Page 1
ORDER NO. VRD0107029C8 Video Cassette Recorder NV-FJ620AM / NV-FJ620AMC / NV-FJ620EU / NV-FJ620AU / NV-FJ620BD / NV-FJ620BDX / NV-FJ625AM / NV-FJ625AMM Z-MECHANISM SPECIFICATIONS 2001 Matsushita Electric Industrial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law.
Plate, distinguish the model number whether country of origin is mentioned on the Name Plate or not. [ * With Country of origin : NV-FJ620AMC ] [* Without Country of origin : NV-FJ620AM ] 2. For NV-FJ625AM/AMM : Since in both NV-FJ625AM and NV-FJ625AMM are indicated as “NV-FJ625AM” on the Name Plate, distinguish the model number whether country of origin is mentioned on the Name Plate or not.
Page 3
3. PG Shifter Adjustment Data 4. Option Setting Data When IC6001 and/or B6001 are replaced, all above listed data become not available. These data is backing up by using the power source of: *AC Connected : AC Power source *AC Disconnected : Back-up Battery (B6001) 2.1.1.
Page 4
theRemote Controller for cancellation.) [3. REPLACING PROCEDURE IN STEPS] [STEP 1. PREPARATION] 1. Remove the C.B.A. with Mechanism unit by referring the Disassembly procedure. 2. Connect the VFK1493P by referring the following figure. [STEP 2. “NAVI” DATA BACK-UP]...
Page 5
PROCEDURE F.I.P. DISPLAY Turn on the Service Mode. 1. Press FF and EJECT keys / simultaneously for more than / 3 seconds. Turn on the Service Mode 2. 2. Press FF and EJECT keys in twice. Turn on the Set-up mode. 3.
Page 6
necessary in previous model. [STEP 5. LINE-IN SETTING & ACTIVATE PLUG-IN A.T.P.] 1. Press the Channel up and down keys simultaneously for more than 3 seconds, under the condition of the no tape is in the unit. 2. Confirm that “A1” and “A2” can be displayed on the FIP by pressing the CH UP and CH DOWN buttons.
Page 7
PROCEDURE F.I.P. DISPLAY Turn on the Service Mode. 1. Press FF and EJECT keys / simultaneously for more than / 3 seconds. Turn on the Service Mode 2. 2. Press FF and EJECT keys in twice. Turn on the Back-up mode. 3.
Page 8
(See Fig.B1) Fig.B1 NOTE: The lithium battery is a critical component (Type No.:CR2354-1GUF Manufactured by Panasonic.) It must nerver be subjected to excessive heat or discharge. It must therefore only be fitted in equipment designed specifically for its use.
Page 9
2.4. SERVICE CAUTION-2 2.4.1. CAUTION FOR AUTO TUNING PROCEDURE Auto Tuning will start by the following procedure. 1. Connect the DIN-RF Cable. 2. Connect the AC Mains Lead. 3. Turn on the VCR. / Auto Tuning will start. / Auto Tuning searches for TV stations from VHF minimum to UHF maximum and memorizes every tuned program position.
Page 10
then turn the VCR off and on again to execute Auto tuning. 2. When Auto Tuning is canceled halfway, Auto Tuning is not executed even if the VCR is turned off and then turned on again. / In this case, Auto Tuning have to be restarted by the following procedure.
1. Removal of compulsory loading. A. Press FF and EJECT buttons simultaneously and set the Service Mode 7. B. Press STOP button in order to unload the mechanism. (Pay an attention of tape slack) Service Mode Indication: 7 ** ** (STOP) 7 00 ** (EJECT) 2.
Page 12
referring “Disassembly Procedure”. B. Remove the 3 screws (A) of the CYLINDER UNIT with a screw driver. C. Unlock the 4 locking tabs (B) and disconnect the Cylinder flexible card from the FPC Holder. D. Remove the CYLINDER UNIT. CAUTION Handle the Cylinder flexible card with care.
Page 13
3. UPPER CYLINDER ASSEMBLY When reassembling, perform the steps in the reverse order. Notes: A. Install the Cylinder Retainer so that the 2 holes on top of the Cylinder Retainer are at right angles with the P5001 Connection. B. Tighten the Hex screw (C) (1.5 mm) while pressing down on top of the Cylinder Retainer.
Page 14
C. Install the Cylinder Rotor Unit so that the inner hole of the Cylinder Rotor Unit fits to the small projection (D) on top of the Upper Cylinder. D. Tighten 2 screws (B). Fig. S9 E. Install the Cylinder Stator Unit. F.
Page 15
Refer to the Service Manual for Z Mechanism Chassis. (Order No.:VRD9802005C2) 2.6. INTRODUCTION OF VIDEO HEAD CLEANING CASSETTE (POLISHING TYPE) 1. We are pleased to introduce Panasonic Video Head Cleaning Cassette, VFK0923FT [for service purposes] and VFK0923FSE [for end users] for all VHS/SVHS VCP and VCR.
3. ADJUSTMENT PROCEDURES 3.1. DISASSEMBLY METHOD 3.1.1. DISASSEMBLY FLOW CHART This flow chart indicates disassembly steps of the cabinet parts and the circuit boards in order to find the necessary items for servicing. When reassembling, perform the steps in the reverse order. Fig.
4. REMOVAL OF THE MECHANISM UNIT Remove 3 Screws (E) Remove 2 Screws (F) Remove Screw (G) NOTE: Keep pressing 2 stoppers on the Cassette Holder Plate and press the Cassette Holder Plate to the rear. / [CAUTION -Mounting the Mechanism unit to Main C.B.A.] A.
5. REMOVAL OF THE MAIN C.B.A. Disconnect 4 Screws (H) Unlock 4 Tabs ( I ) Fig. D6 6. REMOVAL OF THE BOTTOM PLATE Unlock 12 Tabs (J) Fig. D7 7. SERVICE POSITION...
Page 21
Fig. D8 3.2. MECHANICAL ADJUSTMENT PROCEDURES Refer to the Service Manual for Z-Mechanism Chassis. / (Order No. VRD9802005C2) 3.3. ELECTRICAL ADJUSTMENT PROCEDURES This section provides complete adjustment procedures required for electric circuits of VCR. 3.3.1. TEST EQUIPMENT To perform electrical adjustments following equipment is required. 1.
Page 22
PROCEDURES DISPLAY 5. Insert the Alignment Tape. (VFJ8125H3F) 6. This adjustment is automatically started after VCR goes PLAY mode. / (During the adjustment, the picture will be appeared on the monitor.) 7. When this Adjustment is terminated, the following operation will be activated. Adjustment completed: The tape will be ejected.
7.1. SYSTEM CONTROL& SERVO/ TIMER SECTION BLOCK DIAGRAM 7.2. VIDEO SECTION BLOCK DIAGRAM 7.3. FM AUDIO SECTION BLOCK DIAGRAM 8. SCHEMATIC DIAGRAMS 8.1. POWER SECTION IN MAIN SCHEMATIC DIAGRAM 8.2. SYSTEM CONTROL& SERVO/ TIMER SECTION IN MAIN SCHEMATIC DIAGRAM 8.3. VIDEO SECTION IN MAIN SCHEMATIC DIAGRAM 8.4.
11.1. MECHANICAL REPLACEMENT PARTS LIST 11.1.1. CHASSIS PARTS LIST...
Page 33
Ref. No. Part No. Part Name & Description Remarks VEG1522 CYLINDER UNIT NV-FJ620AM/ / AMC/BD/BDX, / FJ625AM/AMM VEG1565 CYLINDER UNIT [SUPPLIED / FROM MAV] / NV -FJ620AU/ / EU VXP2001 UPPER CYLINDER UNIT NV-FJ620AM/ / AMC/BD/BDX, / FJ625AM/AMM VXP2086 UPPER CYLINDER UNIT...
Page 34
Ref. No. Part No. Part Name & Description Remarks VXL2792 IDLER ARM UNIT VXL2733 SUPPLY BRAKE ARM UNIT VXL2747 LOADING RACK UNIT VXP2035 CENTRE CLUTCH UNIT VMA9516 TOP PLATE VMB3047 CONNECTION SPRING VMD3379 SIDE PLATE (L) VXA6540 SIDE PLATE (R) UNIT VXA5746 CASSETTE HOLDER UNIT VXP1730...
Page 35
[SUPPLIED / FROM MAV] / NV -FJ625AM/ / AMM VKF3347 BLINDER PANEL [SUPPLIED / FROM MAV] VMB2521 BLINDER SPRING VJA1038 AC CORD / NV-FJ620AM/ / AMC/AU/ EU/ / BDX,FJ625AM/ / AMM VJA1138 AC CORD / [SUPPLIED / FROM MAV] / NV-FJ620BD VKA0192 VJH1142 ANT BOARD...
Page 36
Part No. Part Name & Description Remarks VQT9302 OPERATING INSTRUCTIONS / (ENGLISH / ARABIC) / [SUPPLIED / FROM MAV] / NV-FJ620AM/ / AMC VQT9303 OPERATING INSTRUCTIONS / (ENGLISH) / [SUPPLIED / FROM MAV] / NV-FJ620AU/ / EU VQT9304 OPERATING INSTRUCTIONS / (RUSSIAN)
Ref. No. Part No. Part Name & Description Remarks VEP06E21M MAIN C.B.A. [SUPPLIED / FROM MAV] / (RTL) / NV-FJ620AM/ / AMC VEP06E21N MAIN C.B.A. [SUPPLIED / FROM MAV] / (RTL) / NV-FJ620EU VEP06E21P MAIN C.B.A. [SUPPLIED / FROM MAV] /...
Page 38
Ref. No. Part No. Part Name & Description Remarks VEP06E21M MAIN C.B.A. [SUPPLIED / FROM MAV] / (RTL) / NV-FJ620AM/ / AMC VEP06E21N MAIN C.B.A. [SUPPLIED / FROM MAV] / (RTL) / NV-FJ620EU VEP06E21P MAIN C.B.A. [SUPPLIED / FROM MAV] /...
Page 56
Ref. No. Part No. Part Name & Description Remarks ------------ CYLINDER STATOR C.B.A. MISCELLANEOUS VJS3537B009G CONNECTOR (FEMALE) 9P K1MN09B00023 HW-300A-DF HALL IC B4AAB0000007 12. Schematic Diagram For Printing With A4 Size...