Table of Contents CONTENTS PAGE Sections 1. Features 2. Specifications 3. On Screen Display 4. Factory Preset Timings 5. Pin Assignment 6. Main Board I/O Connections 7. Theory of Circuit Operation 8. Waveforms 9. Trouble Shooting 10. Block Diagram 10-1 11.
Page 3
Also, any unauthorized changes or modifications to Amtrak products will void the user’s authority to operate this device. Thus SHARP Will not be held responsible for the product and its safety. CE CERTIFICATION This device complies with the requirements of the EEC directive 89/336/EEC with regard to “Electromagnetic compatibility.”...
Chapter 1 Features 1. Built in TV channel selector for TV viewing 2. Built in HDTV, composite/Component video, HDMI ,ATV out and DTV out ,Audio line out, Audio optical out 3. Built in auto adjust function for automatic adjustment of screen display 4.
Chapter 2 Specification 1. TFT-LCD CHARACTERISTICS Item Specification Supplier Panel AUO_T550QVN03.0 Display Pixels 3840 (H) x 2160 (V) Color Depth 10 bit (8 bit + FRC) (1.07 billion) Pixel Pitch 0.315 (H) x 0.315 (W) 1209.6 (H) x 680.4 (V) Active Screen Size (H x V, mm) Luminance of White 350 nits (typ.)
Page 6
3. Input Connectors 1x Co-axial RF (ATSC/QAM/NTSC) 4x HDMI™ with HDCP 1x Component YPbPr plus Stereo Audio 1x Composite Video plus Stereo Audio (Support/Share via Component YPbPr) 2x USB for FW Update and Photo/Audio/Video Player 1x Ethernet 4. Output Connectors SPDIF Out (Optical Audio), 1x Stereo (R/L) 5.
Page 7
Precaution Please pay attention to the followings when you use this TFT LCD module 1. OPERATING PRECAUTIONS (1) The spike noise causes the mis-operation of circuits. It should be lower than following voltage : V=±200mV (Over and under shoot voltage) (2) Response time depends on the temperature.
Page 8
(2) When the module with protection film attached is stored for a long time, sometimes there remains a very small amount of glue still on the bezel after the protection film is peeled off. (3) You can remove the glue easily. When the glue remains on the bezel surface or its vestige is recognized, please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-hexane.
Chapter 3 On Screen Display 1.1. Specification and explanation of user control panel on the side: (1) POWER (2) MENU (3) CH ︿ (4) CH ﹀ (5) VOL + (6) VOL - (7) INPUT Page 3-1 CONFIDENTIAL – DO NOT COPY File No.
Page 10
i. Power Off When power is off and the Side button is pressed, upon press (not release) of the Side button, the TV is immediately powered on. Long and short key presses do not apply when power is off at the time of the key press. ii.
Page 11
1.2. OSD Adjustment MAIN MENU A. Initial Setup B. Audio Settings C. Picture Settings D. Information E. System Options F. Smart TV Initial Setup A. Language B. Easy Setup C. TV Channel Setup D. Parental Control E. Quick Start Mode F.
Page 12
Language A. English B. French C. Spanish TV Channel Setup A. CH Setup Air/ Cable CH Search Analog & Digital Search Analog Search Start Cancel CH Memory B. Favorite CH Register 1 Data Clear All Data Clear Page 3-4 CONFIDENTIAL – DO NOT COPY File No.
Page 13
Parent Control Secret No. Quick Start Guide Off/ On A. TV Input Setting B. HDMI1 C. HDMI2 D. HDMI3 E. HDMI4 F. COMPONENT Page 3-5 CONFIDENTIAL – DO NOT COPY File No. SG-0000363...
Page 14
G. VIDEO H. HOME Network (DLNA) J. Miracast Advanced A. Digital Audio Out Off/PCM/Bitstream B. Output Select Fixed/Variable C. AQUOS LINK Setup AQUOS LINK Control/ Auto Power On/ Audio Return Channel D. Secret No. E. Reset Page 3-6 CONFIDENTIAL – DO NOT COPY File No.
Page 15
INFORMATION A. Identification B. Digital Caption Info C. Software Update Manual Update [USB Update]/ Auto Update Setting [Off/ On]/ ULI Software Version/ ULI Module Version/ ULI Register/ Firmware Version D. Manual PICTURE SETTING A. AV Mode Standard Movie GAME USER DYNAMIC DYNAMIC (Fixed) B.
Page 16
AUDIO SETTING A. TV Speakers [Off/ On] B. Audio mode [Off/ MOVIE/ News] C. Bass [-12~ +12] D. Treble [-12~ +12] E. Balance [-10~ +10] F. Lip Sync [0~ +5] G. Equalizer Settings 120Hz -12 ~ +12 500Hz -12 ~ +12 1.5KHz -12 ~ +12 5KHz -12 ~ +12...
Page 17
SYSTEM OPTIONS A. Power Control Audio Only[Off / On] No signal Off [Disable/ Enable] No operation Off [Disable/ Enable] Sleep Timer [Off/ 30min/ 60min/ 90min/ 120min] B. Shortcuts SmartCentral Home App Dock View Mode Freeze Change Audio Change CC C. Advanced Menu Design [Program Title Display/ Position/ Caption Setup] Startup Screen [Off/ On]...
Page 18
(tested by All backlight brightness conditions) (1H is height of LCD) ・Photo-detector Center, on Axis 0° more than 4m. (Under CCFL inverter lighting condition ; Illuminance 1000Lux at the photo detector) 1.3.3 Batteries The remote control shall be powered by one user replaceable CR2032 batteries. 1.3.4 Remote control functions CONTROL CODE KEY NAME...
Page 19
K38 FAV APP 1 10001 100001 K39 FAV APP 2 10001 010001 K40 FAV APP 3 10001 110001 K41 Color RED (FAVORITE CH-A) 10000 100011 K42 Color GREEN (FAVORITE CH-B) 10000 010011 K43 Color BLUE (FAVORITE CH-C) 10000 110011 K44 Color YELLOW (FAVORITE CH-D) 10000 001011 K46 CC...
Chapter 7 Theory of Circuit Operation MSD95C0H General Description The MSD95C0H is MStar’s most up-to-date system-on-chip solution for flat panel integrated digital television products. Building on the success of MStar’s advanced technologies, the MSD95C0H hosts the most advanced picture processing engine, MStarACE-PRO4 UC , for all the Experts in various of TV video quality tuning fields to develop the state-of-the-art DTV system.
Page 30
To meet the increasingly popular energy legislative requirements without the use of additional hardware, MSD95C0H has an ultra low power standby mode during which an embedded MCU can act upon standby events and wake up the system as required. Key Features: 1.
Page 31
Transport Stream De-multiplexer .Supports up to five parallel TS interfaces, with or without sync signal .Supports two programmable TS input/output for external CI module .Supports external demodulators .TS data rate is 120Mbit/s for serial and 24MByte/s for parallel .144 general purpose PID filters and 128 section filters for all transport stream de-multiplexer .Supports additional audio/video/PCR filters .Supports TS DMA channel for time-shift .Supports 3DES/DES and AES encryption/decryption...
Page 32
.Profile Level 5 with bitrate up to 135Mbps, the upper limit of level 5 .Supports resolutions for all DVB, ATSC, HDTV, DVD and VCD .Supports resolution up to 4096x2160@30fps .Supports CABAC and CAVLC stream types .Processing of ES and PES streams, extraction and provision of time stamps H.264 MVC Decoder .ITU-T H.264, ISO/IEC 14496-10 video decoding (Main and high profile up to level 4.2) .Supports resolution up to 1080p@60fps...
Page 33
RealMedia Decoder Optional .Supports maximum resolution up to 1080p@30fps .Supports RV8, RV9, RV10 decoders .Supports file formats with RM and RMVB .Supports Picture Re-sampling .Supports in-loop de-block for B-frame .Supports dual stream decoding HEVC (H.265) Decoder .Supports Main/Main-10 profile, level 5.1, high tier .Supports resolution up to 4096x2160@60fps .Supports bitrate upto 110Mbps, the upper limit of level 5 and high-tier.
Page 34
Hardware JPEG Decoder .Supports sequential mode, single scan .Supports both color and grayscale pictures .Following the file header scan the hardware decoder fully handles the decode process .Supports programmable Region of Interest (ROI) .Supports formats: 422/411/420/444/422T .Supports scaling down ratios: 1/2x1/2, 1/4x1/4, 1/8x1/8 .Supports 1280x720@30p VC-1 Video Decoder Optional .Supports SMPTE-421 (WMV video) decoding up to MH@HL...
Page 35
.Built-in audio sampling rate conversion (SRC) .Audio processing for loudspeaker channel, including volume, balance, mute, tone, EQ, virtual stereo/surround and treble/bass controls .Advanced sound processing options available, for example: Dolby 2 , DTS 3 .Supports digital audio format decoding: − MPEG-1, MPEG-2 (Layer I/II), MP3, Dolby Digital (AC-3) Optional , AAC-LC, HE-AAC, WMA, and WMA9 −...
Page 36
.Automatic color calibration Analogue RGB Auto-Configuration & Detection .Auto input signal format and mode detection .Auto-tuning function including phasing, positioning, offset and gain configuration .Sync Detection for H/V Sync DVI/HDCP/HDMI/MHL Compliant Input Ports .Four HDMI/DVI Input ports .HDMI 2.0 Compliant .MStar iSwitch for fast HDMI switching .HDCP 1.4/2.2 Compliant .Up to 600MHz @ 4K2K 60Hz 444 8-bit mode or 422 12-bit mode...
Page 37
.MACE-PRO4 UC Advanced Scaling Engine: − Multi-directional Scaling Technology − High-Tap Filters with Programmable Parameter − De-jagging Support − Video Feather Artifact Detection and Removal − Nonlinear Video Scaling − Dynamic Scaling for RM, VC-1 Optional . MACE-PRO4 UC DTV Video Processing Technology: −...
Page 38
−Supports HDMI 1.4 Deep Color Format −Supports HDMI 1.4 sYCC601/AdobeRGB/AdobeYCC601 Color Formats −Supports BT.2020 Color Space −Supports Enhanced and Seamless Color Mapping for Wide Gamut Panels .Programmable 12-bit RGB gamma CLUT .Top/Bottom,Left-Right and ChessBoard 3D Format Auto-Detection .Supports 2D to 3D conversion Output Interface .Single/Dual link 8/10-bit LVDS output/Mini-LVDS output .8 lane 8/10-bit Vby1 output (configurable width: 2/4/8 lane)
Page 39
CVBS Video Output .Allows CVBS output of digital content to SCART .Supports on-line CVBS bypass output 2D Graphics Engine .Hardware Graphics Engine for responsive interactive applications .Supports point draw, line draw, rectangle draw/fill and text draw .Supports BitBlt, stretch BitBlt, italic Bitblt, Mirror BitBlt and rotate BitBlt .Supports alpha-blending operation .Supports source/destination color key and alpha key .Supports dither...
Page 40
.Impulse-Noise suppression .Integrated deinterleaver RAM for Level 1 J =1 and Level 2 J= 1,2,3.4 .Supports IF/low IF interfaces .I2C repeater for tuner control from backend host controller .2010-A74 compliant DVB-C Demodulator .ITU J.83 Annex A/C DVB-C (EN 300 429)compliant .Supports 1-7.2 M Baud symbol rate ....
Page 41
.support LIF/IF interfaces .Automatic co-channel and adjacent channel interference suppression .CCI and ACI rejection capability .Impulse-noise suppression ISDB-T Demodulator .Compliant with ISDB-T ARIB STD-B31 .Compliant with ISDB-Tsb ARIB STD-B29 .Supports all modes defined in ISDB-T spec .Supports all guard ratios: 1/4, 1/8, 1/16, 1/32 .42ms/channel, excluding AGC time and PLL sync .Support IF/low IF interfaces .Impulse-noise suppression...
Page 42
.Bootable SPI interface with serial flash support .Parallel interface for external parallel eMMC flash (optional) and NAND flash support .Power control module with ultra low power MCU available in standby mode .1286-ball BGA package .Operating Voltages: 1.5V (DDR3), and 3.3V (I/O and analog) MST7410DY FEATURES ...
Page 43
Search range: Big H and V search range to handle fast H/W motion Supports logo detection and protection Supports small object detection and protection Advanced handling for small object, logo rim detection, fade in/out, flash, periodical etc. ...
Page 44
Supports PWM output for scan backlight control One I2C Master Channel and one I2C Slave Channel Supports built-in spread spectrum clock for reducing EMI issue 27x27 BGA Package Operating Voltages: 1.15V, 1.5V and 3.3V Separate OSD Data Path Support ...
Page 45
Audio Amplifier: TAS5707L Page 7-17 CONFIDENTIAL – DO NOT COPY File No. SG-0000361...
Page 46
Page 7-18 CONFIDENTIAL – DO NOT COPY File No. SG-0000361...
Page 51
ITHOUT IDEO AFTER URN ON Start 1. Check R35 be Low ( BL-ON ) 2. Check CE21 be 12V ( Panel Power ) Backlight is good? 1. Check CE21 be 12V ( Panel Power ) 2. Check R199 be Low Panel Power is good Check R615/616 be low Is VB1 correct ?
Page 52
HDMI1,2,3,4 HDMI )IS NOT DISPLAY CORRECTLY Start 1. Check video Input signal 2. Check host’s setting 1. Check P3 & P4 & P5 & P6 connect U28&U11 no data 2. Check the pin18 & 19 of P3 & P4 & P5 & P6 1.
Page 53
TROUBLE OF EDID READING Start Support DDC1/2B 1. HDMI cable ok? Is HDMI DDC OK? 2 .Check signal (P3 & P4 & P5 & P6 pin 15&16 to U28) 3. Check HPD Level ’ THERNET CAN T CONNECT TO NTERNET Start 1.
Chapter 11 How to Enter Factory/Service Mode Enter Factory Menu 1. Let the TV under a input source TV, AV IN, Component or HDMI Not in the Setup Wizard or MMP C. Please ADD, DO NOT Select EXIT while in Factory Mode, MUST select “CLEAR STORAGE”...
Chapter 12 How to update FW Update FW 1. Prepare a USB Flash Stick and format as FAT32 format. 2. Copy the upgrade file“install.img ” into the USB Flash Stick. 3. Unplug the AC cable from the TV, let TV power off. (No AC power) 4.
B/C LBL(PET 50#)Sharp LC-55UB30U Assembly Pull 9LE 193613002500 S/N LBL(Black) 40*8(PET 50#) Assembly Pull 9LE 193614006010 CTN LBL(art paper 80#)(45x45mm)JVC Assembly Pull 9LE 193614006110 CARTON LBL(art paper 80#)(40*60) Sharp Assembly Pull Page 14-1 Confidential- do not copy File No. SG-0000361...
Page 64
12/IS-08A) N.M(SH) USB 2.0 AM to AF UL2725 #28*1P+#28*2C+AEB 9LE 032300000180 Assembly Pull AL65% 3000mm 9LE 098001490010 IR Blaster USB Dongle TRX FOR SHARP LF Assembly Pull REMOTE IR 38KHZ 32KEY GJ221-U W/BATTERY 9LE 098003063230 Assembly Pull FOR SHARP LF 9LE 172500041050 MAC SCREW-MB M4.0*10.0L,BLK-Ni,NYLOK...
Page 65
FRONT BEZEL(LC-55UB30U) Supplier 9LE 170101530010 FRONT BEZEL(PCABS+GF15 FR/T52013)(LC- Supplier TECH LBL(100# PP)(non E-Star)(Dolby 9LE 193616006800 Supplier Plus/WIFI/HDMI)Sharp 9LE 193616006860 ENERGY GUIDE LBL(100# PP)Sharp LC-55UB30U Supplier FOAM PAD 9LE 194715011060 Supplier ASS'Y(PE1210*4.0*0.8t/BLK+AL1210*8.5*0.15t) 9LE 194715011070 FOAM PAD Supplier 9LE 194717001250 Conductive Fabric tape (L15*W34mm)
Page 77
MAVDD_DDR U11A MST7410DY Close to DDR POWER PIN MAVDD_DDR Close to DDR POWER PIN MAVDD_DDR MAVDD_DDR MAB-TMA0 MCD-TMA0 A_DDR3_A0 B_DDR3_A0 MAB-TMA1 MCD-TMA1 Close to DDR POWER PIN Close to DDR POWER PIN A_DDR3_A1 B_DDR3_A1 MAB-TMA2 MCD-TMA2 A_DDR3_A2 B_DDR3_A2 MAB-TMA3 MCD-TMA3 C504 C507 C155...
Page 97
CPU Power Device Power 1.8V CPU Power 0.95V DVDD33 VCC1.8V U27 AP1117EG-13 DVDD33 ADJ/FIX VDDC_CPU 80ohm/6A 80ohm/6A 0805L 0805L R116 SOT223 R382 0/0805 C357 C359 240_F C368 0805L CE34 10uF/10V 0.1uF/16V CE35 0.1uF/16V R112 NC/100 C129 1uF 100uF/16V 0805C 100uF/16V POWER_SW 0603C 0/0805...
Page 98
2015 UHD MSD95C0H+MST7410DY Main Board Scaler : MSD95C0H MEMC : MST7410DY System Power 5V Standby Power DDR3 SDRAM Power 1.5V_ for DDR3 (MIU0,1) PWR_5V USB5V Scaler DDR3 : 6 chips +5VSB VCC5VA VCC5V 80ohm/6A 0805L MEMC DDR3 : 4 chips PWR_5V Del F2 Del R267...
Page 99
1.Modfiy C222~C226 and C235 =470nF 2014.05.05 2.Add C453=120pF capacitor on CVBSOUT nearby chip to avoid EMI 2014.05.08 3.Add U55 MSH6000A Power IC for VDDC_CPU 2014.05.12 4.Modify pg22, pg24 for MSB1240 demodulator, and dual CI application with serial demodulator output. (2014.5/13) 5.Change U55 VDDC_CPU power control by I2C 2014.05.22 6.