Makita GA007G Instruction Manual
Cordless angle grinder
Hide thumbs
Also See for GA007G:
- Instruction manual (161 pages) ,
- Instruction manual (100 pages) ,
- Instruction manual (53 pages)
Related Manuals for Makita GA007G
Summary of Contents for Makita GA007G
- Page 1 INSTRUCTION MANUAL Cordless Angle Grinder GA003G GA004G GA005G GA006G GA007G GA008G Read before use.
-
Page 2: Specifications
SPECIFICATIONS Model: GA003G GA004G GA005G GA006G GA007G GA008G Wheel diameter 100 mm 115 mm 125 mm 100mm 115 mm 125 mm (4″) (4-1/2″) (5″) (4″) (4-1/2″) (5″) Max. wheel thickness 6.4 mm 7.2 mm 6.4 mm 7.2 mm Spindle thread M14 or 5/8″... - Page 3 Model Vibration emission (a ) : (m/s ) Uncertainty (K) : (m/s GA003G GA004G GA005G GA006G GA007G GA008G Work mode: surface grinding with anti vibration side grip Model Vibration emission (a ) : (m/s ) Uncertainty (K) : (m/s GA003G...
-
Page 4: Ec Declaration Of Conformity
WARNING: The vibration emission during actual use of the power tool can differ from the declared value(s) depending on the ways in which the tool is used especially what kind of workpiece is processed. WARNING: Be sure to identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time). - Page 5 Always wear protective goggles to protect When using the tool, do not wear cloth work your eyes from injury when using power tools. gloves which may be entangled. The entangle- The goggles must comply with ANSI Z87.1 in ment of cloth work gloves in the moving parts may the USA, EN 166 in Europe, or AS/NZS 1336 result in personal injury.
- Page 6 Do not use accessories which are not specifi- 13. Regularly clean the power tool’s air vents. The cally designed and recommended by the tool motor’s fan will draw the dust inside the housing manufacturer. Just because the accessory can and excessive accumulation of powdered metal be attached to your power tool, it does not assure may cause electrical hazards.
- Page 7 Wheels must be used only for recommended If the use of a guard is recommended for wire applications. For example: do not grind with the brushing, do not allow any interference of the side of cut-off wheel. Abrasive cut-off wheels are wire wheel or brush with the guard.
- Page 8 It will nails, coins, etc. also void the Makita warranty for the Makita tool and Do not expose battery cartridge to water charger. or rain.
-
Page 9: Functional Description
Indicating the remaining battery FUNCTIONAL capacity DESCRIPTION Press the check button on the battery cartridge to indi- cate the remaining battery capacity. The indicator lamps CAUTION: Always be sure that the tool is light up for a few seconds. switched off and the battery cartridge is removed before adjusting or checking function on the tool. -
Page 10: Overheat Protection
Overheat protection When the tool/battery is overheated, the tool stops automatically. Let the tool cool down before turning the tool on again. Overdischarge protection When the battery capacity is not enough, the tool stops automatically. In this case, remove the battery from the tool and charge the battery. - Page 11 Adjusting angle of wheel guard WARNING: Make sure that the wheel guard is securely locked by the lock lever with one of the holes on the wheel guard. The angle of the wheel guard can be adjusted by rotating the wheel guard with pushing it down while pushing the lock lever.
- Page 12 Installing or removing abrasive disc Optional accessory NOTE: Use sander accessories specified in this man- ual. These must be purchased separately. For 100 mm (4″) model ► 1. Lock nut 2. Depressed center wheel 3. Inner flange 4. Mounting part To tighten the lock nut, press the shaft lock firmly so that the spindle cannot revolve, then use the lock nut wrench and securely tighten clockwise.
- Page 13 Mount inner flange, abrasive wheel and Ezynut onto the diamond wheel, be sure to use only the special wheel spindle so that Makita Logo on Ezynut faces outside. guard designed for use with cut-off wheels. (In some European countries, when using a diamond wheel, the ordinary guard can be used.
- Page 14 For 100 mm (4″) model When installing the diamond wheel: When installing the abrasive cut-off wheel: 16 mm (5/8″) 16 mm (5/8″) ► 1. Lock nut 2. Diamond wheel (Thinner than 4 mm (5/32″)) 3. Diamond wheel (4 mm (5/32″) or thicker) ►...
-
Page 15: Operation
Grinding and sanding operation ► 1. Wire wheel brush Remove the battery cartridge from the tool and place it upside down allowing easy access to spindle. Turn the tool on and then apply the wheel or disc to the Remove any accessories on spindle. Thread wire wheel workpiece. -
Page 16: Maintenance
To maintain product SAFETY and RELIABILITY, repairs, any which causes over bending of wires when using other maintenance or adjustment should be performed by Makita the wire cup brush. It may lead to premature Authorized Service Centers, always using Makita replacement parts. - Page 17 Remove the dust cover from inhalation vent and clean it for smooth air circulation. ► 1. Dust cover NOTICE: Clean out the dust cover when it is clogged with dust or foreign matters. Continuing operation with a clogged dust cover may damage the tool.
-
Page 18: Optional Accessories
The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center. •... - Page 20 Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885767-225 www.makita.com 20191011...