Chassis Model MJ15AS* 510N MJ15BS* 510T MJ17AS* 710N MJ17BS* 710T MJ19AS* 910N MJ19BS* 910T Manual CONTENTS 1. Precautions 2. Product Specifications 3. Disassembly & Reassembly 4. Alignments & Adjustments 5. Troubleshooting 6. Exploded View & Parts List 7. Electrical Parts List 8.
Page 2
❈ This Service Manual is a property of Samsung Electronics Co., Ltd. Any unauthorized use of Manual can be punished under applicable International and/or domestic law. Samsung Electronics Co.,Ltd. 416, Maetan-3Dong, Yeongtong-Gu, Suwon City, Kyungki-Do, Korea,443-742 Printed in Korea P/N : BN82-00087S-00 http://itself.sec.samsung.co.kr...
1 Precautions Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1 Safety Precautions 1-1-1 Warnings For continued safety, do not attempt to modify the circuit board. Disconnect the AC power and DC power jack before servicing.
1 Precautions 1-2 Servicing Precautions WARNING: An electrolytic capacitor installed with the wrong polarity might explode. Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions section of this manual. Note: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions.
2 Product Specifications 2-3 Pin Assignments Sync Type Separate Pin No. Green Blue DDC Return (GND) GND-R GND-G GND-B DDC Power Input (+5V) Self Raster Bi-Dr Data (SDA) H-Sync. V-Sync. DDC Clock (SCL) Sync Type Pin No. Rx2- Rx2+ No Connection No Connection DDC Clock (SCL) DDC Data (SDA)
2 Product Specifications 2-4 Timing Chart This section of the service manual describes the timing that the computer industry recognizes as standard for computer-generated video signals. Mode VGA2/ VGA3/ 70 Hz 60 Hz Timing 720 x 400 640 x 480 fH (kHz) 31.469 31.469...
3 Disassembly and Reassembly This section of the service manual describes the disassembly and reassembly procedures for the MJ15AS*/MJ17AS*/MJ19AS*/MJ15BS*/MJ17BS*/MJ19BS* TFT-LCD monitors. WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling these components. 3-1 Disassembly Cautions:1. Disconnect the monitor from the power source before disassembly. 2.
Page 10
3 Disassembly and Reassembly 3-2 Reassembly Reassembly procedures are in the reverse order of disassembly procedures. 6. Remove 7 screws, 4 hexa screws from the boards and lift up the boards. Caution : When repairing panel only, disconnect just LVDS cable, Panel-Lamp / Wire marked in circle in the picture without removing the screws on board in order to lift the board up.
4 Alignments and Adjustments This section of the service manual explains how to use the RS232 JIG. This function is needed for AD board change and program memory (IC110) change. 4-1 Required Equipment The following equipment is necessary for adjusting the monitor: •...
4 Alignments and Adjustments 4-6 Service Function Spec. 4-6-1 How to Display Service Function OSD 1. The value for brightness and contrast should be changed to zero. 2. Within 5 seconds, press the 3. Service function OSD will be displayed. ❇...
Page 13
4 Alignments and Adjustments 4-6-3 How to Control Service Function OSD •After change the panel or lamp, you must reset service function OSD. •The case of panel change After changeing the panel, press the menu key within 5 seconds,. Then, panel Ch. No increases one step and the panel time information is reset to zero. Simultaneously, other information is reset to zero (Upper/Lower lamp, Panel cycle).
Page 14
4 Alignments and Adjustments Memo MJ15AS*/MJ17AS*/MJ19AS*/ MJ15BS*/MJ17BS*/MJ19BS*...
5 Troubleshooting Notes: 1. Before troubleshooting, setup the PC’s display as below. • Resolution: 1024 x 768 • H-frequency: 61 kHz • V-frequency: 75 Hz 2. If no picture appears, make sure the power cord is correctly connected. 3. Check the following circuits. •...
Page 16
5 Troubleshooting Notes: 1. Before troubleshooting, setup the PC’s display as below. • Resolution: 1280 x 1024 • H-frequency: 64 kHz • V-frequency: 60 Hz 2. If no picture appears, make sure the power cord is correctly connected. 3. Check the following circuits. •...
Page 17
5 Troubleshooting 5-2-1 No Video (ANALOG) Check signal cable connection and power. X400 oscillate properly? Is there R, G, B input at R100, R101 and R103? Is there Hsync, Vsync waveform at Pin 100, 1 of IC 400? Is there Hsync, Vsync waveform at Pin 43, 44 of IC 200? Does the output signal appear at Pin 17~20, 22~27 of CN400?
5 Troubleshooting 5-2-2 No Video (DIGITAL) Check signal cable connection and power. X400 oscillate properly? Is there R, G, B input at R110, R112, R114, R111, R113 and R115? Is there waveform at R11, R117? Does the output signal appear at Pin 17~20, 22~27 of CN400? There are DC 5V at Pin 1, 2 and 3 of CN400?
Page 21
6 Exploded View and Parts List ❈ You can search for updated part codes through ITSELF web site. URL : http://itself. sec. samsung.co.kr 6-1 MJ15AS* MJ15AS*/MJ17AS*/MJ19AS*/ MJ15BS*/MJ17BS*/MJ19BS*...
7 Electrical Parts List ❈ You can search for updated part codes through ITSELF web site. URL : http://itself.sec.samsung.co.kr/ 7-1-1 MJ15AS* Main PCB Parts Level Loc. No. Code No. MJ15AS E27-MJ15AS BN94-00527D 0204-002420 CIS3 0204-002426 CIS4 3701-001219 CN101 3711-004712 CN600 6003-000117 IP/PCB+BRKT/PCB 6003-000117...
11 Schematic Diagrams ❈ This Document can not be used without Samsung’s authorization. Vcc_PANEL_IN 15" : +3.3V In 17"/19" : +5V In GOYA 2 M/M Only (Option) +14V_IN R600 AUDIO_EN C600 IC600 Q600 SUPLECODE 2SC2412K-Q D1 8 D1_1 R601 D2_1 R602 C603 1/16W...