Page 1
Electronic Modular Switching System Please read this manual before connecting the Electronic Modular Switching System. POWER MODEL KX-T206...
Page 2
Thank you for purchasing the Panasonic Model KX-T206, Electronic Modular Switching System. System Component Model No. Description Service KX-T206 Electronic Modular Switching System Unit Telephone KX-T7130 Proprietary telephone with display Proprietary telephone with display KX-T7030 KX-T7033 Proprietary telephone with display...
Page 3
Precaution • Keep the unit away from heating appliances and electrical noise generating devices such as fluorescent lamps, motors and television. These noise sources can interfere with the perfor- mance of the Electronic Modular Switching System. • This unit should be kept free of dust, moisture, high temperature (more than 40˚C/104˚F) and vibration, and should not be exposed to direct sunlight.
Table of Contents Specifications ........................5 Before Installation....................... 6 Unpacking ..........................7 Name and Location ......................7 Wall Mounting ........................8 Opening Front Cover......................8 Frame Ground Connection ....................8 System Connection Diagram ..................... 9 CO Line Connection ......................10 Extension Connection ......................
Specifications General Descriptions 1. Capacity ........CO line Extension 2. Control Method ......Stored Program CPU: 8 bits CPU Control ROM: 64 KB, Control RAM: 8 KB 3. Switching Method ..... Space Division CMOS Crosspoint Switch 4. Power Supplies ......Primary AC 110–240 V, 50/60 Hz Secondary Circuit Volt: +5V, +15 V, +30 V...
AC cord of the system and then on again. 8. The KX-T206 is equipped with a 3-wire grounding type plug. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the purpose of the grounding-type plug.
Unpacking • Main Unit ......one • Screw and Washer ....three • AC Cord ....... one • 4-pin Plug ......eight • AC Plug Adaptor ....one Name and Location Overview of the Main Unit AC Inlet POWE R Power Indicator Inside View of the Main Unit Cable Holders...
Wall Mounting 1. Place the templet (on page 33) on the wall to mark the three screw positions. Templet 2. Install the three screws and washers (included) into the wall. 3. Hook the main unit on the screw heads. Opening Front Cover 1.
CO Line Connection Wire Specification The wire specifications are as follows: Wire Solid wire Diameter of conductor 0.4 – 0.65mm (22, 24, 26 AWG Diameter with coating 0.66 – 1.05mm Connection Use a 4-pin plug (included) to connect CO lines. A single plug is able to connect two CO lines.
Extension Connection Wire Specification The wire specifications are as follows: Wire Solid wire Diameter of conductor 0.4 – 0.65mm (22, 24, 26 AWG Diameter with coating 0.66 – 1.05mm Connection Use a 4-pin plug (included) to connect extension lines. There are 6 plugs to connect extensions to EXTN. 1 through EXTN. 6 jacks.
Paralleled Telephone Connection Any single line telephone can be connected in parallel with a proprietary telephone. POWER Modular T-Adaptor 2-conductor wiring cord (Panasonic KX-J66 or USOC Connect pins “T” and “R”. RJA2X) 4-conductor wiring cord Connect pins “H”, “T”, “R”, and “L”.
2-conductor wiring cord KX-T30865 Notes • The doorphone adaptor is not required for KX-T206. • To avoid howling, you must assign all extensions as “DISABLE” in the “#06/#76 Doorphone Assignment (Day/Night)” program when you do not connect a doorphone. • If howling occurs while using the doorphone feature, check the wiring.
10 m (33 feet) above ground can be as high as 200,000 volts. This system should be installed with lightning protectors. In addition, grounding (connection to earth ground) is very important for the protection of the system. Recommended lightning protector • Panasonic KX-A207 Installation Lightning Main Unit Protectors...
Page 15
Installation of Lightning Protectors Outside (Main Building) Protectors (Another Building) Main EXTN Terminal Board Unit Lightning EXTN Protector EXTN EXTN Ground Notice If you install an extension outside of the main building, the following precautions are recom- mended: (1) Install the extension wire underground. (2) Use a conduit to protect the wire.
Page 16
Installation of Lightning Protectors Installation of the KX-A207 1. Secure the protector to a building with the enclosed mounting screws. 2. Remove about 1 cm ( inch) of insulation from the end of the earth wire. Insert the earth wire through the bottom of the protector base and secure it to the earth terminal.
Power Failure Transfer In the event of a power failure, CO2 is connected to extension 22 automatically. Note • The system programmed data is protected by the factory provided lithium battery. Starting the System Plug the AC power cord into the system and an AC outlet. •...
General Programming Instructions Default Setting This system has a default factory setting. If any of the program- ming needs to be changed, you can change the setting by system programming. Required Telephone Set You can use any of the following telephones for system program- ming: •...
System Programming System Speed Dialing Number Set Description Used to program System Speed Dial numbers. These numbers are available to all exten- sion users. There are 80 numbers from 00 through 79. Condition • A maximum of 32 digit numbers can be stored. •...
System Programming Outgoing Permitted CO2 Assignment (Day/Night) Description Determines the extensions which can have access to CO line 2 in both day and night modes. The extension users can make outgoing CO calls if their extensions are assigned as “ENABLE”. Input Format [A] [B] (for day)