Page 1 Home Page Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 1 JANUARY 2011 T A B L E C O N T E N T S INSTALLATION SECTION PART DESCRIPTION PAGE PRE-INSTALLATION INFORMATION SITE REQUIREMENTS .................... 1.1 GROUNDING CONDITIONS ................1.2 POWER CONDITIONS ...................
Page 2: Table Of Contents
Home Page Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 1 JANUARY 2011 CONNECTING STATIONS AND ADDITIONAL EQUIPMENT CONNECTING STATIONS ..................7.1 CONNECTING ADDITIONAL EQUIPMENT ........... 7.32 POWER UP PROCEDURES PRE-CHECK ......................8.1 STARTING THE SYSTEM ..................8.1 CHECKING THE FAN ..................... 8.2 NUMBERING EXTENSIONS AND C.O.
Page 3 Home Page Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 1 JANUARY 2011 Figure 3.14 Installing Interface Board into Slot Figure 3.15 Front Panel Lever Figure 3.16 Setting Switches and Jumpers on the TEPRI Figure 3.17 Setting Switches and Jumpers on the TEPRIa Figure 3.18 Front View of the TEPRI...
Page 4 Home Page Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 1 JANUARY 2011 Figure 3.48 Front View of the MGI64 Figure 3.49 Front View of the OAS Figure 3.50 SVMi-20E LED Indications Figure 3.51 VPM-E, VPMF-E and 8VPMF-E Combinations Figure 3.52 SVMi-20E/HD with no optional boards installed (LEFT) and SVMi-20E/CF with all...
Page 5 Home Page Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 1 JANUARY 2011 Figure 7.5 RJ-45 Port of the 16DLI2 (For Digital Phone) Figure 7.6 RJ-45 Port of the 8COMBO/8COMBO2 (For Digital Phone) Figure 7.7 LAN Connections Figure 7.8 Connecting a Door Phone and Door Lock Figure 7.9...
Page 6 Home Page Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 1 JANUARY 2011 Figure 7.41 DM Login Page Figure 7.42 OS Device Manager Client Application Open Screen Figure 7.43 Link Setup Figure 7.44 Site List Figure 7.45 MODEM Options Figure 7.46 Connect to an OS System Using Client App Method 1...
Page 7 TABLE 5.3: Rated Output in the Case of Operation with AC TABLE 5.4: Rated Output in the Case of Operation with DC TABLE 6.1: OfficeServ 7400 Line Conditions TABLE 7.1: Distance Between Stations and the System TABLE 7.2: DM Embedded Application Web Browser Requirements TABLE 7.3: Client Application PC Requirements...
Page 8  Do not install in close proximity to a fire sprinkler or other sources of water.  A dedicated commercial AC power outlet is required. Do not use extension cords.  Ensure that all wires and cables to and from the OfficeServ 7400 do not cross fluorescent lights or run in parallel with AC wires.
Page 9 The OfficeServ 7400 system requires that a supplementary earth ground be connected to the system. This is the preferred method of grounding the OfficeServ 7400. It should be noted that when the third wire ground becomes inferior, it many prevent the digital data bus from canceling out noise.
Page 10 Obviously, it is important to have a good source of ground connected to the OfficeServ 7400 system to drain this energy off. Again, a good earth ground source is required by the OfficeServ 7400 system.
Page 11: Table 1.1 Power Specifications
582.3W 1.4 UNPACKING AND INSPECTION The OfficeServ 7400 can be configured as a single cabinet, dual cabinet or 3-cabinet system. All OfficeServ 7400 cabinets are identical when shipped from Samsung. After unpacking the cabinet(s), inspect for signs of physical damage. If any damage is detected, do not attempt to install the system.
Page 12: System Installation Procedure
2.1 SYSTEM INSTALLATION PROCEDURE Installation Overview: 1) Install the OfficeServ 7400 cabinet on a table or inside a data rack depending on the installation environment. 2) Connect the ground to the ground lug behind the main cabinet.
Page 13: Figure 2.1 Tools Required For Rack Installation
Figure 2.1 Tools Required for Rack Installation 2.3.3 Installing in a Rack The procedure for installing the OfficeServ 7400 cabinet inside a 19-inch rack is as follows: 1) Attach the cabinet bracket to the bottom surface of the OfficeServ 7400 cabinet and fasten the bracket firmly with the three screws.
Page 14: Figure 2.3 Rack Installation
Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 2 MAY 2010 2) Attach the rack brackets to both sides of the rack and fasten the brackets firmly with the six screws. Figure 2.3 Rack Installation (2) 3) Align the cabinet to the guide rails of the rack and slide the cabinet into the rack.
Page 15: Figure 2.5 Rack Installation
Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 2 MAY 2010 4) Align the two holes of the cabinet bracket and the holes of the rack brackets and fasten the cabinet to the rack with the two screws.
Page 16: Figure 2.6 Grounding
INSTALLATION TECHNICAL MANUAL PART 2 MAY 2010 2.4 CONNECTING GROUND WIRES This section describes how to connect an external grounding wire to the OfficeServ 7400 system. External Grounding External grounding is required to prevent human injuries and system damage caused by lightning, static electricity, or voltage surge.
Page 17: Figure 3.1 Front Panel Configuration
This section describes how to install and replace various boards of the OfficeServ 7400 system. 3.1 CABINET CONFIGURATION The main and expansion cabinets of the OfficeServ 7400 system have 12 slots each. The slots are numbered 0~11 as shown below.
Page 18 The OfficeServ 7200 cabinet can be used as expansion cabinet 1 and/or expansion cabinet 2 for the OfficeServ 7400 system. Simply install an OS7200 LCP card in slot 0 of the cabinet and connect it to the MP40 via LCP link cable. The OS7200 cabinet cannot be used as a main cabinet for an OS7400 system.
Page 19: Figure 3.2 Possible Combination Of Os7200 And Os7400
Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 MAY 2010 Figure 3.2 Possible Combination of OS7200 and OS7400 The following table outlines the rules for card/slot compatibility and configuration: Table 3.1 Cards/Slot Compatibility Rules...
Page 20: Figure 3.3 Back Panel Components
Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 MAY 2010 IMPORTANT:  The OS7200 MCP/MP20, 4WLI and WIM module are NOT allowed in an OS7400 system.  Although the MGI64 and TEPRI2 can be installed in any universal slot of the OS7400 expansion cabinet, it is recommended that they be installed in the main cabinet in order to utilize the full capacity of the cards.
Page 21: Figure 3.4 Switch Settings
MP40 and LP40 boards. The OfficeServ 7400 MP40 (Main Control Processor) controls the system operation. The MP40 is required for all configurations and goes in slot 3 of the main cabinet. The LP40 goes in slot 0 of the main cabinet and each OS7400 expansion cabinet.
Page 22 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 MAY 2010  The system database is NOT stored in SRAM. The system database is now stored in the on- board NAND FLASH. This data can remain in NAND-FLASH until the system is defaulted.
Page 23: Figure 3.5 Installing The Processor Board
2) Align the MP40 board to the guardrails of the main cabinet slot 3, and slide the MP40 board into the slot. Figure 3.5 Installing the Processor Board (1) 3) Push the front panel lever until the board is completely inserted into the OfficeServ 7400 slot 3.
Page 24: Figure 3.6 Installing The Processor Board
4) The above steps 2~3 also apply to installing the LP40 board to slot 0 each cabinet. 3.2.3 Connecting MP40 Board to LP40 Board If the OfficeServ 7400 system consists of a main cabinet and up to two expansion cabinets, connect the MP40 board to each LP40 board located in the expansion cabinets using link cables.
Page 25: Figure 3.8 Connecting Mp40 Board To Lp40 Board
Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 MAY 2010 LP40 LINK1 LINK3 MISC1 LINK2 MISC2 LINK31 LINK32 LINK23 MP40 Figure 3.8 Connecting MP40 Board to LP40 Board LINK1 LINK3 LINK2...
Page 26: Figure 3.10 Front View Of The Mp40
MMC+ system software. The MMC+ contains 64MB of storage and the SD contains 1 Port for establishing the 10 Base-T/100 Base-Tx Ethernet connection Serial port (Samsung Engineering Use ONLY) Button for resetting the MP40 board RUN LED This LED indicates the status of the MP40...
Page 27: Figure 3.11 Front View Of The Lp40
Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 MAY 2010 Ports & LEDs Function Description LAN LED Status of LAN operation - Off: No-power and no-connection of LAN port - On: The color of the LED shows the LAN transmission speed and connection speed •...
Page 28 MIS daughterboard is installed Connection for OfficeServ 7150 PoE power supply Alarm port Port for connecting 10/100 Base-T LAN (reserved for future use) For internal Samsung engineering use only Button for resetting LP40 module RUN LED Indicates the status of the LP40...
Page 29 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 MAY 2010 3.2.6 Optional Daughterboards There are 5 types of optional daughtercards that can be installed ONLY on the LP40. Each optional daughtercard must be installed in specific positions of the LP40 (see Figure 3.9).
Page 30: Figure 3.12 Installing Optional Daughtercards On The Lp40
Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 MAY 2010 o Each SCM provides 12 additional conference circuits. (5 parties ea.) o You can install 2 SCMs per LP40; however, you can only 12 conference circuits from ONE of them.
Page 31: Figure 3.13 Installing Optional Modem Daughtercards On The Mp40
Interface boards can be installed in any universal slot according to the rules outlined in Table 3.1. Universal slots are slots 1, 2, and 4~11 in the main cabinet and slots 1~11 in the OfficeServ 7400 expansion cabinets. For OS7200 expansion cabinets, universal slots are slots 1~5.
Page 32 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 MAY 2010 Figure 3.14 Installing Interface Board into Slot 2) Push the front panel lever of the interface board until the board is completely inserted into the slot.
Page 33 TECHNICAL MANUAL PART 3 MAY 2010 3.3.2 Replacing Boards If the OfficeServ 7400 system fails to operate normally due to an error on the power supply board, control board, or interface board, replace the board with a new one. Removing Cables Replace a board after removing all cables connected to the board.
Page 34 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 MAY 2010 TEPRI Card Dip Switch Switch No. NFAS (24B) NFAS (23B + D) NETWORK* USER NORMAL *If this TEPRI/TEPRIa card is to be the master of a pair of TEPRI/TEPRIa cards that are used to connect two systems together via PRI networking, DIP switch 4 must be set to ON.
Page 35 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 MAY 2010 Figure 3.16 Setting Switches and Jumpers on the TEPRI JUMPER SETTING FOR TEPRI The TEPRI board comes from the factory with the following jumper settings. These settings should NOT be changed.
Page 36 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 MAY 2010 T1/E1 24B + D User (Slave) Network (Master) Figure 3.17 Setting Switches and Jumpers on the TEPRIa FRONT VIEW OF TEPRI BOARD The front view of the TEPRI board is shown in the picture below.
Page 37: Table 3.6 Ports And Leds Of The Tepri
Table 3.6 Ports and LEDs of the TEPRI Ports & LEDs Function Description T1/E1/PRI Ports that connect the T1/E1/PRI cable. Serial port (for Samsung Use ONLY) Button for resetting the TEPRI/TEPRIa board. SYNC LED Clock synchronization. - On: Indicates loss of framing (Error Condition).
Page 38: Table 3.7 Front Panel Components Of The Tepria
Function Description Port for connecting T1/E1/PRI cables Port for connecting to Ethernet (reserved for future use) Serial port for internal Samsung engineering use only. TP1 LED Indicates the type of the circuit connected to port P1. - On: PRI in operation...
Page 39 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 MAY 2010 TEPRI2 CARD The TEPRI2 card is a DUAL circuit digital trunk interface that supports either T1 or ISDN PRI service. It also supports Q-Sig/PRI signaling required for networking multiple systems. This card is functionally identical to the TEPRIa card, however, it offers two independent circuit interfaces labeled P1 and P2 on the front panel.
Page 40: Table 3.8 Setting Jumpers Of The Tepria
Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 MAY 2010 JUMPER SETTING  S2, dip switch #1 should be set to ON. This setting sets the entire TEPRI2 card into T1 mode.
Page 41: Table 3.9 Ports And Leds Of The 8Trk
Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 MAY 2010 3.3.4 8TRK The 8TRK board provides 8 ports for analog trunk lines with Caller ID capabilities. This board can go into any universal slot in any cabinet. Add as many as needed.
Page 42 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 MAY 2010 3.3.5 8TRK2 There are no LEDs on this board compared to the 8TRK card. FRONT VIEW OF 8TRK2 BOARD The front view of the 8TRK2 board is shown in the picture below.
Page 43: Table 3.10 Ports And Leds Of The 16Trk
There are no LEDs on this card. 3.3.7 16DLI2 This board provides 16 ports for connecting Samsung Digital Keysets. Each port provides 1B+D. This means only one station/one voice channel per port. This board can go into any universal slot of any cabinet. Add as many as needed.
Page 44: Table 3.12 Ports And Leds Of The 8Dli
TECHNICAL MANUAL PART 3 MAY 2010 3.3.8 8DLI This board provides 8 ports for connecting Samsung Digital Keysets. This board can go into any universal slot of any cabinet. Add as many as needed. SPECIFICATIONS The specifications of the 8DLI board are as follows: ...
Page 45 TECHNICAL MANUAL PART 3 MAY 2010 3.3.9 8COMBO/8COMBO2 This board provides 8 ports for connecting analog stations and 8 ports for connecting Samsung Digital Keysets. This board can go into any universal slot of any cabinet. Add as many as needed.
Page 46: Table 3.13 Ports And Leds Of The 16Sli2/16Mwsli
Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 MAY 2010 3.3.10 16SLI2/16MWSLI This board provides 16 ports for connecting analog stations. It can go into any universal slot of any cabinet. Add as many as needed. This card automatically detects DTMF or dial pulse signals from the SLT.
Page 47 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 MAY 2010  See Section 7.1.2 for port Pinout/Wiring.  Do not connect devices with a total REN greater than 5.0 to this card.
Page 48: Table 3.14 Ports And Leds Of The 8Sli/8Sli2
Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 MAY 2010 Front panel components of the 8SLI/8SLI2: Table 3.14 Ports and LEDs of the 8SLI/8SLI2 Ports & LEDs Function Description P1~P8 Station ports for analog phones.
Page 49 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 MAY 2010 Figure 3.33 Setting GWIM/GWIMT Jumpers 2) Align the connector of the optional security daughtercard (GWIMS) to that of the GWIM/GWIMT connector and firmly press the optional module downward.
Page 50: Table 3.15 Ports And Leds Of The Gwim/Gwimt
Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 MAY 2010 FRONT VIEW OF GWIM Figure 3.35a Front Panel View of the GWIM FRONT VIEW OF GWIMT Figure 3.35b Front Panel View of the GWIMT Table 3.15 Ports and LEDs of the GWIM/GWIMT...
Page 51 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 MAY 2010 Ports & LEDs Function Description RUN LED The status of the GWIM/GWIMT - Off: No power supplied or the operation in abnormal status - LED turns Green: Normal status V.35 LED...
Page 52 802.3af). This means that it can provide power to any IEEE 802.3af compliant device that is connected to any of its Ethernet ports. All Samsung ITP/SMT-i phones and SMT-R2000 Dual- Band APs can receive power when connected to the PLIM. When connected to the PLIM Ethernet port, these devices no longer need the AC power adapter.
Page 53 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 MAY 2010 PLEASE NOTE: The PLIM module uses the -48V rail from the OS7400 power supply to provide power to connected devices over Ethernet. The OS7400 power supply provides up to 6600mA of output current.
Page 54: Table 3.16 Ports And Leds Of The Plim
Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 MAY 2010 SPECIFICATIONS The PLIM/PLIM2 provides 16 ports of 10/100 Base-T. FRONT VIEW OF PLIM/PLIM2 The front view of the PLIM/PLIM2 is shown below.
Page 55: Table 3.17 Ports And Leds Of The Plim2
TX/SX/LX ports. The GPLIM can provide power to any IEEE 802.3af compliant device that is connected its Ethernet ports. All Samsung ITP/SMT-i phones and SMT-R2000 Dual-Band APs can receive power when connected to the GPLIM. When connected to the GPLIM Ethernet port, these devices no longer need the AC power adapter.
Page 56 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 MAY 2010 connected to GPLIM/GPLIMT/PLIM causes the total current draw per cabinet to exceed 6600mA. It does not provide power to DLI ports, MWSLI ports and other system interface cards.
Page 57 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 MAY 2010 FRONT VIEW OF GPLIM MODULE Figure 3.42 Front View of the GPLIM Table 3.18 Ports and LEDs of GPLIM Ports & LEDs...
Page 58 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 MAY 2010 3.3.15 GPLIMT The Gigabit PoE LAN Interface Module TX (GPLIMT) board provides data transmission through the intranet. Compared to the PLIM, the GPLIMT board comes with an additional GbE interface and can provide 12 10/100 Base-T interface ports and 2 1000 Base-TX ports.
Page 59: Table 3.19 Ports And Leds Of The Gplimt
Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 MAY 2010 The components on the front panel of the GPLIMT board have the functions below: Table 3.19 Ports and LEDs of the GPLIMT Ports &...
Page 60 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 MAY 2010 3.3.16 GSIM (Gigabit Switch Interface Module) The GSIM is a managed Layer 3 LAN switch. It offers ten (10) 1000 Base-SX/LX/TX interface ports and one SIO port.
Page 61: Table 3.20 Ports And Leds Of The Gsim
LED blinks when P1~P10 are on active status 3.3.17 MGI (MEDIA GATEWAY INTERFACE) The MGI board provides a variety of Voice over IP (VoIP) services for the OfficeServ 7400. This card is required for ITP/SMT-i phones, IP networking, IP trunking, SIP trunking and stations or any application that require VoIP.
Page 62 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 MAY 2010 MGI-D MGI-D MGI-D MGI-D Position 1 Position 2 Position 3 Position 4 Figure 3.46 Mounting Optional Board on MGI Board FRONT VIEW OF MGI BOARD The front view of the MGI board is shown in the picture below.
Page 63: Table 3.21 Ports And Leds Of The Mgi And Mgi-16
Table 3.21 Ports and LEDs of the MGI and MGI-16 Ports & LEDs Function Description Port that connects the Ethernet. Serial Port (for Samsung Use ONLY) Button for resetting the MGI/MGI-16. PWR LED This LED indicates the power supply status.
Page 64: Table 3.22 Mgi64 Front Panel Components
The MGI64 is a 64 channel Media Gateway Interface card. Just like the MGI, The MGI64 board provides a variety of Voice over IP (VoIP) services for the OfficeServ 7400. This card is required for ITP/SMT-i phones, IP networking, IP trunking or any application that require VoIP.
Page 65 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 MAY 2010 Ports & LEDs Function Description RUN LED This LED indicates MP40 status. - Off: Power is not being supplied. - On: Booting.
Page 66 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 APRIL 2011 3.3.19 OAS (OPTIONAL APPLICATION SERVICES) The OAS card is a 64 DSP Optional Application Services card. It contains 64 configurable DSP’s that can be used as MGI channels, MOBEX DTMF receivers (listed as MOBEX DSP in MMC 850) used by the Executive MOBEX feature, or a mix of both (determined by MMC 858).
Page 67 Table 3.23 OAS Front Panel Components Ports & LEDs Function Description Port that connects the Ethernet. Serial Port (for Samsung Use ONLY) Button for resetting the OAS. PWR LED This LED indicates the power supply status. - Off: Power is not being supplied.
Page 68 3.3.21 SVMi-20E The SVMi-20E card can be installed in the OfficeServ 7200 and OfficeServ 7400 Systems. This section provides the additional steps required to set up the SVMi-20E for operation in the OfficeServ 7400. Included is other basic information regarding components making up the SVMi-20E.
Page 69 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 MAY 2010  VM1 Status LED: This indicates that one or more of the embedded ports (port 1 thru 4) are off hook.
Page 70 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 MAY 2010 Embedded Ports 9 ~ 12 Ports 1 ~ 4 no SL2 connectors. connector Ports 1 ~ 4 No VPM provided. Ports 9 ~ 12 Slot 0 installed.
Page 71 3, 4, or 5 of the main cabinet.  OfficeServ 7400 SOFTWARE COMPATIBILITY: SVMi software version 5.3.3.5 or higher and OfficeServ 7400 MP software version 4.30 or higher are required to support more than 12 ports on the SVMi-20E card.
Page 72 The SVMi-20E card can be installed in any slot (1~5) of any cabinet. When configured for 20 ports, slots (3~5) of the main cabinet must be used. Check that the OfficeServ 7400 system’s power switch is in the OFF position. Next, position the SVMi-20E card in the grooves of the card guide and gently slide the card in until it makes contact with the connector.
Page 73 SYSTEM This section provides the additional steps required to set up the SVMi-20E card for operation in the OfficeServ 7400 system. Included here is information regarding the software set up for the phone system. After inserting the SVMi-20E card and turning the power on there are some important system options that should be set in order for the SVMi-20E to function correctly.
Page 74 SVMi-20E hardware. You are now ready to begin programming the SVMi-20E Voice Mail/Auto Attendant system parameters. See the SAMSUNG SVMi-20E Programming Manual. NOTE: See MMC references in the SVMi-20E Programming Overview documentation for other MMCs that interact with the SVMi-20E.
Page 75 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 JANUARY 2011 PROCEDURE THREE 1. From any phone on the system call one of the SVMi-20E ports or call the Bi-VMS station group (generally 5049).
Page 76 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 JANUARY 2011 CNF24 FRONT PANEL The front view of the CNF24 card is shown in the picture below. Figure 3.53 CNF24 LED Indications Table 3.25 CNF24 Front Panel Components...
Page 77 SYSTEM CAPACITY The CNF24 has 24 conference channels and a maximum of 4 cards can be installed on the OfficeServ 7400 system. The number of conference groups will increase when additional CNF24 cards are installed. When recording and/or paging features are used the number of conference members allowed to attend the conference is decreased since the recording and paging features occupy one conference channel each.
Page 78 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 JANUARY 2011 PORT ASSOCIATION Table 3.27 CNF24 Port Association The associated DB of DM Classified Port of for remote ports after Default Port...
Page 79 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 JANUARY 2011 Figure 3.55 CNF24 Parameter Settings 5. Enter the Service License key in DM 2.1.4 or MMC 860 for the CNF24 channels to become available.
Page 80 PART 3 JANUARY 2011 CNF24 LICENSE A license per channel is required to use the conference service. The maximum number of channels allowed per OfficeServ 7400 system is 96 (4 CNF24 cards x 24 channels). Figure 3.57 CNF24 License UPDATING CNF24 SETUP INFORMATION Each CNF24 card has a unique MAC address, and the OfficeServ system uses the MAC address to manage the card information.
Page 81 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 3 JANUARY 2011 CNF24 CARD STATUS The OfficeServ system provides conference services when the CNF24 card status is active. In the following cases the card status will change to idle: 1.
Page 82: Connecting Power Fail Transfer
1 on the 8SLI/8SLI2, 16SLI2, or 16MWSLI cards. In case the OfficeServ 7400 loses power from its AC source, and no battery backup is available, this feature is automatically activated. The analog telephone connected to port 1 of the SLI will get C.O.
Page 83: Connecting External Batteries
OfficeServ 7400 can also run without AC power on a -48VDC battery system or rectifier. There should be no more than a 0.5VDC drop in voltage from the OfficeServ 7400 and the batteries. Ensure polarity prior to connecting the external -48VDC power source to the system.
Page 84: Figure 4.1 Connecting An External
PROCEDURE FOR CONNECTING EXTERNAL BATTERY The procedure for using a battery cable to connect an external battery to the OfficeServ 7400 system is as follows: 1) Prepare the battery cable that was provided with the OfficeServ 7400 system. The battery cable consists of a red line and a blue line, and at the end of each line, GND (red line), - 48VDC (blue line) are labeled.
Page 85: Figure 4.2 Connecting An External
Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 4 MAY 2010 Connect Battery only to the BATTERY Connector socket on the back panel of the OS7400. DO NOT CONNECT BATTERY TO THE PoE INPUT CONNECTOR.
Page 86: Before Connecting Power
5.2 PROCEDURE FOR CONNECTING POWER SINGLE CABINET CONFIGURATION Use the AC power cable provided with the OfficeServ 7400 system to connect the input power terminal on the rear panel of the cabinet to a grounded outlet. Figure 5.1 Connecting Power (for Single Cabinet)
Page 87 A two-module system (7150 with 2 PoE-M PSU module) provides -54V, 15A. The GPLIM and PLIM/PLIM2 module uses the -48V rail from the OfficeServ 7400 power supply to provide power to the connected devices over ethernet. The OfficeServ 7400 power supply provides up to 6600mA of output current.
Page 88 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 5 MAY 2010 Table 5.1 Consumption Per Device Device Current Consumption CARD Name Type for Each Device (mA) 16DLI2 2-Line LCD Keyset Analog Phone...
Page 89 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 5 MAY 2010 Grounding Requirements  Follow all grounding conditions listed in Section 1.2.  The grounding wire of OfficeServ 7150 PoE PSU should not be connected to the conduit of the power cables in the building.
Page 90 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 5 MAY 2010 OFFICESERV 7150 FRONT VIEW Front view of the OfficeServ 7150 cabinet is as shown in the following illustration. The cabinet consists of two slots and one distributor. A PoE-M PSU module is inserted to each slot.
Page 91: Site Requirements
Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 5 MAY 2010 OFFICESERV 7150 INSTALLATION Electric Shock Make sure to turn this product OFF when servicing. Handling this product with AC power ON may cause electric shock.
Page 92: Grounding Conditions
Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 5 MAY 2010 GROUNDING CONDITIONS Observe the following requirements when OfficeServ 7150 PoE is grounded.  The grounding wire of OfficeServ 7150 PoE shall be connected to the ground through a qualified grounding media.
Page 93 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 5 MAY 2010 INSTALLATION PROCEDURE This section describes how to install OfficeServ 7150 PoE on the floor or inside a rack. Select an Installation Method OfficeServ 7150 may be installed either on the floor or inside a 19 inch rack.
Page 94: Figure 5.6 Installation In A
Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 5 MAY 2010 Figure 5.5 Tools Needed for Installation in a Rack 1) Attach the cross bar bracket to the bottom of OfficeServ 7150 PoE, and tighten with three screws.
Page 95: Figure 5.7 Installation In A
Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 5 MAY 2010 2) Attach the rack mount brackets to both sides of the rack, and tighten with six screws. Figure 5.7 Installation in a Rack (2) 3) Guide the OS7150 unit through the guide rails formed by the rack mount brackets.
Page 96: Figure 5.9 Installation In A
Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 5 MAY 2010 4) Match the cross bar bracket attached to the 7150 to the two holes in the bracket inside the rack properly and then tighten with screws.
Page 97  Disconnect and turn off all power to the 7150 before connecting the battery.  Disconnect any connections to an OfficeServ 7400 system.  Pay attention to polarity (+,-) orientation of the battery when connecting to the system. 1) A battery cable comes with the OfficeServ 7150 cabinet. One end of the battery cable is a green keyed plastic connector.
Page 98 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 5 MAY 2010 Figure 5.11 Connecting an External Battery Safety Tips in Connecting External Battery Cable As OfficeServ 7150 is a high output power supply system, maximum of DC48V 30A may be flown from the battery.
Page 99 -54V lug from the left on the back of the OfficeServ 7150. 4) If connection to a second OfficeServ 7400 cabinet is required, then repeat the steps above and connect the red wire to the 2 GND lug from the left and the blue wire to the second +54V lug from the left.
Page 100 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 5 MAY 2010 Figure 5.13 PoE Cable OfficeServ 7150 Red Line Blue Line Socket for External Battery OfficeServ 7400 Figure 5.14 Connecting OS7150 to OS7400...
Page 101 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 5 MAY 2010 Rated Output Table 5.3 Rated Output in the Case of Operation with AC Rated Output in the Case of Operation with AC 1 Module DC -54V, 7.5A...
Page 102: Safety Precautions
TECHNICAL MANUAL PART 6 MAY 2010 PART 6. CONNECTING C.O. LINES This section describes how to connect C.O. lines to the OfficeServ 7400 system after installation. 6.1 SAFETY PRECAUTIONS To reduce the risk of personal injury, follow these precautions before connecting TELCO circuits: ...
Page 103: Connecting C.o. Lines
TEPRI/TEPRIa/TEPRI2 boards can be connected to a T1/E1 C.O. circuit through a RJ-45 port. As show below, connect a T1/PRI circuit to the T1/E1/PRI port of the OfficeServ 7400 system. Though the TEPRI board supports E1, it is not used in the USA.
Page 104 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 6 MAY 2010 ORDERING A T1 The following information may be useful when ordering T1 service from the telephone company. PARAMETERS supported on OfficeServ all TEPRI cards...
Page 105: Connecting Stations And Additional Equipment
Maximum 400m/1312ft (for AWG #24) Analog phone Maximum 1km/3280ft (for AWG #24) Door phone Maximum 400m/1312ft (for AWG #24) AOM (Add-On Module) Maximum 400m/1312ft (for AWG #24) NOTE: If you are connecting Samsung DCS keysets, the keyset version must be 1.2 or higher.
Page 106 7.1.2 Connecting an Analog Phone Connect an analog phone to the 8SLI/8SLI2, 16SLI2, 16MWSLI, 8COMBO/8COMBO2 board installed in the OfficeServ 7400 system. CONNECTING TO THE 8SLI/8SLI2 Connect an analog phone to the 8SLI/8SLI2 board by using a twisted pair of AWG #24 or AWG #26 wire.
Page 107 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 MAY 2010 CONNECTING TO THE 8COMBO/8OMBO2 Connect an analog phone to the 8COMBO/8COMBO2 board by using a twisted pair of AWG #24 S1~S8...
Page 108 CAUTION: The input power of the SMT-i Series phones needs 5.0vDC and 3000mA. The SMT-i5210, SMT- i5220, SMT-i5230, and SMT-i5243 need to be powered by using Samsung’s SMT-A53PW power adapter. The SMT-i3105 requires the SMT-A53PA power adapter. Failure to use the appropriate power supply will cause permanent damage to the phone and will void Samsung’s warranty.
Page 109 Refer to the SMT-R200 AP documentation for wireless LAN installation information. 7.1.8 Connecting a Door Phone and a Door Lock Connect a door phone and a door lock to the OfficeServ 7400 system using a Door Phone Interface Module (DPIM).
Page 110 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 MAY 2010 Figure 7.8 Connecting a Door Phone and a Door Lock...
Page 111 PART 7 MAY 2010 7.1.9 Connecting KDB-D/KDB-S KDB-D and KDB-S are modules installed on a digital phone connected to the OfficeServ 7400 system. The KDB module enhances the functions of the phone and increases the number of local ports according to module types.
Page 112 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 MAY 2010 connection to one telephone. Connecting multiple telephones to a port may result in incorrect operation or damage to the card. See Figure 7.10.
Page 113 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 MAY 2010 RETAINING SCREWS RETAINING SCREWS Figure 7.10 Keyset Base KDB-SLI This daughterboard can be installed only in the DCS 12 or DCS 24 button keyset. Before performing this procedure, unplug the line cord from the keyset and remove the base wedge.
Page 114 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 MAY 2010 MOUNTING SCREWS RIBBON CABLE CONNECTOR Figure 7.11 Installing KDB-DLI Daughterboard OUTPUT JACK Figure 7.12 Keyset Daughterboard Output Jack 7.10...
Page 115 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 MAY 2010 HOOK PLUG RIBBON CABLE FROM DAUGHTERBOARD INTO RIBBON CABLE CONNECTOR P7 Figure 7.13 Connecting Keyset Daughterboard to Keyset PCB RIBBON CABLE...
Page 116 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 MAY 2010 LINE CORD SECOND KEYSET FIRST KEYSET Figure 7.15 Connecting a Keyset to a KDB-DLI LINE CORD SINGLE LINE TELEPHONE FIRST KEYSET Figure 7.16 Connecting a Single Line Telephone to a KDB-SLI...
Page 117 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 MAY 2010 Figure 7.17 Connecting a Station Device to a KDB via MDF CONNECTING TO THE KDBS There are two methods for connecting devices to keyset daughterboards. The simplest method is to connect the second device directly by means of a line cord.
Page 118 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 MAY 2010 HOLES FOR MOUNTING SCREWS NOTE: THE DIRECTORY CARD SLIDE TRAY IS NOT Figure 7.18 Wall-Mounting a Keyset Note: The directory card slide tray is not used when the keyset is wall-mounted.
Page 119 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 MAY 2010 Use screw holes 4 and 5 if you are mounting on dry wall with a hole in the middle for cable access.
Page 120 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 MAY 2010 WALL-MOUNTING iDCS KEYSETS iDCS keysets come equipped with a reversible base wedge. To wall-mount a keyset, remove the wedge from the keyset and mount the wedge to the wall using one of the methods below (see Figure 7.20).
Page 121 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 MAY 2010 BASE STAND SLOTS SCREW HOLES BASE STAND HANDSET HANDSET RETAINING CLIP RETAINING CLIP IN WALL-MOUNTING IN DESKTOP POSITION POSITION Figure 7.21 Wall-Mounting DS 5000, ITP-5121D and ITP-5107S Keysets WALL-MOUNTING SMT-i5200 KEYSETS Assemble the wall-mount bracket where you want to use the phone.
Page 122 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 MAY 2010 2. Remove the desk cradle of the phone. a. Fix one latch of the cradle to the top or bottom groove of the phone.
Page 123 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 MAY 2010 To detach the wall-mounting bracket follow the steps below: You can detach the phone from the bracket by pressing the [Push] section at the bottom of the bracket.
Page 124 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 MAY 2010 2. Remove the cradle of the phone by pressing the [Push] mark on the top of the cradle to push it out 3.
Page 125 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 MAY 2010 Figure 7.22 Attaching 24B/12B to 64BM ATTACHING DCS 32 BUTTON AOM AND DCS 64BM WITH MASTER STATION These new Ultra Base Wedges allow a connector clip (packaged with 64BM and AOMs) to be connected to the underside of the new style wedge and attach AOM(s) or 64BM(s) together with the main or “master”...
Page 126 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 MAY 2010 Figure 7.23 Attaching 24B/12B to AOM ATTACHING iDCS 64 BUTTON MODULES TO AN iDCS KEYSET First, remove the base wedge from the iDCS 64BM and attach the bracket to it with two of the screws provided (see Figure 7.24).
Page 127 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 MAY 2010 7B / SINGLE LINE ULTRA BASE WEDGE AOM ULTRA BASE WEDGE METAL CONNECTOR CLIP 7B/SINGLE LINE ULTRA BASE WEDGE 64BM ULTRA BASE WEDGE METAL CONNECTOR CLIP Figure 7.24 Attaching 7B/Single Line to AOM or to 64BM...
Page 128 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 MAY 2010 Figure 7.25 Attaching iDCS 64 Button Module to an iDCS Keyset 7.24...
Page 129 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 MAY 2010 REMOVE KNOCKOUTS Figure 7.26 Attaching iDCS 14 Button Module to an iDCS Keyset ATTACHING DS 64 BM TO a DS 5021D or a DS 5014D KEYSET First, attach the bracket to the keyset with two of the screws provided.
Page 130 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 MAY 2010 SMT-i5264 ADD ON MODULE The SMT-i5264 module can be used beside any ITP 5100 keysets, SMT-i Series, and TDM phones . The cosmetic design matches the SMT-I 5000 Series phones. The SMT-i5264 Add On Module only attaches to SMT-i5200 Series.
Page 131 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 MAY 2010 SETTING-UP SMT-i5264 AOM SMT-i5264 AOM will register to the OfficeServ system as an IP phone device. It need the IP phone ID and password during the registration. The SMT-i5264 will receive an IP phone extension.
Page 132 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 MAY 2010 o Server IP Address: (OfficeServ IP address from MMC 830) o (use navigation key to move to the following fields) o Server ID: (ITP ID from MMC 840)
Page 133 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 MAY 2010 7.1.10 Connecting the SMT-A52GE Gigabit Adaptor The Gigabit Adaptor processes the Gigabit data for a Gigabit LAN connection on the PC connected to the SMT-i5200 series IP phone.
Page 134 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 MAY 2010 HOW TO CONNECT TO A PHONE 1. Separate the cradle at the back of the phone. 2. Mount the Gigabit Adaptor onto the back of the body.
Page 135 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 MAY 2010 3. Connect the cable. When PoE is supplied via the LAN: Handset Headphones Network (PoE Switch) When PoE is not supplied via the LAN:...
Page 136: Connecting Additional Equipment
This section describes how to connect optional equipment, such as Music on Hold (MOH)/Background Music (BGM) sources, external page devices, common bells, and PCs for WebMMC/Installation Tool/SMDR/CTI to the OfficeServ 7400 system. The following table lists the default MISC Numbering Plan defined in MMC 724.
Page 137 PART 7 MAY 2010 7.2.1 Connecting MOH/BGM Equipment The OfficeServ 7400 system offers Music on Hold. The system provides internal tone/music and external music sources per C.O. or extension lines as the music source. Two external music sources are offered. Connect the music sources to the MISC port of the LP40 board.
Page 138 Instead of an internal speaker, external broadcasting equipment, such as amps or speakers, and additional equipment that can broadcast page (ring) signals outside a building can be connected to the OfficeServ 7400 system. Connect external/additional paging equipment to the MISC 1 and MISC 2 ports of the LP40 board.
Page 139 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 MAY 2010  MISC 1 and MISC 2 ports are located on the front panel of the LP40. Dry Contact Dry Contact is a switch that can connect or cut the power or line to external equipment.
Page 140 7.2.6 Connecting WEBMMC/OIT to the OfficeServ 7400 The WebMMC/OIT (OfficeServ Installation Tool) program is a web-based administrative tool that allows you to locally or remotely program and configure the OfficeServ 7400 system. Please refer to the WebMMC or OIT User manual for installation and user instructions.
Page 141 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 JANUARY 2011 7.2.7 Device Manager (DM) Tool The OfficeServ Device Manager is a Windows™ application that allows programming of the OfficeServ™ 7000 Series phone systems from a PC over a data network or modem. The Device Manager allows access to OfficeServ™...
Page 142 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 JANUARY 2011  Compare Databases The Database Compare function helps you track changes between archives by detecting and displaying any differences between two saved databases.
Page 143 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 JANUARY 2011 Client Application: The client application can be used on OfficeServ 7000 series systems using software version 4.51 and lower. LAUNCHING DEVICE MANAGER Before you can successfully access an OfficeServ System using the embedded Device Manager via a web browser, there are a few things that need to be set or verified.
Page 144 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 JANUARY 2011 3. Java Plug-In Java Web Start Plugin should be installed to use OfficeServ DM. If it’s not, you will be prompted to download it when you attempt to launch Device Manager.
Page 145 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 JANUARY 2011 5. Ports When using a public network to access an OfficeServ system with Device Manager, firewall ports 80 and 21 must be opened on the router.
Page 146 You may see the following warning screen. Simply click on the Run option if you do. Figure 7.40 Security Warning Device Manager will open in a separate window. This may take up to 15 seconds to open. The default Login ID is admin and the default password is samsung. Figure 7.41 DM Login Page 7.42...
Page 147 LAUNCHING THE OFFICESERV DEVICE MANAGER CLIENT APPLICATION Unzip the file obtained from the Samsung GSBN website. The zip file will contain one file - OSDM.JAR file. This is the file used to launch Device Manager. For ease of use, we recommend placing this file on your desktop.
Page 148 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 JANUARY 2011 LINK SETUP The Link Setup window is a connection manager for your OfficeServ system connections. You must enter a site into the Site list before connecting to an OfficeServ System.
Page 149 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 JANUARY 2011 Default Port sets the IP connection ports to use for this site. The default is 5090 for programming and 5003 for Media Card access. To set new values you must uncheck the Default Port checkbox.
Page 150 Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 JANUARY 2011 2. Modem Options The Modem Options tab allows you to set configuration parameters for MODEM connections. Once changes have been made you must click [Apply] to save them.
Page 151: Figure 7.47 Connect To An Os System Using Client App Method
Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 7 JANUARY 2011 CONNECT TO AN OFFICESERV SYSTEM USING THE CLIENT APPLICATION There are a couple of different methods you can use to connect to a system: 1.
Page 152 You’ll be prompted to enter the ID and password. Default values are:  ID = Admin  Password = samsung Figure 7.48 DM Login Page Please refer to the OfficeServ Device Manager User Manual for detailed instructions on how to use Device Manager.
Page 153 Manual). This MMC can also configure the reports to be sent to PCs running 3 party applications (i.e. SMDR Reporting Packages, etc.). The OfficeServ 7400 can also print various reports to a LAN printer. Connect a LAN printer to a network segment that is routable to the MP40 LAN connection.
Page 154 PART 7 JANUARY 2011 7.2.9 OS 7400 and ANALOG TERMINAL ADAPTERS (ATAs) The OfficeServ 7400 can be SIP enabled (SIP licenses required) to interface with other 3 party analog terminal adapters (ATA) devices, to provide voice connectivity to a VoIP network. The SIP enabled adapters can be used to support specialized voice applications such as: ...
Page 155: Power Up Procedures
90%. Take special caution since humidity affects the electrical components and connectors of the system.  Direct sunlight and dust: The room where the OfficeServ 7400 system is installed should be protected from direct sunlight and should have ventilation systems to prevent the system from malfunctioning due to dust.
Page 156: Checking The Fan
Home Page Home Page Table of Contents Table of Contents OfficeServ 7400 INSTALLATION TECHNICAL MANUAL PART 8 MAY 2010 Check the LEDs of the MP40 and LP40 boards. The RUN LED of the MP40 board lights green and the SM LED flashes when the system normally starts the booting process.
Page 157: Numbering Extensions And C.o. Lines
PART 8 MAY 2010 8.4 NUMBERING EXTENSIONS AND C.O. LINES Once the OfficeServ 7400 system is booted, the MP40/LP40 board verifies the boards mounted on each slot and saves this information as the default configuration of the system. According to the setting of the S2 switch (SW6, SW7, SW8) of the MP40 board, the OfficeServ 7400 system assigns 3 or 4 digits to C.O.
Page 158: Software And Database Management
MANAGEMENT 9.1 SOFTWARE MANAGEMENT The OfficeServ 7400 operating software is stored on the media card, which is inserted into the front of the MP40 card. The SD/Smart Media/MMC+ card has 1GB/32MB/64MB of NAND flash memory and is formatted, with a custom format to allow faster loading, in a similar manner to a hard disk.
Page 159 PART 10. ADDING BOARDS TO THE SYSTEM 10.1 ADDING STATIONS AND TRUNKS 1) Power the OfficeServ 7400 OFF before adding a new board. Locate a suitable empty card slot. Having located a suitable slot, insert the new card into the slot and push firmly in the middle of both card ejectors on the card to ensure that it is fully inserted into the back plane connector.

Samsung OfficeServ 7400 Technical Manual

Connecting Stations and Additional Equipment

Power up Procedures

Software and Database Management

Quick Links

Related Manuals for Samsung OfficeServ 7400

Summary of Contents for Samsung OfficeServ 7400

Table of Contents