Page 2
2000 Matsushita Electric Industrial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law. 1. INTRODUCTION This service manual contains technical information which will allow service personnel to understand and service this model. If the circuit is changed or modified, this information will be followed by supplementary service manual to be filed with original service manual.
2. The Model No. is indicated on the Schematic Diagram and Circuit Board Diagrams as follows. Model No. Indication Mark NV-HS860EG-K/EG-S NV-HS860B-S NV-HS860EC-S NV-HS960EG-S NV-HS960B-S NV-HS960EC-S 2. GERAL DESCRIPTIONS 2.1. SERVICE CAUTION-1 -REPLACING IC7701, IC7703 and/or B7701- When the OSD-Microprocessor IC7701, S-RAM IC7703 and/or Back-up battery B7701 are replaced, the Tape Library data will not be available.Therefore, back up the Tape Library data...
Page 4
STEP2.REPLACE THE IC7701, IC7703 AND/OR B7701 1. Disconnect the AC plug. 2. Remove the C.B.A. with Mechanism unit by referring the Disassembly procedure. 3. Replace the IC7701, IC7703 and/or B7701. STEP3.RESTORE THE TAPE LIBRARY DATA 1. Using the Remote controller: A.
Page 5
PROCEDURE F.I.P. DISPLAY Turn on the Service Mode "Turn the Shuttle Ring to FF"*1 and press the EJECT key simultaneously for more than 3 seconds. Activate the Service Mode 2 "Turn the Shuttle Ring to FF"*1 and press the EJECT key in twice. Activate the Entering Mode.
Page 6
Model No. Model Option Option Option Code Code 1 Code 2 Code 3 NV-HS860EG NV-HS860EC NV-HS860B NV-HS960EG NV-HS960EC NV-HS960B Fig.S2 Model Code & Option Code NOTE: Since all electrical adjustments data is still not available, perform the Electrical Adjustment continuously. - Turn on the Service Mode by: / (NV-HS960 series) / Rotating the Shuttle Ring to FF side and press the EJECT key simultaneously for 3 seconds.
Page 8
2. UPPER CYLINDER DISASSEMBLY A. Remove the Top Panel. B. Remove the screw (A) and Earth Plate. C. Move the lock pinch to the left side in order to release the cylinder lock. D. Keep turning the Upper cylinder clockwise and / counterclockwise alternately and remove the Upper cylinder.
2.2.5. FLAT CARD CABLE INSTALLATION When installing the Flat Card Cable on the connector, install the Flat Card Cable with the cable contacts facing the connector contacts. Fig. S8 2.3. REMOVAL OF CASSETTE TAPE There are 2 ways to remove a cassette tape. 1.
Page 10
2.4. INTRODUCTION OF VIDEO HEAD CLEANING CASSETTE / (POLISHING TYPE) 1. We are pleased to introduce Panasonic Video Head Cleaning Cassette, VFK0923FT [for service purposes] and VFK0923FSE [for end users] for all VHS/SVHS VCP and VCR. 2. These cleaning cassettes are exclusive removing the hard and sticky clogging on video heads.
Page 11
VFK0923FT (For Service usage) Type of Cassette Full VHS Cassette Cleaning Time 10 Seconds/Time Tape Length 20 m Usability in a Path 180 Times VFK0923FSE (For end users) Type of Cassette Full VHS Cassette Cleaning Time 10 Seconds/Time Tape Length 3.34 m Usability in a Path 30 Times...
VFK0923FSE (For end users) Note: The tape material itself is the same in both types. 2.5. CAUTION FOR AC MAINS LEAD (NV-HS860B-S, HS960B-S) 2.6. HOW TO REPLACE THE LITHIUM BATTERY 2.6.1. Backup Battery B7701 This VTR equipped with the Backup Battery (B7701) to backup the following memorized data in the S-RAM IC7703.
Page 13
CAUTION: The lithium battery is a critical component (Type No.: CR2354-1GUF Manufactured by Panasonic.) / It must never be subjected to excessive heat or discharge. / It must therefore only be fitted in equipment designed specifically for its use. / Replacement batteries must be of the same type and manufacture.
3. ADJUSTMENT PROCEDURES 3.1. DISASSEMBLY METHOD 3.1.1. DISASSEMBLY FLOW CHART This flow chart indicates disassembly steps of the cabinet parts and the circuit boards in order to find the necessary items for servicing. When reassembling, perform the steps in the reverse order. Fig.
Page 15
2. REMOVAL OF THE FRONT PANEL UNIT Pull out JOG & SHUTTLE UNIT & JOG DIAL (HS960 Series only) Unlock 7 Tabs (B) Fig. D3 3. REMOVAL OF THE POWER C.B.A. Disconnect Bridge Connector (C) Unlock 6 Tabs (D) Fig. D4...
Page 16
COUTIONS: Please pay an attention to disconnect the connector (P1001- P1102) which connected between Main C.B.A. and Power supply unit as shown below. Fig. D5 As above drawing, disconnect the connector by SCREW DRIVER from the direction (A). / Do not disconnect from direction (B) because it is possibility to damage the parts located by the connector.
5. REMOVAL OF THE MECHANISM UNIT Remove 3 Screws (G) Remove 2 Screws (H) Note: Keep pressing 2 stoppers on Cassette Holder Plate and Press Cassette Holder Plate to the rear. Fig. D7 6. REMOVAL OF THE MAIN C.B.A. Disconnect Bridge Connector (C) Remove Screw (I)
7. SERVICING POSITION Fig. D9 3.2. MECHANICAL ADJUSTMENT PROCEDURES Refer to the Service Manual for Z-Mechanism Chassis. / (Order No. VRD9802005C2) 3.3. ELECTRICAL ADJUSTMENT PROCEDURES 3.3.1. TEST EQUIPMENT The following equipment is required for Electrical Adjustments. 1. Dual-Trace Oscilloscope - Voltage Range:0.005-5V/div - Frequency Range:DC-35MHz - Probes: 10:1/1:1 2.
Page 19
- Probes:1:1 3. Universal Counter 4. Digital Volt Meter (D.V.M.) 5. Video Sweep Generator 6. Sine-wave Generator 7. Video Pattern Generator 8. Monitor TV 9. DC Power Supply 10. VHS/S-VHS Blank Tape 11. VHS Alignment Tape - Parts No.:VFJ8125H3F(PAL) 3.3.2. VCR SETTING When no indication in the procedure, set each selector as follows.
Page 20
ITEM ADJ. MODE INPUT TAPE M. EQ. SPEC. REMARKS Refer to procedure as PLAYBACK --- ALIGNMENT Fig.E5. SHIFTER TAPE ADJUSTMENT (PAL) 1. VIDEO OUT must be 75 ohm VIDEO EE TP3002 VR3004 STOP PAL / 2.0+-0.1 (Vp- OSCILLOSCOPE COLOUR LEVEL (See Fig.
Page 21
Fig. E1 Fig. E2 Fig. E3 CONDITION:BURST SIGNAL 75ohm TERMINATED Fig. E4 3.3.4. PG SHIFTER ADJUSTMENT / (AUTOMATIC) PROCEDURES FIP Display "Turn the Shuttle Ring to FF"*1 and Press EJECT key simultaneously for 3 seconds. "Turn the Shuttle Ring to FF"*1 and Press EJECT key simultaneously more twice.
Page 22
PROCEDURES FIP Display When this Adjustment is terminated, the following operation will be activated. Adjustment completed: The tape will be ejected. Adjustment incompleted: "F2*" is indicated on the FIP.Check the Servo/ System Control circuit and Cylinder Unit. To release Service Mode, "turn the Shuttle Ring to FF"*1 and Press EJECT key simultaneously 6 times until the normal indication on the FIP.
Page 23
PROCEDURES FIP Display Adjust the Frequency response by pressing the "2" (increase) and/or "8" (decrease) key on the Remote Controller. (Refer to Fig.E4) Spec. SP/LP:0+-1dB(90-110%) To release Service Mode, "Turn the Shuttle Ring to FF"*1 and press the EJECT key simultaneously 6 times until it would be a normal indication.
9.9. HEAD AMP SCHEMATIC DIAGRAM 9.10. TV DEMODULATOR PACK SCHEMATIC DIAGRAM 9.11. DECODER PACK SCHEMATIC DIAGRAM (EG) 9.12. NICAM DECODER PACK SCHEMATIC DIAGRAM (B/EC) 9.13. AV FRONT SCHEMATIC DIAGRAM 9.14. FRONT SWITCH SCHEMATIC DIAGRAM 10. CIRCUIT BOARD ASSEMBLIES 10.1. POWER C.B.A. 10.2.
Page 34
4.43 NTSC L BILINGUAL 443NT [L] BILINGUAL L A. COMP BIL [L] AUDIO COMPONENT SIGNAL BILINGUAL H BIL. [H] A. COMPO AUDIO COMPONENT SIGNAL BILINGUAL L AUDIO DUBBING PAUSE L BIL/M1 [L] A. D.P [L] AUDIO DUBBING PAUSE L BS CLOCK A.
Page 35
CYL GND CYLINDER GND FULL. E. 12V FULL ERASE 12V DELAIED FM RECORDING H D.F.M. REC [H] GND (ANALOG) GND [A] DELAIED FM RECORDING L D. FM REC [L] GND (TUNER) GND [TU] D. GND GND/NON SW 12V DIGITAL GND GND/N.
Page 36
POWER OFF H LINE IN [R] LINE INPUT (R) P-OFF [H] POWER OFF L LINE OUT [L] LINE OUTPUT (L) P-OFF [L] LINE OUT [R] LINE OUTPUT (R) P. FAIL POWER FAILURE DETECT LP H POWER OFF H LP [H] P.
Page 37
SYSTEM CONTROL 5V RF OUT RF OUTPUT SYSCON 5V SYSTEM SW RF Y RF LUMINANCE SIGNAL SYSTEM TAKE-UP PHOTO TRANSISTOR RF. Y. IN RF LUMINANCE SIGNAL INPUT T-PHOTO TAKE-UP REEL PULSE RF. Y. OUT RF LUMINANCE SIGNAL OUTPUT T-RL. PLS TIMER BUS CLOCK ROTAR.
Page 38
VIDEO MAIN SIGNAL PATH IN REC MODE AUDIO MAIN SIGNAL PATH IN REC MODE VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE AUDIO MAIN SIGNAL PATH IN PLAYBACK MODE <A-LINE> <A-LINE> <A-LINE> (A34) (A32) (A33) (A35) (A36) (A37) (A30) (A31) (A29) R4520 R4507 QR4501...
Page 39
<A-LINE> <A-LINE> (A55) N SW 5V (1) (A52) (A53) (A54) (A55) (A5) (A60) D6702 (A6) N SW 5V (2) MA151WK (RF) BW (H) (A29) (A20) CAL (H) L7601 (A12) YC VIN/YIN C7601 TU7601 (A23) 6V100 YC C OUT K7610 K7609 K7603 K7607 ENG47307G1: (A,C,D,F)
Page 40
VIDEO MAIN SIGNAL PATH IN REC MODE AUDIO MAIN SIGNAL PATH IN REC MODE K6502 (SAT IR LED DRIVE) S6502 R6513 EVQ11L07B (D,E,F) Q6502 4300 D TV REC 2SD973 13.0 R6508 R6510 R6511 R6512 8200 5600 (SAT IR DRIVE) R6522 Q6501 D6503 2SB709A...
Page 41
AUDIO MAIN SIGNAL PATH IN REC MODE AUDIO MAIN SIGNAL PATH IN PLAYBACK MODE IC4501 JK6501 (AV FRONT) AUDIO P6501 P7502 IN (R) SYS IIC DATA TO/FROM SELECT SW CONTROL IIC BUS SYSTEM MUTE CONTROL INTERFACE VOLUME CONTROL CONTROL SYS IIC CLOCK &...
Page 42
IC6001 CAPSTAN CAP TL IC0201 (CAPSTAN MOTOR DRIVE) (SYSTEM CONTROL/SERVO IC) IC7501 MOTOR DP7501 TL2503 L0201 TL0201 MOTOR DIFFERENTIAL TORQUE P0201 P2501 CURRENT 16MHz IN DRIVE AMPRIFIER CONTROL LIMIT TIMER DISPLAY X6001 CAPSTAN P0201 P2501 16MHz OUT ERROR TORQUE 32KHz IN POSITION CAPSTAN X6002...
Page 43
VIDEO MAIN SIGNAL PATH IN REC MODE VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE IC3001 R (26um) JK6502 CPN L P6501 P7502 L'(49um) IC3201 C IN P6501 P7502 P502 P3002 S-VIDEO S-ET P501 Y IN P6501 P7502 REC EO P502 P3002 P501 JK6501...
Page 44
S-VHS DET H REC C VR3002 FILTER QR3303 IC3301 FROM SYSTEM CONTROL & SERVO Q3301 SECTION 76 REC Y ROTARY SW Q3302 FILTER 78 REC C HASW1 H A SW Q3303 REC H 83 Y OUT HASW26U Q3304 ART V/H/N 65 C OUT C IN RSDA...
Page 45
AV FRONT C.B.A. Transistor Q6501 Parts No. Model No. Mark Q6502 VEP04762A NV-HS960EG-S Transistor & Resistor NV-HS960B-S NV-HS960EC-S QR6501 VEP04762B NV-HS860EG-K Connector NV-HS860EG-S NV-HS860B-S P6501 NV-HS860EC-S ADDRESS INFORMATION EJECT POWER S-VIDEO IN S-VHS/ET A.DUB D TV REC AUDIO AUDIO IN (R)
Page 46
Parts No. Model No. Mark VEP07A16A NV-HS860EG-K NV-HS860EG-S NV-HS960EG-S...
Page 47
Parts No. Model No. Mark VEP07A23A NV-HS860EG-K NV-HS860EG-S NV-HS860EC-S NV-HS960EG-S NV-HS960EC-S VEP07A23J NV-HS860B-S NV-HS960B-S (B,E) (B,E)
Page 48
Parts No. Model No. Mark VEP06D78A NV-HS960EG-S NV-HS960B-S NV-HS960EC-S (D,E,F) STOP VEP06D78B NV-HS860EG-K JOG SHUTTLE NV-HS860EG-S NV-HS860B-S PLAY (D,E,F) NV-HS860EC-S PAUSE FRONT SW C.B.A. Connector (A,B,C) (A,B,C) P6301 INTRO-JET SCAN ADDRESS INFORMATION (D,E,F) CH UP CH DOWN (A,B,C) (D,E,F) (A,B,C)
Page 49
HEAD AMP C.B.A. Parts No. Model No. Mark VEP05392A NV-HS960EG-S Transistor NV-HS960B-S Q501 NV-HS960EC-S Q502 VEP05392B NV-HS860EG-K Transistor & Resistor NV-HS860EG-S NV-HS860B-S QR551 NV-HS860EC-S Integrated Circuit IC501 IC551 Connector P501 P502 P503 ADDRESS INFORMATION (D,E,F) (A,B,C)
Page 50
Parts No. Model No. Mark VEP03F50A NV-HS960EG-S NV-HS960B-S NV-HS960EC-S VEP03F50B NV-HS860EG-K NV-HS860EG-S NV-HS860B-S NV-HS860EC-S INPUT/OUTPUT PACK C.B.A. Transistor Q3901 (D,E,F) Q3902 Q3903 (D,E,F) Q3905 (D,E,F) Transistor & Resistor (A,B,C) QR3902 Integrated Circuit IC3901 IC3902 IC3903 Test Point TP3002 TP3003 (D,E,F)
Page 51
WHEN REPLACING ANY OF THESE COMPONENTS. REF. NO. 3000 SERIES USE ONLY THE SAME TYPE. Parts No. Model No. Mark VEP06D77A NV-HS960EG-S (D.E.F) VEP06D77B NV-HS960B-S VEP06D77C NV-HS960EC-S VEP06D77E NV-HS860EG-K NV-HS860EG-S VEP06D77F NV-HS860B-S VEP06D77G NV-HS860EC-S MAIN C.B.A. Transistor QR6003 Q1001 QR6701 Q1002 QR6702 (B.E) (D.E.F)
Page 52
Parts No. Model No. Mark VEP07A18A NV-HS860B-S NV-HS960B-S VEP07A18J NV-HS860EC-S NV-HS960EC-S (B,E) (C,F)
Page 54
POWER C.B.A. Transistor Q1200 Integrated Circuit IC1150 IC1200 Connector CAUTION THESTRIPED FRAME INDICATES THE PRIMARY CIRCUIT TO IMPORTANT SAFETY NOTICE: P1101 DISTINGUISH THE PRIMARY FROM THE SECONDARY CIRCUIT. COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS P1103 PAY ATTENTION NOT TO RECEIVE AN ELECTRIC SHOCK FOR SAFETY.
Page 56
R0206 (FG HEAD) R0212 R0213 Q0203 P0201 Q0202 IC0201 R0207 CURR LIMIT (CAPSTAN MOTOR DRIVE) HOLE HOLE CAP ET SENSOR SENSOR CAP R/F RCC SET CAP FG1 GND (FG) Q0201 C0201 R0210 SW 5V (1) GND (MOTOR) D0203 TL0204 TL0202 TL0203 LOAD MOTOR (-) LOAD MOTOR (+)
Page 57
If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local Panasonic Dealer. IF THE FITTED MOULDED PLUG IS UNSUITABLE TYPE B FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY.
Page 61
VIDEO MAIN SIGNAL PATH IN REC MODE AUDIO MAIN SIGNAL PATH IN REC MODE VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE AUDIO MAIN SIGNAL PATH IN PLAYBACK MODE (D,E,F) IC501 AN3370K OUTPUT DRIVE 0(6.3) 0(3.4) 0(6.3) 0(1.3) 0 0(6.3) 0(12.4) 0(6.3) IC551 AN3328S C503...
Page 67
TO SERIAL INF CLAMP Ext. Control SERIAL CONTROL 75DR Ext. Control MENT CLAMP CLAMP V REF 75DR CLAMP Ext. Control Ext. Control BUFF CLAMP CLAMP...
Page 68
V REF. I REF. A GND LPF-PNR(R CH) LPF-PNR(L CH) TU(L) MODEM TU(R) NORMAL SELECT SWITCH E2(L) E2(R) MODEM TU(L),(R) DECODER E1(L),(R) SELECT SWITCH V5 OUT MUTE OUTPUT SELECT ENVELOPE SWITCH Hi-Fi DET. D.O.C LINE SELECT SWITCH MUTE CTL E2(L),(R) IIC BUS SELECT SW CTL INTERFACE...
Page 70
1Vp-p 0.5Vp-p CLAMP R CLAMP G CLAMP B VREG CONT SYNC CONT CONT C.SYNC MATRIX SW V NTSC APC SW BURST CLAMP ADD R (Y : 6dB) NTSC : OFF AMP 2 HPF 2 CLAMP BURST ADDd BPFd ADD B MIXd AMP 1 HPF 1...
Page 71
VIDEO MAIN SIGNAL PATH IN REC MODE AUDIO MAIN SIGNAL PATH IN REC MODE VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE AUDIO MAIN SIGNAL PATH IN PLAYBACK MODE <A-LINE> <A-LINE> C4904 (DECODER) (A11) (A27) (A12) (A28) (A1) (A3) (A2) 470P JK3905 VJS1470 JK3907...
Page 75
THE STRIPED FRAME INDICATES THE PRIMARY CIRCUIT TO DISTINGUISH THE PRIMARY CAUTION FROM THE SECONDARY CIRCUIT. IP1230 C1232 100P PAY ATTENTION NOT TO RECEIVE AN ELECTRIC SHOCK DURING REPAIR AND SERVICE OF L1230 D1230 100u ERA22-04 THE PRODUCTS. T1150 ETE28K121AZ C1230 C1231 P1102...
Page 77
SYSTEM CONTROL & SERVO ICs DC VOLTAGE CHART (SP MODE) Ref.No. IC1001 IC2501 SHUTTLE 1 MODE S-VHS ET CH SAT CVC VCR XP EP LP SP ON OFF SHUTTLE 2 STOP 15.9 14.1 SHUTTLE 3 REMAIN PLAY 15.4 14.1 R7504 SHUTTLE 4 JOG 1 15.4...
Page 78
VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE R3711 PS3751 SW 5V R3755 C3717 FSC OUT R3751 IC3712 TO TBC PACK (OSC) TC7SET04F D GND D GND IC3711 PP3751 (D-1) Q3751 R3710 D GND TC7SU04FT85L 2SC2295-TX X3751 C3752 VSX0066-C 270P R3753 4700 (BUFFER) Q3752...
Page 79
VIDEO MAIN SIGNAL PATH IN REC MODE AUDIO MAIN SIGNAL PATH IN REC MODE CYLINDER SERVO PHASE LOOP VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE AUDIO MAIN SIGNAL PATH IN PLAYBACK MODE <A-LINE> <A-LINE> (A7) (A8) (A9) (A10) (A11) (A12) (A4) (A5) (A13)
Page 80
<A-LINE> YC Y OUT (A7) (A11) (A22) (A1) (A15) (A9) (A23) (A12) (A24) (A27) (A13) TBC PACK PP3751 SW 5V PB GND K3012 TW3001 FSC OUT K3015 K3007 TO FSC PACK FL3301 PB/REC Y+C PS3751 (E-1) ELKTT221AA QR3002 R3330 PP3503 UN221L Y OUT 4.7(0)
12.1. MECHANICAL REPLACEMENT PARTS LIST 12.1.1. CHASSIS PARTS LIST Ref. No. Part No. Part Name & Description Remarks 1 (1) VEG1547 CYLINDER UNIT NV-HS860EC-S/EG-S/EG-K/B- 1 (1) VEG1548 CYLINDER UNIT NV-HS960EC-S/EG-S/B-S 2 (1) VXP2049 UPPER CYLINDER UNIT NV-HS860EC-S/EG-S/EG-K/B- 2 (1) VXP2050 UPPER CYLINDER UNIT NV-HS960EC-S/EG-S/B-S 3 (1)
Page 88
Ref. No. Part No. Part Name & Description Remarks 51 (1) VXP2035 CENTRE CLUTHCH UNIT NV-HS860EC-S/EG-S/EG-K/B- 51 (1) VXP2053 CENTRE CLUTHCH UNIT NV-HS960EC-S/EG-S/B-S 53 (1) VXL2783 REV ARM UNIT NV-HS960EC-S/EG-S/B-S 54 (1) VML3276 IDLER POSITIONING ARM NV-HS960EC-S/EG-S/B-S 60 (1) VMA9516 TOP PLATE 61 (1) VMB3047...
Page 89
Part No. Part Name & Description Remarks 101 (2) VGM1641 TOP PANEL NV-HS860B-S/EC-S/EG-S, / NV -HS960B-S/EC-S/EG-S 101 (2) VGM1555 TOP PANEL NV-HS860EG-K 102 (2) VYP7898 FRONT PANEL UNIT NV-HS960EG-S 102 (2) VYP7900 FRONT PANEL UNIT NV-HS960EC-S 102 (2) VYP7901 FRONT PANEL UNIT...
Page 90
215 (3) VPG0F78 PACKING CASE NV-HS960EC-S 215 (3) VPG0F79 PACKING CASE NV-HS960B-S 215 (3) VPG0G02 PACKING CASE NV-HS860EG-K SERVICE FIXTURES & TOOLS VFJ8125H3F VHS ALIGNMENT TAPE (PAL) VFK0335 RETAINING RING REMOVER (3mm/4mm) 1 VFK0329 POST ADJUSTMENT SCREWDRIVER VFK0326 HEX WRENCH SET...
Ref. No. Part No. Part Name & Description Remarks VFK0132 BACK TENSION METER VFK27 HEAD CLEANING STICK VFK1024 MOLYTONE GREASE VFK0330 FINE ADJUSTMENT GEAR DRIVER VFK2744 16P EXTENSION CABLE MAIN - POWER VFK1301 SILICONE GREASE VFK1567 15P EXTENSION CABLE PP7703-PS7703,PP7702- PS7702, / PP7701- PS7701,PP3904-PS3904 VFK1568...
Page 92
Ref. No. Part No. Part Name & Description Remarks VEP07A18A NICAM DECODER PACK C.B.A. (RTL) NV-HS860B-S,NV-HS960B-S INCLUDED IN MAIN C.B.A.(VEP06D77F/ VEP07A23A TV DEMODULATOR PACK C.B.A. (RTL) NV-HS860EG-S/EG-K/EC-S,NV- HS960EG-S/EC-S INCLUDED IN MAIN C.B.A.(VEP06D77E/ G/A/C) VEP07A23J TV DEMODULATOR PACK C.B.A. (RTL) NV-HS860B-S,NV-HS960B-S INCLUDED IN MAIN C.B.A.(VEP06D77F/ VEP03F50B INPUT/OUTPUT C.B.A.
Page 93
Ref. No. Part No. Part Name & Description Remarks VEP06D77G MAIN C.B.A. (RTL) NV-HS860EC-S VEP06D77F MAIN C.B.A. (RTL) NV-HS860B-S C0701 ECUM1C105ZFN C.CAPACITOR CH 16V 1U F1J1C105A063 C0702 ECUX1H102KBV C.CAPACITOR CH 50V 1000P C0703 ECUM1A105KBN C.CAPACITOR CH 10V 1U F1J1A1050002 C0704 ECUM1E333KBN C.CAPACITOR CH 25V 0.033U C0706...