Page 4
Metal Part cal return path to the chassis. Any current measured must not exceed 0.5mA. Reverse the instrument power cord plug in the out- ohmmeter let and repeat the test. See Fig. 1-1. Fig. 1-2 Insulation Resistance Test Samsung Electronics...
Page 5
(5) antenna wiring. Always inspect in all areas tinuously and new instructions are issued whenev- for pinched, out-of-place, or frayed wiring, Do not er appropriate. change spacing between a component and the printed-circuit board. Check the AC power cord for damage. Samsung Electronics...
Components identi- fied by shading, by( ) or by ( ) in the circuit dia- gram are important for safety or for the characteris- tics of the unit. Always replace them with the exact replacement components. Samsung Electronics...
(6) Do not remove a replacement ESD device from its protective package until immediately before your are ready to install it.(Most replacement ESD devices are packaged with leads electrically short- ed together by conductive foam, aluminum foil or comparable conductive materials). Samsung Electronics...
32, 44.1, 48kHz Scart(TV) Video(CVBS/RGB), Audio L/R Scart(VCR) Video(CVBS), Audio L/R A/V Output RCA Jack Video(CVBS), Audio L/R Digital Audio Output Optical Size (W x D x H): 381 x 267 x 60 mm Phisical Specification Weight (Net) 3.1 Kg Samsung Electronics...
L/R CH : RCA SCART VCR Input Display Module 10Digits VFD Module Power LED Indicator O(Power on:Green,Standby:Red) O(Power on: None,Standby:Red) IR LED Display AC3 LED Display Type 36-Key Standard 47-Key Standard Color Silver Black Battery Type AAA 2EA AAA 2EA Samsung Electronics...
Page 10
Component Video Cable A/V RCA Cable RF Cable Modem Cable Input Voltage AC 100-240V~,50/60 Hz AC 230V~,50/60 Hz Power Consumption Max.25W Max.30W Size 270 x 200 x 45 mm 381 x 267 x 60 mm Weight 1.2Kg 3.1Kg Samsung Electronics...
Remote Model Standard MF59-00287A Control of DCB-P850Z/XEE Model Standard Batteries for 4301-000115 of DCB-P850Z/XEE Remote Control S.N.A Model Standard MF68-00409A User’s Manual of DCB-P850Z/XEE Model Standard RF Cable AC39-00017A of DCB-P850Z/XEE Model Standard SCART Cable AH39-00043B of DCB-P850Z/XEE Samsung Electronics...
To scan particular channel, select a mode between Auto and Manual. In the manual mode, you can select the channel and PID. To start the software upgrade, press the OK button. Caution : When the receiver is transferring, you must keep a thing intact until transfer is ended. Samsung Electronics...
DCB-P850RS/P850ZS/P853ZS (3 X 8 S) DCB-P850R/P850Z/P853Z (3 X 10 B) ˇ 3 SCREWS DCB-P850RS/P850ZS/P853ZS (3 X 8 S) DCB-P850R/P850Z/P853Z (3 X 10 B) ¨ 3 SCREWS (3 X 8 S) ˆ TOP CABINET Fig. 4-1 Top Cabinet removal Samsung Electronics...
Page 15
Disassembly and Reassembly 4-1-2 Ass’y Hard Disk Removal 1) Remove 4 Screws Œ. 2) Remove Ass’y Hard Disk ´. Œ 4 SCREWS (2.8 X 4 S) ´ ASS’Y HARD DISK Fig. 4-2 Ass’y Hard Disk Removal Samsung Electronics...
Page 16
4-1-3 Main PCB, S.M.P.S PCB Removal 1) Remove 8 Screws Œ. 2) Remove Main PCB ´, S.M.P.S PCB ˇ. Œ 8 SCREWS (3 X 6 S) ˇ S.M.P.S PCB ´ MAIN PCB Fig. 4-3 Main PCB, S.M.P.S PCB Removal Samsung Electronics...
Page 17
Disassembly and Reassembly 4-1-4 Ass’y Front Removal 1) Remove 4 Hooks Œ, ´, ˇ. 2) Remove Ass’y Front ¨. ´ 1 HOOK ¨ ASS’Y FRONT Œ 1 HOOK ˇ 2 HOOKS Fig. 4-4 Ass’y Front Removal Samsung Electronics...
Page 18
1) Remove 3 Screws Œ, ´. 2) Remove Fan ˇ. 3) Remove Chassis Rear ¨. Œ 2 SCREWS (5 X 14 S) ¨ CHASSIS REAR ˇ FAN Œ 1 SCREW (3 X 8 S) Fig. 4-5 Chassis Rear, Fan Removal Samsung Electronics...
Page 19
Disassembly and Reassembly MEMO Samsung Electronics...
If the controller is Check the voltage operating unstably or no of Vcc for SMPS operation,change the PQIZ1 controller Check the Check the shorting at connection at several main power several main power Connect between SMPS and Main Power Samsung Electronics...
Page 21
Change for same spec tuner. from ˇ20pin to ¨28pin. Clock & Data OK? ˇ Clock : 20Pin (TS_CLK) Check serial registers' Correct resistors of condition of TS & control pins. location(R105~R116). No problem ? ¨ Data : 28pin (TS_DATA) Check Decoder "U302". Samsung Electronics...
Page 22
Check ´ CVBS at Video filter(C756,L708, 4pin of U701? C763,C773,R736,C715) Check ˇ CVBS at Check Failure mode of U701 ´ CVBS at 4Pin of U701 36pin of U701? Check Failure mode of J703 ˇ CVBS at 36Pin of U701 Samsung Electronics...
Page 23
Check ˇ CVBS at Check Failure mode of U701 44pin of U701 ´ CVBS at 4pin of U701 Check CVBS at Check R806,R812, ,C809 19pin of Scart Connector ˇ CVBS at 44pin of U701, Check Failure mode of J801 SCART Connector Samsung Electronics...
Page 24
¨ Pin 42,15 Check Open or Short at the circuit Check R/G/B signal at R : R805,R811,C808 Pin ¨15,ˆ11,Ø7 G : R804,R810,C807 of SCART Jack B : R803,R809,C806 ˆ Pin 40,11 Check RGB-Jack Connection (STB°ÍTV). Ø Pin 38,7 Samsung Electronics...
Page 25
Troubleshooting SPDIF Output Missing (Optical) Check +5V Check +5V Drive at Pin2 of J702 Œ Digital Audio signal at R714 Check Failure mode Check Œ Digital Audio U302(STi5100) signal at R714 Check J702 Optical Jack Failure mode Samsung Electronics...
Page 26
Pin28,27 of U701 Failure mode. ˇ Analog Audio output at Pin28,27 of U701 Check ¨ Audio signal at Check U1001 Failure mode and application circuit L706, L705 Check Failure mode of J703(RCA Connector) ¨ Audio signal at L706, L705 Samsung Electronics...
Page 27
Pin33,32 of U701 Failure mode. Check Open or Shot ˇ Analog Audio output at Check ¨ Analog Audio Circuit at C801,R801,C804, Pin33,32 of U701 Signal at L801,L802 L801,R807 Check Failure mode of J801(SCART Connector) ¨ Analog Audio Signal at L801,L802 Samsung Electronics...
Page 28
´ DM(pin3), DP(pin4), J1202 and Flat cale Connection VBUS(pin2) of J1301 (Front Board) Check Open or Short at J1302(USB connector) on Front Board Œ Signal at pin 1, 3 of U502 ´ DM(pin3), DP(pin4), VBUS(pin2) of J1301 (Front Board) Samsung Electronics...
Page 29
= Master ´ U603 Pin11 : ATA Address Check Open or Short at Check the Data Signal at U601,U602,U603,U604,U605 Œ U603,´ U604, and Their Circuit ˇ U605 ˇ U604/U605 Pin2 : ATA Data Check Failure mode of HDD 5-10 Samsung Electronics...
Block Diagrams 8-1 All Block Diagram U301 U302 U401 This Document can not be used without Samsung’s authorization. Samsung Electronics...
Page 44
2x I/F MAFE I/F Transport Steam decoder SmCard Tx/Rx amd SiLabs Central merger DisEqC Audio UARTs SSCs DACs TS0IN TS2IN TS1IN Analog audio ser/par TS2OUT par/D1 out L/R 1394OUT This Document can not be used without Samsung’s authorization. Samsung Electronics...
PCB Diagrams 10-1 Main PCB COMPONENT SIDE U301 B-3 U1001 C-1 U701 E-1 Sti5100 U301 U701 U1001 10-2 Samsung Electronics...
Page 50
ˇ CVBS at Pin 4 of U701 ” U603 Pin1 : ATA Select ¨ CVBS at Pin 36,44 of U701 ’ U603 Pin11 : ATA Address ¨ Ø ˆ∏ ˆ Pin 40 of U701 ˝ U604/U605 Pin2 : ATA Data Samsung Electronics 10-3...
Page 51
PCB Diagrams CONDUCTOR SIDE 10-4 Samsung Electronics...
Œ I2C_CLK ´ I2C_Data ˇ TS CLK ¨ TS DATA ◆ These are the waveforms of DCB-P850R/P850RS/P850Z/P850ZS Caution) There can be some differences (Voltage, Frequency, stc.) among cameras. This Document can not be used without Samsung’s authorization. 11-3 Samsung Electronics...
Schematic Diagrams 11-3 DDR Interface (Main PCB) Sheet 2 of 10 This Document can not be used without Samsung’s authorization. Samsung Electronics 11-4...
Schematic Diagrams 11-4 Flash Interface (Main PCB) Sheet 3 of 10 This Document can not be used without Samsung’s authorization. 11-5 Samsung Electronics...
11-5 TS Interface,USB2.0,JATG (Main PCB) Sheet 4 of 10 Œ USB ◆ These are the waveforms of DCB-P850R/P850RS/P850Z/P850ZS Caution) There can be some differences (Voltage, Frequency, stc.) among cameras. This Document can not be used without Samsung’s authorization. Samsung Electronics 11-6...
Sheet 5 of 10 Œ ATA Address ´ ATA Select ˇ ATA Data ◆ These are the waveforms of DCB-P850R/P850RS/P850Z/P850ZS Caution) There can be some differences (Voltage, Frequency, stc.) among cameras. This Document can not be used without Samsung’s authorization. 11-7 Samsung Electronics...
’ R_1 out ¨ CVBS_1 ˝ CBVS_4 ˆ Audio L, R ◆ These are the waveforms of DCB-P850R/P850RS/P850Z/P850ZS Caution) There can be some differences (Voltage, Frequency, stc.) among cameras. This Document can not be used without Samsung’s authorization. Samsung Electronics 11-8...
Schematic Diagrams 11-8 AV Output(SCART) (Main PCB) Sheet 7 of 10 Video Audio This Document can not be used without Samsung’s authorization. 11-9 Samsung Electronics...
Schematic Diagrams 11-10 S-Card, Power (Main PCB) Sheet 9 of 10 This Document can not be used without Samsung’s authorization. 11-11 Samsung Electronics...
Schematic Diagrams 11-11 Reset,RS232,EEPROM (Main PCB) Sheet 10 of 10 This Document can not be used without Samsung’s authorization. Samsung Electronics 11-12...
The received RF input signal split two ways by splitter for input of two tuners and RF out at rear panel. To boost the divided RF signal, 5V is supplied. 13-1-2 Block Diagram AN IN Booster Tuner in Splitter RF OUT fig. 13-1 Samsung Electronics 13-1...
Function of QAM-Demod block makes the MPEG-2 TS (Transport Stream) by QAM demodulation. TS is consists of D at a [ 0: 7] , Sync, Er r or , Val i d and Cl ock signals. Tuner is controlled by I2C. 13-2-2 Block Diagram fig. 13-2 13-2 Samsung Electronics...
TV out 8K DCache omterface S/PDIF Audio 2x I/F MAFE I/F Transport Steam decoder SmCard Tx/Rx amd SiLabs Central merger DisEqC Audio UARTs SSCs DACs TS0IN TS2IN TS1IN Analog audio ser/par TS2OUT par/D1 out L/R 1394OUT fig. 13-3 Samsung Electronics 13-3...
Page 79
16-bit wide interface. Bus cycle strobe timings can be programmed from 0 to 15 phases for slower peripherals. The FMI output drive of the STi5100 is programmable on a bus-by-bus basis. Support is provided for connection to an ATAPI HDD. 13-4 Samsung Electronics...
Page 80
An internal multiplexor routes this to the stream merger’s upper port, which has an internal by-pass directly to the PTI. D1 header processing and buffering is performed by the PTI. Transport deMUX and D1 processing may not be performed simultaneously. 1) Block diagram: Transport stream merger inputs and outputs fig. 13-4 Samsung Electronics 13-5...
Page 81
When the PTI is required to output a transport stream, it can output the entire transport stream or selected packets filtered by PID. A latency counter is provided to ensure packet timing is preserved. Packet substitution can also be performed. 13-6 Samsung Electronics...
Page 82
• Alpha with pixel (ARGB1555 or ARGB4444, true color mode only). When mixing OSD regions the still picture layer and decoded video are output on the composite outputs (YC and CVBS), component (RGB/YUV) and digital video outputs. The capability for a separate VCR output is also supported. Samsung Electronics 13-7...
Page 83
(S-VHS(Y/C) + CVBS + RGB) or (S-VHS(Y/C)+ CVBS + YUV) or (Y1 + C1 + CVBS1 +C2 + Y2 + CVBS2). The encoder can operate in master mode or in one of several modes where it locks onto incoming sync signals. 13-8 Samsung Electronics...
Page 84
The audio decoder outputs IEC958/IEC1937 formatted CD or PCM audio received from the audio decoder. • 1-channel PCM output interface The PCM output interface outputs PCM audio received from the audio decoder. • Integrated 24-bit stereo audio DAC system • Programmable tone generation for dish alignment Samsung Electronics 13-9...
Page 85
• Fast 2-D unaligned memory-to-memory transfers of graphics and stills, • Real-time stream transfers to and from memory with or without pacing. These channels are suitable for transfers with external peripherals, HDD and for audio and video stream transfers within the STi5100. 13-10 Samsung Electronics...
Page 86
• DiSEqC. 2.0 control support, interface to STMicroelectronics LNBP21 PSU controller or a discrete external solution, • Interface to SiLabs line side device (DAA), • An interrupt level controller, • A low-power/RTC/watchdog controller, • DCU toolset support, • A JTAG/TAP interface. Samsung Electronics 13-11...
If a byte/word program is attempted while VPEN ≤ VPENLK, SR.4 and SR.3 will be set. Successful byte/word programs require that the corresponding block lock-bit be cleared. If a byte/word program is attempted when the corresponding block lock-bit is set, SR.1 and SR.4 will be set. 13-12 Samsung Electronics...
Page 88
If a command other than Write Confirm is written to the device, an “Invalid Command/Sequence” error will be generated and SR.5 and SR.4 will be set. For additional buffer writes, issue another Write to Buffer Setup command and check XSR.7. Samsung Electronics 13-13...
Page 89
Machine Vdtage Switch 64-Mbit: Sixty-four 128-Mbit: One-hundred Address X-Decoder Latch twenty-eight 128-Kbyte Blccks Address Counter fig. 13-6 2) HDD This saves the video files which are received from broadcasting and MP3&JPEG files from external memory (USB Interface). 13-14 Samsung Electronics...
Page 90
• 7.8µs Maximum Average Periodic Refresh Interval • 2.5 V (SSTL_2 compatible) I/O • VDDQ = 2.5 V ± 0.2 V • VDD = 2.5 V ± 0.2 V • P-TFBGA-60-11 package • P-TSOPII-66-1 package • RoHS Compliant Products1) Samsung Electronics 13-15...
Page 91
An auto refresh mode is provided along with a power-saving power-down mode. All inputs are compatible with the JEDEC Standard for SSTL_2. All outputs are SSTL_2, Class II compatible. 13-16 Samsung Electronics...
The available output signals are Y, C, CVBS, R, G and B which are connected to Video/Audio switching control IC (STV6412) through filter circuit. 13-5-1 Block Diagram – Video out. Y-Fiter CVBS C-Fiter CVBS-Fiter STI5100 STV6412 (Video DAC of (Audio/Audio Main Processor) R-Fiter Switch IC) G-Fiter B-Fiter CVBS fig. 13-8 13-18 Samsung Electronics...
The level of analog audio L and R signals is small, so these signals go to amp IC (BA4560). The audio signal output is connected with audio and video switching IC(STV6412). 13-6-1 Block Diagram – Audio Out SPDIF STV6412 STV6412 (Audio DAC of (Vidio AMP) Main Processor) fig. 13-9 Samsung Electronics 13-19...
PIO bits to provide the clock, reset, and I/O functions on the card interface. Smartcard interfaces are supported for the STi5100. This interfaces automatically detects and removes power to the smartcard when smartcard removal is detected. 13-7-1 Block Diagram – Smart Card fig. 13-10 13-20 Samsung Electronics...
STI5100 provides the USB 2.0 Host. This function supports that MP3 and JPEG files save to internal HDD from external USB memory, MP3 Player and DSC. 13-8-1 Block Diagram – USB USBL C6-2P6 STi5100 (USB Interface of Main Processor) VBUS USB_PWR LM3526-H VBUS Controller USB_OVRI fig. 13-11 Samsung Electronics 13-21...
NTSC signal requires slightly less transmission capacity at 168 Mbps. The situation becomes much more acute, when one realises that high definition TV is just around the corner. A High Definition TV (HDTV) picture requires a raw bandwidth exceeding 1 Gbps (1000 Mbps). Samsung Electronics 14-1...
Page 99
AC-3 is a sound encoding/decoding technology developed in 1987 for movie theaters and means an AC-3 bit stream.AC-3 is used synonymously with Dolby Digital nowadays. 14-2 Samsung Electronics...
Page 100
In the past, time shifting was done with a video cassette recorder (VCR) and its timer function, in which the VCR tunes into the appropriate station and records the show onto video tape Samsung Electronics 14-3...
5. 8 : SD High-end Model 6. 5 : 2005 Generation 7. 0 : Basic 3 : Derivation 8. CAS name 1) R : Irdeto 2) Z : Conax 9. None : Black Color : Silver Color 14-4 Samsung Electronics...