Samsung Verizon Galaxy Note 4 Manual
Display / assembly replacement
Hide thumbs
Also See for Verizon Galaxy Note 4:
- User manual (228 pages) ,
- Important information manual (60 pages) ,
- Service manual (43 pages)
Advertisement
Quick Links
Scope:
Details:
Display / Assembly Replacement
ESD Strap
(From Kit):
Phillips #00 Screwdriver
Tweezers
Required Tools
Plastic Spudger
Plastic Opening Pick
Personal Protective Equipment (Safety Glasses and Gloves)
SKU
SAM1913
SAM1914
Parts Required
Adhesive (If necessary)
Roll Adhesive (If necessary)
Perform a full function test to ensure that there are no other issues with the phone. I.E. No power, will not make a phone call, etc. Check phone Power Levels.
Perform a full function test to ensure that there are no other issues with the phone. I.E.
Go to Settings, About Phone, Status and check Signal Strength. Annotate power levels for future tests after repair.
No power, will not make a phone call, etc. Any issue outside of the LCM and the repair
PHONE RF FIELD TEST
should not be performed.
Perform this test BEFORE conducting the screen replacement to confirm the phone is working properly and repeat after screen replacement is complete to
confirm the phone is properly working.
PHONE RF FIELD TEST
Test procedure
Review the current signal strength by following these paths to get to the Signal Strength screen.
To put the Phone in field test mode
Dial *3001#12345#*
Perform this test BEFORE conducting the screen replacement to confirm the phone is
Pre Repair Test
working properly and repeat after screen replacement is complete to confirm the
Instructions
phone is properly working.
Click on Apps
Click on Settings
Scroll to About
Phone and click.
Click on Status
Annotate the signal
strength for
reference once
repair is complete.
Once repairs are completed Signal Strength must be compared to the original
readings. Strength of signal must be within -10 dBm of the original reading at the
same phone location. Example: If first reading is -91 dbm, new reading cannot be
greater than -101 dBm. Readings moving up show a stronger strength and are
acceptable. Example: From -91dBm to -81dBm. -150 dBm is a no signal
indication.
Note:
Clean Work area of all or any debris after Repair.
For Reference when repairing the:
Description
Black
White
Pre-Cut
Cut as needed
Samsung Galaxy Note 4 Black / White
Specifications
QTY
1
1
1
1
Advertisement
Related Manuals for Samsung Verizon Galaxy Note 4
Summary of Contents for Samsung Verizon Galaxy Note 4
- Page 1 Scope: For Reference when repairing the: Samsung Galaxy Note 4 Black / White Details: Display / Assembly Replacement ESD Strap (From Kit): Phillips #00 Screwdriver Tweezers Required Tools Plastic Spudger Plastic Opening Pick Personal Protective Equipment (Safety Glasses and Gloves)
- Page 2 Disassembly Step 1: Remove the Battery Door. Step 2: Remove the Battery. Step 3: Remove the SIM and SD Cards if present. Step 4: Remove the Stylus from the assembly. Step 5: Using the Phillips #00 Screwdriver Remove the 13 Phillips Screws outlined.
- Page 3 Step 8A: Apply heat over the entire surface area of the LCM Assembly using a heat gun. Exercise caution when heating any handset to ensure that the temperature does not exceed the point where unintended damage occurs. Step 9: Insert the full length of the opening pick between the Plastic Frame and the Copper Foil on the back of the LCM Assembly.
- Page 4 Assembly Step 1: If present, remove the film from the back of the LCM by pulling up on the blue and green tabs. This will expose the copper film on the back of LCM along with the top and bottom adhesives. Step 1A: If the adhesive is not pre-installed, the two following procedures may be followed.
- Page 5 Step 7: Using the Phillips #00 Screwdriver Install the 13 Phillips Screws outlined. Step 8: Install the Stylus from the assembly. Step 9: Install the Battery. Step 10: Install the SIM and SD Cards if present. Step 11: Install the Battery Door. Note: Clean Work area of all or any debris after Repair.