Related Manuals for Bosch CS 550
Summary of Contents for Bosch CS 550
- Page 1 All manuals and user guides at all-guides.com CS 550/150RC Spreader Joystick Controller Operator Manual...
-
Page 2: Table Of Contents
1 1 1 1 8 8 8 8 Bosch Rexroth Canada Corp. reserves the right to revise this information at any time and for any reason and reserves the right to make changes at any time, without notice or obligation, to any of the information contained in this piece of literature. -
Page 3: Panel Controls
All manuals and user guides at all-guides.com 3/18 Panel Controls Turn knobs clockwise to increase. Bosch Rexroth Canada ı 07.22.2013 ı Revision 2.0... - Page 4 Spinner Label Solid Name Liquid Name Spread Width % Gate Mode/Solid Rate Liquid Rate Spinner Setpoint Gate Position/Conv Set. Liquid Setpoint Spinner Mode Conveyor Mode Liquid Mode Pause Button Blast Button Reverse Button Bosch Rexroth Canada ı 07.22.2013 ı Revision 2.0...
-
Page 5: Screen Controls
Press the Blast button to increase the spreading output, and press again to resume regular rate. 3.3 Reverse Press and hold the Reverse button to change the direction of the Auger (an optional feature to dislodge obstructions). Release the button to resume spreading. Bosch Rexroth Canada ı 07.22.2013 ı Revision 2.0... -
Page 6: Change Solid Material
3.6 Manual Gate Adjustment For Manual Gate operation ONLY. Press the Gate Position Number to select the gate adjustment mode. Use the up and down arrows to adjust. Bosch Rexroth Canada ı 07.22.2013 ı Revision 2.0... -
Page 7: Error Messages
‘Gear ‘Gear ‘Gear’ ’ ’ ’ symbol to display most recent error messages. If a hydraulic pressure&temperature sensor is connected both readings will be displayed on the bottom right of the screen. Bosch Rexroth Canada ı 07.22.2013 ı Revision 2.0... -
Page 8: Unloading - Unload Symbol
‘ ‘ ‘ ‘ Unload Unload’ ’ ’ ’ symbol to enter into unload mode. (Note: The vehicle must be Unload Unload stationary.) Turn the dials until the desired speed is achieved. Press the symbol again Bosch Rexroth Canada ı 07.22.2013 ı Revision 2.0... -
Page 9: Data Retrieval/Clear Trip Summary - Usb Symbol
Bright/Vol’ ’ ’ ’ symbol to enter into adjustment mode, volume or bright. Press Bright/Vol Bright/Vol again to toggle the other mode. Use the up and down arrows to adjust (only adjustable with vehicle stationary). Bosch Rexroth Canada ı 07.22.2013 ı Revision 2.0... -
Page 10: Manual Hydraulic Gate Adjustment - Cylinder Symbol
4.6 Programming Mode Press the ‘Lock’ ‘Lock’ ‘Lock’ ‘Lock’ symbol to enter into programming mode. (Note: A valid ‘PROGRAMMING KEY’ must be inserted into the USB port.) See Calibration Manual for programming details. Bosch Rexroth Canada ı 07.22.2013 ı Revision 2.0... -
Page 11: Joystick Control
Screen flips when the Deadman Trigger is pressed. When the trigger is released, the screen reverts back to the spreader layout. Note: The joystick will only operate while the Deadman Trigger is pulled. The default spreader or joystick screen is selectable on USER setup screen. Bosch Rexroth Canada ı 07.22.2013 ı Revision 2.0... -
Page 12: Anti Ice Mode
Use the dial on the right to select the desired liquid flow rate. The reverse button is de-activated. 6.2 Single Boom Use the upper right arrows to select the desired liquid flow rate. Bosch Rexroth Canada ı 07.22.2013 ı Revision 2.0... -
Page 13: Pattern Mode
Use the controls on the top right of the screen to control the Air Gate. When vehicle is stationary click on left or right button to toggle between two materials, and automatically set the operation gate to the calibrated gate for the material selected. Bosch Rexroth Canada ı 07.22.2013 ı Revision 2.0... - Page 14 Use the controls on the top right of the screen to control the Cross Conveyors. Select left or right with the circular buttons. Use the up and down arrows to adjust the speed. Bosch Rexroth Canada ı 07.22.2013 ı Revision 2.0...
- Page 15 Load material, check sensor ERROR NO LIQ DETECT Load material, check sensor ERROR NO GROUNDSPEED Check cable/sensor ERROR NO CONVEYOR Check cable/sensor ERROR NO LIQUID Check cable/sensor ERROR NO DEICE Check cable/sensor Bosch Rexroth Canada ı 07.22.2013 ı Revision 2.0...
- Page 16 Check conveyor sensor, and calibrate again PREWET PULSES/GAL TOO LOW Check prewet sensor, and calibrate again PREWET PULSES/GAL TOO HIGH Check prewet sensor, and calibrate again ANTI-ICING PULSES/GAL TOO LOW Check anti-icing sensor, and calibrate again Bosch Rexroth Canada ı 07.22.2013 ı Revision 2.0...
- Page 17 Range between Joy2 Min and Max too small REQUIRED CONV RPM TOO HIGH Setpoints too high, incorrect wt/rev REQUIRED PREWET FLOW TOO HIGH 69 Setpoints too high, incorrect pulses/gallon REQUIRED ANTI-ICING FLOW TOO HI Setpoints too high, incorrect pulses/gallon Bosch Rexroth Canada ı 07.22.2013 ı Revision 2.0...
- Page 18 If the glass chips or cracks, discontinue use and contact Bosch Rexroth Canada to have it replaced - do not touch or attempt to remove the broken glass. Any misuse/abuse causing damage, whether intended or not, will become the sole responsibility of the owner/buyer which will render the warranty of this product, void.