hit counter code
FAAC B 604 Manual
  1. Manuals
  2. Brands
  3. FAAC Manuals
  4. Automatic Barriers
  5. B 604
  6. Manual
FAAC B 604 Manual

FAAC B 604 Manual

Hide thumbs Also See for B 604:
1
2
3
4
5
6

Advertisement

Table of Contents

1. DESCRIPTION OF COMPONENTS
2. TECHNICAL SPECIFICATIONS
3. DIMENSIONS
4. ELECTRIC PREPARATIONS (standard system)
4. INSTALLING THE AUTOMATED SYSTEM
4.1. PRELIMINARY CHECKS
4.2. ON-COLUMN INSTALLATION
4.3. ON-WALL INSTALLATION
4.4. CLOSING DIRECTION
4.5. SECURING THE ROD
5. START-UP
6. MANUAL OPERATION
7. RESTORING NORMAL OPERATION MODE
8. AVAILABLE ACCESSORIES
9. MAINTENANCE
10. REPAIRS
10.1. REPLACEMENT OF FLASHING LAMP
Manufacturer:
FAAC S.p.A.
Via Benini, 1 40069 Zola Predosa Bologna ITALY
Address:
Declares that:
Operator mod. B 604 24V with 230 Vac power supply
• is built to be incorporated in a machine or to be assembled with other machinery to create a machine under the provisions of
Directive 98/37/EC;
• conforms to the essential safety requirements of the other following EEC directives:
conforms to the essential safety requirements of the other following EEC directives:
73/23/EEC and subsequent amendment 93/68/EEC.
89/336/EEC and subsequent amendment 92/31/EEC and 93/68/EEC
Furthermore, the manufacturer declares that the machinery must not be put into service until the machine into which it will be
incorporated or of which it will become a part has been identified and its conformity to the conditions of Directive 98/37/EC has
been declared.
Bologna, 30-06-2007
Read this installation manual to the full before you begin installing the product.
The symbol
indicates notes that are important for the safety of persons and for the good condition of the automated system.
The symbol
INDEX
CE DECLARATION OF CONFORMITY
Notes on reading the instruction
draws your attention to the notes on the characteristics and operation of the product.
Managing Director
A. Bassi
7
page.8
page.8
page.8
page.8
page.9
page.9
page.9
page.10
page.11
page.11
page.11
page.12
page.12
page.12
page.12
page.12
page.12

Advertisement

Table of Contents
loading

Related Manuals for FAAC B 604

Summary of Contents for FAAC B 604

  • Page 1 10.1. REPLACEMENT OF FLASHING LAMP page.12 CE DECLARATION OF CONFORMITY Manufacturer: FAAC S.p.A. Via Benini, 1 40069 Zola Predosa Bologna ITALY Address: Declares that: Operator mod. B 604 24V with 230 Vac power supply • is built to be incorporated in a machine or to be assembled with other machinery to create a machine under the provisions of Directive 98/37/EC;...

  • Page 2: Technical Specifications

    B 604 AUTOMATED SYSTEM The B 604 automated system is an electronic barrier designed for 2. TECHNICAL SPECIFICATIONS vehicle accesses MODEL B 604 The automated system mainly consists of three parts: • A motor body which integrates the non-reversing low voltage Power supply...
  • Page 3 Always separate connection cables of low voltage acces- Screw the four supplied tie-rods, Fig.7 ref.a, in the respective sories and control cables from power cables. Use separate holes, the ones with the welded nuts. sheaths. Wall the foundation plate as shown in Fig.7, supplying one or more sheaths for routing electrical cables. An arrow is marked on the foundation plate. This arrow must point upward, be visible even after the plate has been wal- led in, and must be oriented toward the release device.

  • Page 4: On-Wall Installation

    Position the cables inside the motor body and close the central 4.3.2. p ositioning the motor body compartment. When you have finished installing the motor support, position and Position the motor body above the column, inserting the guides secure the motor body: of the central support in the two rectangular pockets on the Unscrew the securing screws of the upper housing (Fig.
  • Page 5 Fig. 27 if all connected accessories are bearing rod and the release unit must be reversed. operating correctly, addressing special attention to the safety The B 604 automated system can be coupled to three different devices. types of rod: • Perform the programming procedure following the instructions •...

  • Page 6: Manual Operation

    Position the rear plug of the release housing (Fig. 32 ref. a) • Open, on the front plug, the pre-perforated facility for the type of The following accessories are available for the B 604 automated installed rod, see Fig. 33 and fasten it to the release housing. system.

Table of Contents