 V appear at Check FT100 and IC109. Pin 3 of IC109? Check IC401, IC111, Q101 and Q102. SyncMaster 570BTFT/580BTFT...
Page 15
2, 3, 54, 55 and 56 of IC301? Replace IC305 or check its related circuit. Replace IC310 and IC311 or Do the waveforms appear at check its related circuits. Pins 5 and 20 of CN301? Replace LCD Panel SyncMaster 570BTFT/580BTFT...
Page 17
CH1 RMS = 4.3 V 4-5 User Controls Don’t Work Does the DC level change at Check the buttons. Pins 11 and 12 of IC401 when you (SW861 ~ SW866) push the front panel button? Go to 4-4 No OSD Display. SyncMaster 570BTFT/580BTFT...
Page 18
Do the sound signals appear at Check IC803 and related circuits. Pins 3 and 14 of IC803? Does the DC 2.5 V bias appear at Check C815, CN813, R821, R822, Pin 16 of IC503? ZD803 on the Audio PCB. Check CN814, CN815 outputs. SyncMaster 570BTFT/580BTFT...
Page 19
Can you hear any sound from and related circuit R817, R820, the Headphones? ZD801, ZD802. Check the Headphone Plug in the Do you hear sound from the Headphone Jack and R821, R822, Internal Speaker? C815 on the Audio PCB. SyncMaster 570BTFT/580BTFT...