Page 1
ORDER NO.DSD0302003C8 DVD Video Recorder DMR-E50EB DMR-E50EG DMR-E50GCS Colour (S).......Silver Type SPECIFICATIONS Specifications Power supply: AC220-240 V, 50 Hz (For E50EB/ EG) AC220-240 V, 50/ 60 Hz (For E50GCS) Power consumption: 29 W Recording system: DVD video recording standards (DVD-RAM),...
Page 2
PAL I 75 ohm (For E50EB) PAL I 75 ohm terminated (For E50EB) PAL B/ G/ H 75 ohm terminated (For E50EG/ GCS) Channel Coverage: DMR-E50EB only UHF: CH 21-68 DMR-E50EG only VHF: CH E2-E12, A-H2 (For Italy) UHF: CH 21-69...
Page 3
CH S01-S05 (S1-S3) CATV S1-S20 (M1-U10) S21-S41 [8MHz, RASTER] DMR-E50GCS only VHF: CH E2-E12 UHF: CH 21-69 CH S01-S05 CATV CH M1-M10 CH U1-U10 CH S21-S41 RF Converter UHF: CH21-68, 71 ± 3dB Output: 75 ohm (For the E50EB) Not provided (For the E50EG/ GCS) Video Video System:...
Laser Power: No hazardous radiation is emitted with the safety protection Notes: Mass and dimensions shown are approximate. Specifications are subject to change without notice. Notes: The part of DVD RAM Drive (VXY1772) is listed separately. Please refer to ORDER NO. RAM0301002C0. 1.
Figure 1 1.1.2. LEAKAGE CURRENT HOT CHECK (See Figure 1 1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check. 2. Connect a 1.5k , 10 watts resistor, in parallel with a 0.15 F capacitors, between each exposed metallic part on the set and a good earth ground such as a water pipe, as shown in...
transistorsand semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by electro static discharge (ESD). 1. Immediately before handling any semiconductor component or semiconductor- equipped assembly, drain off any ESD on your body by touching a known earth ground.
( As shown in 16.2. The Main P.C.B. ) NOTE: The lithium battery is a critical component. ( Type No.: CR2354-1GUF Manufactured by Panasonic. ) It must never be subjected to excessive heat or discharge. It must therefore only be fitted in equipment designed specifically for its use.
5. Handling the Lead-free Solder 5.1. About lead free solder (PbF) Distinction of PbF P.C.B.: P.C.B.s (manufactured) using lead free solder will have a PbF stamp on the P.C.B. Caution:...
Pb free solder has a higher melting point than standard solder; Typically the melting point is 50 - 70°F (30 - 40°C) higher. Please use a high temperature soldering iron. In case of the soldering iron with temperature control,please set it to 700 ± 20°F (370 ± 10°C).
Page 12
6.2. Service Explorer in Detail 6.2.1. Does not operate items needed: RAM drive, digital P.C.B., remote control. Conditions: Nothing special.
Page 13
6.2.2. Poor Pictures Items needed: RAM drive, Digital P.C.B., RF cable, AV cable. Conditions: Check with TU IN-AV OUT(EE). When recording or playback is partially needed, follow the instructions.
Page 15
6.2.3. Other Items needed: Digital P.C.B., HDD. Conditions: Nothing special.
Procedure Item to Check Turn on the power. The Panasonic RAM disc should be recognized. Enter the EE (TU IN / AV IN - AV OUT) mode. No abnormality should be seen in the picture, sound or operation.
Item Contents Item Contents Check Block noise Distorted sound Crosscut noise noise (static, background noise, etc.) Dot noise The sound level is too low. Picture disruption The sound level is too high. Picture Sound Not bright enough The sound level changes. Too bright Flickering color Color fading...
8.2. P.C.B. Positions 8.3. The Top Cover 1. Remove the 2 screws (A) and 3 screws (B). 2. Open the both ends at the front side of the Top cover a bit and lift the Top cover in the direction of the arrows.
Page 19
8.4. The Digital P.C.B. 1. Remove the FFC. CAUTION: When replacing Digital P.C.B., pay attention as below.
Page 20
2. Remove the 2 screws. 3. Pinch the tab with the pliers to pull out the 3 Connectors and Digital P.C.B.
Page 22
2. Remove the 2 tab (A) and 3 tab (B) in this order. (The tab (A) and the tab (B) should be removed at the same time, respectively.) 3. Move the front panel to your side slowly and remove it.
Page 23
8.6. The Front (L) and (R) P.C.B. 1. Remove the 2 screws and remove the Front Angle. 2. Remove the 4 screws (A) and remove the Front (R) P.C.B. 3. Remove the 2 screws (B) with Earth plate and remove the Front (L) P.C.B.
Page 24
8.7. The DVD-RAM Drive 1. Remove the 4 screws. 2. Pull out the DVD-RAM Drive vertically and remove the connector.
8.8. The Rear panel 1. Remove the Fan Motor connector.
Page 26
2. Remove the 8 screws (A) and a screw (B). 3. Remove the 2 tabs and remove the Rear panel.
Page 27
8.8.1. In case of removing Fan motor from Rear panel 1. Remove a screw. 2. Push tip of rivet to remove it.
Page 28
8.9. The Main Power Supply P.C.B. and Main P.C.B. 1. Remove the 2 connectors. 2. Remove the 3 screws (A) and 2 tab (A). 3. Remove the Main Power Supply P.C.B and tab (B), pull out it in the direction of the arrow.
1. Remove the solder. 2. Pull out the VIF Decoder P.C.B. and Nicam/Decoder P.C.B. 9. Service Positions 9.1. Checking procedure Note: For the disassembling procedure, see the section 8. 9.2. Checking the Digital P.C.B., RGB P.C.B. and Scart P.C.B. 1. Remove the Top Cover. 2.
Page 33
4. Remove the Digital P.C.B. 5. Pull out the RGB P.C.B. 6. Use the extension cable (RFKZ0168) to connect the Main P.C.B. and Fan Motor. 7. Use the extension cable (RFKZ0164) to connect the Main P.C.B. and Digital P.C.B. 8. Use the extension FFC (RFKZ0125) to connect the RAM Drive and Digital P.C.B. 9.
Page 34
1. Remove the Top Cover. 2. Remove the Front Panel. 3. Remove the Rear Panel. 4. Remove the Power Supply P.C.B., Main P.C.B. and RAM Drive. 5. Use the extension cable (RFKZ0168) to connect the Main P.C.B. and Fan Motor. 6.
Page 35
9.4. Checking the Power Supply P.C.B. 1. Remove the Top Cover. 2. Remove the Front Panel. 3. Remove the screw which fixed Rear Panel and AC Inlet on the Power Supply P.C.B.. 4. Remove the Power Supply P.C.B., fix it on the insulation sheet. 5.
Page 36
Service tools Extension Cable (Main P.C.B. - RFKZ0165 (20-pin) Front (L) P.C.B.) Extension Cable (Power supply RFKZ0166 (10-pin) P.C.B. - Front (R) P.C.B.) Extension Cable (Main P.C.B. - RFKZ0170 (19-pin) Power supply P.C.B.) Extension Cable (Main P.C.B. - RFKZ0171 (15-pin) Power supply P.C.B.) 10.
Each buttons Functions name To turn power on or off on the DVD. VIDEO Plus+ To set timer program using G (Show View/G code/Show view/VIDEO Plus+ code) To set AV input on the TV. Numeric To put each number for buttons(10key) selecting each functions.
Page 38
<SEARCH> To set the cue or playback,playback 30seconds review during playback. previous by pressing the button. Below buttons are located inside slide cover. Each buttons Functions name REC MODE To set recording speed. F Rec To frexible recording with best quality to caluculate recording rate within remaining recording time.
Page 39
Service mode setting: While the power is off, press TIME SLIP, STOP and OPEN / CLOSE simultaneously for five seconds. Item FL display Key operation Mode name Description Remote controller key Clear item Items 1-20 are cleared. [0] [0] while in service mode Error code display FL display of the last [0] [1] while in service mode...
Page 40
Item FL display Key operation Mode name Description Remote controller key RTSC return XP (A& Disc recording of L1 Initialization mode (EE2/ [1] [3] while in service mode input Encoded and Interlace/ XP/ Audio decoded for external 48kHz) output without playback.
Page 41
Item FL display Key operation Mode name Description Remote controller key Laser use time To check laser use [4] [1] while in service mode display time of drive Laser error count The number of times [4] [3] while in service mode that a laser error has occured due to a defective disc or...
Page 42
Item FL display Key operation Mode name Description Remote controller key Front connection Press all the main [5] [4] while in service mode inspection unit’s buttons and check the connection with the Main P.C.B.. AV4-AV1 (RGB) Video signal at AV4 [8] [0] while in service mode SELECT should output with...
Page 43
10.2.2. Other special modes Item FL display Key operation Mode name Description Remote controller key Main unit *All the main unit’s When the power is off, press initialization parameters are SKIP(R), TIME SLIP and OPEN/ initialized. CLOSE simultaneously for five seconds.
Page 44
Diagnosis Description FL display Display Remote control Display appears when main unit and remote mode error controller modes are not matched. Abnormal inner Display appears when the drive temperature temperature exceeds 71Åé. Main unit is powered off detected forcibly. For 30 minutes after this, all key entries are disabled.
Page 45
Diagnosis Description FL display Display Initialization error Display appears when initialization error is when main detected after starting up main microprocessor microprocessor for program recording. The is started up for event is saved in memory. program recording Remains displayed. Unsupported *A disc an unsupported format was played, UNSUPPORT disc error...
Page 46
10.3.2. Error generating disk state 10.3.3. Disk production maker ID * Since a display is arbitrarily set up by the disk producer side, the above-mentioned display may be changed.
Page 47
Please make it reference as an example of a display. 11. Abbreviations INITIAL/LOGO ABBREVIATIONS A0~UP ADDRESS ACLK AUDIO CLOCK AD0~UP ADDRESS BUS ADATA AUDIO PES PACKET DATA ADDRESS LATCH ENABLE AMUTE AUDIO MUTE AREQ AUDIO PES PACKET REQUEST AUDIO RF SERVO AMP INVERTED INPUT SERVO AMPOUTPUT ASYNC...
Page 48
INITIAL/LOGO ABBREVIATIONS ERROR TORQUE CONTROL ERROR TORQUE CONTROL REFERENCE ENCODER SELECT ENCSEL EXTERNAL M CLOCK (81MHz/ ETMCLK 40.5MHz) ETSCLK EXTERNAL S CLOCK (54MHz) FBAL FOCUS BALANCE FCLK FRAME CLOCK FOCUS ERROR FOCUS ERROR AMP INVERTED INPUT FOCUS ERROR AMP OUTPUT FREQUENCY GENERATOR FREQUENCY SUB CARRIER FSCK...
Page 49
INITIAL/LOGO ABBREVIATIONS READ ENABLE RFENV RF ENVELOPE RF PHASE DIFFERENCE OUTPUT (CD-ROM) REGISTER SELECT RSEL RF POLARITY SELECT RESET RESERVE SBI0, 1 SERIAL DATA INPUT SBO0 SERIAL DATA OUTPUT SBT0, 1 SERIAL CLOCK SERIAL DATA CLOCK SCKR AUDIO SERIAL CLOCK RECEIVER SERIAL CLOCK SCLK...
INITIAL/LOGO ABBREVIATIONS VBLANK V BLANKING COLLECTOR POWER SUPPLY VOLTAGE VCDCONT VIDEO CD CONTROL (TRACKING BALANCE) DRAIN POWER SUPPLY VOLTAGE VREF VIDEO FEED BACK VOLTAGE REFERENCE SOURCE POWER SUPPLYVOLTAGE WAIT BUS CYCLE WAIT WDCK WORD CLOCK WRITE ENABLE HIGH WORD SELECT RECEIVER X' TAL XALE X ADDRESS LATCH ENABLE...
Page 51
Therefore, there may exist some errors in the voltage values, depending on the internal impedance of the DC circuit tester. 12.1. Main Power Supply P.C.B. 12.2. Main P.C.B. 12.3. RGB P.C.B. 12.4. Scart P.C.B. 12.5. Nicam/Decoder P.C.B. 12.6. Front L P.C.B. 12.7.
12.8. P9001 Connector 12.9. P9001 Waveform 13. Block Diagram 13.1. Power Supply Block Diagram 13.1.1. Integrated Circuit Power Supply Chart (PSC 1 - PSC 19) 13.2. Analog Video Block Diagram 13.3. Analog Audio Block Diagram 13.4. Timer Block Diagram...
Page 64
X SW+5.15V PS105 PP1501 Q103 REG.D+12V REG.+12V (TO DVD RAM DRIVE) Q105 IC102 PHOTO SHUNT COUPLER REG. X SW+13V PS105 PP1501 Q107 REG.D+5V REG.+5V (TO DVD RAM DRIVE) Q104,Q106 DR P ON(H) PS105 PP1501 COLD DMR-E50EB/EG/GCS Power Supply Block Diagram...
Page 65
IC7401 (REG.AU+12V) (REG.PS+12V) VOUT REG.AU+12V(PSC 4) VOUT PS+12V(PSC 16) ON(H) ON(H) POWER SAVE(H) FROM TIMER SEC. IC4013 QR4006,4007 (IC7502- (REG.AU+9V) VOUT REG.AU+9V(PSC 19) T7501 IP7501 (POWER TRANS.) UNREG+38V TO DU7402- DMR-E50EB/EG/GCS DMR-E50EB/EG/GCS Power Supply Block Diagram Power Supply Block Diagram...
Page 66
PSC 1. X SW+5.15V PSC 9. REG.AU+5V Ref. No. Pin. No. Schematic Name Ref. No. Pin. No. Schematic Name IC7502 15,34,69 Timer (Main) IC4402 8 AV Input (Digital) 105,106,108 IC4403 IC50010 6 AV Decoder (Digital) IC7504 IC7506 PSC 10. REG.DAC+3.3V IC7508 Ref.
Page 67
PSC 13. D+3.3V PSC 18.REG.D+5V Ref. No. Pin. No. Schematic Name Ref. No. Pin. No. Schematic Name IC3406 7,15,31,43 AV Encoder (Digital) IC4005 8 Audio Main (Main) 47,54,70,81 IC4006 88,91,99,106 IC4007 114,125,130 138,152,168 IC50001 1,11,14,19 AV Decoder (Digital) PSC 19.REG.AU+9V IC50002 1,3,9,14 Ref.
Page 68
SCART Q3001,3002,FL3001 V OUT PP7401 PS3901 Y SEP.AND TUNER Y IN BUFFER SLICER VIDEO VIDEO SLICER 42 TO TIMER VIDEO (Q7505,Q7507) Q3003,3004,FL3002 DU7402 C SEP.AND C IN Y/C SEPA. BUFFER Q7402 TUNER VIDEO VIDEO OUT DMR-E50EB/EG/GCS Analog Video Block Diagram...
Page 69
R CH IN TUNER L PK7302 PK7702 DECODER L PP7403 PS3903 DECODER L TUNER L DECODER L L CH IN AUDIO IN CH1(L) IC4007 IC4005 P9002 PP9702 IEC OUT FROM IC4006 DIGITAL OPTICAL D+5V (DIGITAL AUDIO OUT) DMR-E50EB/EG/GCS Analog Audio Block Diagram...
Page 71
Main Net Ref.No.9900 SERIES WORKING Digital P.C.B.connect circuit PP9701,PP9702,PP9703 MEMORY Main BUFFER MAIN CPU LOADER Video I/O Main Ref.No.3000 SERIES 16bit/128M- DMR-E50EB/EG/GCS 16bit/64M 16bit/64M P.C.B. SDRAM SDRAM SDRAM Audio Main Ref.No.4000 SERIES Digital Section Block Diagram Timer Ref.No.7500 SERIES IC50002...
Page 72
IC Pin Terminal Chart IC Pin Terminal Chart IC3203 / VAD CON IC3402 / AV ENC IC3402/AV ENC IC3203/VAD CON IC50003/AV DEC IC6004 / MAIN CPU IC6002 / W-MEMORY IC3401/SDRAM(32bit/64M) SIGNAL NAME SIGNAL NAME SIGNAL NAME SIGNAL NAME Port Name Pin No Pin No Port Name...
20-1 12-3 17-1 19-1 20-2 17-2 19-2 IC6004/MAIN CPU IC3406 / RTSC IC6701/GLUE IC6007 / BUFFER IC6006 / LOADER IC50003 / AVDEC IC6004 / MAIN CPU IC6701 / GLUE IC6006 / LOADER SIGNAL NAME SIGNAL NAME Pin No Port Name Pin No Port Name Pin No...
AV-Encoder Ref.No.3400 SERIES Digital igital P.C.B.connect circuit PP9701,PP9702,PP9703 AV-Decoder Ref.No.50000 SERIES P.C.B. eo I/O Section Ref.No.3000/3900/4900 SERIES AV-Input Ref.No.3200/4400 SERIES dio Main Section Ref.No.4000 SERIES System Control Ref.No.6000 SERIES mer Section Ref.No.7500 SERIES Glue Ref.No.6700 SERIES DMR-E50EB/EG/GCS Interconnection Schematic Diagram...
10V220 R326 ZD303 C308 R341 C313 R333 3.32K MAZ8051 0.033 46.4K R321 R114 DMR-E50EB/EG/GCS ER SHOWN ON THIS DRAWING FOR ORDERRING.THE CORRECT PART NUMBER IS SHOWN Main Power Supply SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. Schematic Diagram...
Page 79
14.3. Sub Power Supply Schematic Diagram (P) (Main P.C.B. 1/5) TO P1102 MAIN POWER SUPPLY P.C.B. PP1501 LB1501 J0JHC0000032 D 1.8V D 1.8V LB1502 J0JHC0000032 D 3.3V D 3.3V LB1503 J0JHC0000032 X SW 5.15V LB1504 J0JHC0000032 X SW 5.9V LB1505 J0JHC0000032 X SW 13V P OFF(L) IC1501...
C1528 ANA 3.3V C1512 25V47 P OFF(L) DMR-E50EB/EG/GCS Sub Power Supply Section (Main P.C.B. (1/5)) NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING.THE CORRECT PART NUMBER IS SHOWN Schematic Diagram(P) IN THE PARTS LIST,AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
DGND COUT DM COUT DM DGND Y GCA CONT Y GCA CONT CLAMP DC CLAMP DC CLAMP PULSE CLAMP PULSE DGND V YIN DM V YIN DM DGND CPNCIN DM CPNCIN DM DMR-E50EB/EG/GCS Main Net Section(Main P.C.B. (2/5)) Schematic Diagram(M)
Page 83
R7409 270 R7414 100 RFC A OUT E50EB C7429 QR7406 3300P:E50B R7413 100 R7423 UNR211500L 0.1:E50EG/GCS 5.6K (MUTE) RFC A MUTE QR7407 UNR221500L (MUTE) IIC CLK IIC DATA PROG(H) CPS V OUT DMR-E50EB/EG/GCS Main Net Section(Main P.C.B. (2/5)) Schematic Diagram(M)
Page 84
NIX R OUT 1 DECODER L DECODER L DECODER R DECODER R L3 IN L L3 IN L L3 IN R L3 IN R AUDIO MUTE AUDIO MUTE PWR SAVE(H) PWR SAVE(H) DMR-E50EB/EG/GCS .B. (2/5)) Main Net Section(Main P.C.B. (2/5)) Schematic Diagram(M)
Page 85
14.5. Video I/O Schematic Diagram (V) (Main P.C.B. 3/5) JC REG5V CLAMP PULSE CLAMP DC Y GCA CONT ANA5V COUT DM LB3015 YOUT DM J0JHC0000032 LB3014 C3023 C3028 J0JHC0000032 0.01 0.01 C3019 D3001 0.01 R3061 MA2C165001VT C3068 15P A4 S IN L MIX L OUT2 C3070 6.3V47 R3026 1K...
Page 88
RGB IN(H) R3073 5600 AV2 V IN DMR-E50EB/EG/GCS Video I/O Section(Main P.C.B. (3/5)) NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING.THE CORRECT PART NUMBER IS SHOWN Schematic Diagram(V) IN THE PARTS LIST,AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 89
14.6. Audio Schematic Diagram (A) (Main P.C.B. 4/5) IP4001 D4FAR4000001 C4019 (VSF0015A04T) 16V10 R4022 C4031 C4027 R4021 50V1 50V1 C4021 16V10 R4023 R4015 L4002 R4039 ELESE220KA C4053 C4054 C4022 6.3V47 AADC L MIXLOUT DM L2 IN L L2 IN R C4069 0.1 MIXROUT DM R4099...
C4070 C4072 10V220 10V220 DMR-E50EB/EG/GCS Audio Main Section(Main P.C.B. (4/5)) NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING.THE CORRECT PART NUMBER IS SHOWN Schematic Diagram(A) IN THE PARTS LIST,AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 94
METER L METER R UNREG 38V DDGND DMR-E50EB/EG/GCS Timer Section(Main P.C.B. (5/5)) NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. THE CORRECT PART NUMBER IS SHOWN Schematic Diagram(T) IN THE PARTS LIST, AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 95
14.8. Digital Net Schematic Diagram (DN) (Digital P.C.B. 1/6) TO PP9701 MAIN P.C.B. (MAIN NET) P9001 CNPNCIN DM DGND V YIN DM DGND CLAMP PULSE CLAMP DC Y GCA CONT DGND COUT DM DGND YOUT DM DGND RPROUT DM DGND BPBOUT DM GPYOUT DM DGND...
Page 96
(REG.SD+1.8V) C9004 UARTP2G UARTG2P DMR-E50EB/EG/GCS E:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. THE CORRECT Digital Net Section(Digital P.C.B.(1/6)) PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 97
14.9. AV Input Schematic Diagram (AI) (Digital P.C.B. 2/6) D3.3V D1.8V ANA 3.3V FL3213 F1H0J1050018 CLAMP PULSE CLAMP DC R3233 0 CPSVIN DM CPS(H) CL3205 R3220 R3223 6800 Q3202 Y GCA CONT 2SD1819A0L R3219 Q3201 (XVCO) 5600 2SB1218A C GCA CONT R3222 100K (XVCO)
Page 100
XAIOFCS 2 4 6 8 2 4 6 8 MRWR MRWW DMR-E50EB/EG/GCS AV Input Section (Digital P.C.B.(2/6)) NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST. Schematic Diagram(AI)
Page 106
AD:AV Decoder Section(Page: C3ABQG000007 (16bit/128M SDRAM) S:System Control Section(Page: G:Glue Section(Page: NOTE: DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST. DMR-E50EB/EG/GCS AV Encoder Section(Digital P.C.B.(3/6)) Schematic Diagram(EN)
Page 110
FL21 F1H0J1050018 DAC 3.3V 6V100 ANA 3.3V DMR-E50EB/EG/GCS AV Decoder Section J-LINE (Digital P.C.B.(4/6)) NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLY DIFFERNT OR AMENDED Schematic Diagram(AD) REF.NO.50000 SERIES...
Page 111
14.12. System Control Schematic Diagram (S) (Digital P.C.B. 5/6) D 3.3V SD 1.8V XRESET DGND TO DIGITAL JIG P6001 FL6001 XDIAG F1H0J1050018 XDIAG XRESET SBIO MSORX D 3.3V SBO0 MSOTX 42 41 40 39 38 37 36 IC6002 C3ABQG000043 (WORKING MEMORY) XIRQ6 XIRQ6 XIRQ5...
Page 116
SA14 SA13 SA13 SA12 SA12 SA11 SA11 SA10 SA10 DMR-E50EB/EG/GCS System Control Section (Digital P.C.B.(5/6)) NOTE: DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM Schematic Diagram(S) m(S) FOR ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST.
Page 120
MSD31 NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST, DMR-E50EB/EG/GCS AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. Glue Section(Digital P.C.B.(6/6)) Schematic Diagram(G)
Page 121
14.14. RGB Schematic Diagram TO PP3002 MAIN P.C.B. LB3501 (VIDEO I/O SEC.) J0JHC0000032 PS3502 PS 5V SCART V IN R3501 R3507 R3512 AV2 V IN R/C IN G IN C3501 C3502 C3503 Q3501 Q3502 Q3503 6V47 6V47 6V47 2SD0601A0L 2SD0601A0L 2SD0601A B IN (AMP)
Page 122
2SB0709A (AMP) 3529 R3503 NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING.THE CORRECT PART NUMBER IS SHOWN DMR-E50EB/EG/GCS IN THE PARTS LIST,AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. RGB Schematic Diagram...
14.15. Scart Schematic Diagram TO PP7401 MAIN P.C.B. (MAIN NET SEC.) PS3901 IIC CLK IIC DATA PROG(H) R3908 R3909 BOOSTER+5V PS 5V TUNER VIDEO SCART V IN CPS V OUT C3910 C3911 16V10 16V10 CPN Y OUT PS 12V B OUT G OUT R/C OUT GAIN CTL...
Page 126
C3962 100P 100P DMR-E50EB/EG/GCS NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. THE CORRECT PART NUMBER IS SHOWN Scart Schematic Diagram IN THE PARTS LIST, AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 128
HAVE THE SPECIAL CHARACTERISTICS FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS.ONLY THE SAME TYPE. NOTE: DMR-E50EB/EG/GCS DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM VIF Decoder Schematic Diagram FOR ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST.
14.17. Nicam/Decoder Schematic Diagram C7335 C7305 6V100 IC7302 C0EAH0000051 TO PK7701 (RESET) MAIN P.C.B. (MAIN NET) PK7301 TU AUDIO IN LB7303 L7303 J0JCC0000021 G0C1R0JA0019 SW 5V C7303 C7306 C7334 6V100 0.01 50V2.2 C7311 100P R7304 C7301 R7301 C7302 ERJ3GEY0R00V TO PK7702 MAIN P.C.B.
Page 130
TL7303 R7309 R7314 TL7301 LB7302 C7313 C7312 J0JCC0000112 16V10 16V10 C7318 16V10 R7315 C7314 NOTE: DMR-E50EB/EG/GCS DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM Nicam/Decoder Schematic Diagram FOR ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST.
Page 131
14.18. Front (L) Schematic Diagram TO P7501 MAIN P.C.B. (TIMER SECTION) P7001 CPN 2Y IN CPN 2C IN LINE 2V IN L2 C SDET L2 IN(L) L2 IN(R) POW LED KEYIN3(R) KEYIN3(L) KEYIN2(R) KEYIN2(L) < N SW 5V > N SW 5V POWER R7011 R7001...
Page 132
(POWER LED DRIVE) NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE DMR-E50EB/EG/GCS SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. Front (L) Schematic Diagram...
14.18. Front (L) Schematic Diagram 14.19. Front (R) Schematic Diagram 15. Print Circuit Board 15.1. Main Power Supply P.C.B. 15.2. Main P.C.B. 15.2.1. Main P.C.B. (Section 1/4) 15.2.2. Main P.C.B. (Section 2/4) 15.2.3. Main P.C.B. (Section 3/4) 15.2.4. Main P.C.B. (Section 4/4)
Page 136
L118 Q101 C121 IP101 Q109 C116 L107 F101 D112 L113 D115 D116 C112 IP102 R140 JE15 JE16 Q103 L115 Q107 R A K JE10 Q108 JE11 VR102 JE12 PS105 PS102 Q104 Q105 Q106 Main Power Supply P.C.B. IC102 DMR-E50EB/EG/GCS (ETXMM444E4G)
Page 142
DIGITAL P.C.B. OVER VIEW Digital P.C.B. (Component Side) (COMPONENT SIDE) DMR-E50EB (REP3496A), DMR-E50EG (REP3496C) DMR-E50GCS (REP3496CD)
Page 143
DIGITAL P.C.B. OVER VIEW Digital P.C.B. (Foil Side) (FOIL SIDE) DMR-E50EB (REP3496A), DMR-E50EG (REP3496C) DMR-E50GCS (REP3496CD)
Page 144
DIGITAL P.C.B. CKB21 F CKC131 F CL6785 F LB9020 F FL50025 F R3239 C R6742 F RA3414 C RX6048 Integrated Circuit IC3201 F CKB22 F CKC132 F CL6786 F LB9021 F FL50028 C R3240 C R6745 F RA3415 C RX6701 IC3203 C CKB23 F CKC133...
Page 146
C LB3925 F C3920 F C3954 F R3910 F R3934 F R3984 JK3905 Capacitor C3921 C C3955 F R3911 F R3935 F R3985 ADDRESS INFORMATION C COMPONENT SIDE F FOIL SIDE SCART P.C.B. Scart P.C.B. (Component Side) (COMPONENT SIDE) DMR-E50EB/EG/GCS (REP3533A)
Page 147
C LB3925 F C3920 F C3954 F R3910 F R3934 F R3984 JK3905 Capacitor C3921 C C3955 F R3911 F R3935 F R3985 ADDRESS INFORMATION C COMPONENT SIDE F FOIL SIDE SCART P.C.B. (FOIL SIDE) Scart P.C.B. (Foil Side) DMR-E50EB/EG/GCS (REP3533A)
15.7. Nicam/Decoder P.C.B. 15.8. Front (L) P.C.B. 15.9. Front (R) P.C.B. 16. Exploded Views 16.1. Casing Parts & Mechanism Section 1 16.2. Casing Parts & Mechanism Section 2 16.3. Packing & Accessories Section 17. Replacement Parts List Notes: *Important safety notice: Components identified by mark have special characteristics important for safety.
Page 157
*Warning: This product uses a laser diode. Refer to caution statements. *Capacity values are in microfarads ( F) unless specified otherwise, P=Pico-farads (pF), F=Farads (F). *Resistance values are in ohms, unless specified otherwise, 1K=1,000 (OHM), 1M= 1,000k (OHM). *The marking (RTL) indicates the retention time is limited for this item. After the discontinuation of this assembly in production, it will no longer be available.
Page 158
FRONT ORNAMENT(R) 20-11 RGK1622A-K FRONT ORNAMENT(L) 20-12 RKF0668-S TRAY DOOR 20-13 VMB3410 BLINDER SPRING 20-14 XTN2+6G SCREW 20-15 VGB0560 PANASONIC BADGE 20-16 RMC0539 DOOR SPRING 20-17 RGL0620-Q LIGHTING PIECE 20-18 RKF0666B-S PANEL DOOR (EG) 20-18 RKF0666C-S PANEL DOOR (EB) 20-18...