hit counter code
Samsung BIXOLON SPR-270 User Manual
  1. Manuals
  2. Brands
  3. Samsung Manuals
  4. Recording Equipment
  5. BIXOLON SPR-270
  6. User manual

Samsung BIXOLON SPR-270 User Manual

Ethernet interface
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
All manuals and user guides at all-guides.com
User's Manual
Ethernet Interface
Rev. 4.00
http://www.samsungminiprinters.com
SRP-270
SRP-275
SRP-350
SRP-350plus
SRP-370 / 372
SRP-770 / 770II
SLP-T400

Advertisement

Table of Contents
loading

Related Manuals for Samsung BIXOLON SPR-270

Summary of Contents for Samsung BIXOLON SPR-270

  • Page 1 All manuals and user guides at all-guides.com User's Manual Ethernet Interface Rev. 4.00 SRP-270 SRP-275 SRP-350 SRP-350plus SRP-370 / 372 SRP-770 / 770II SLP-T400 http://www.samsungminiprinters.com...

  • Page 2: Table Of Contents

    All manuals and user guides at all-guides.com Ethernet ■ Table of contents 1. Manual Information......................3 2. Interface card and available printer................3 3. Specifications.........................4 3-1. Hardware version....................4 3-2. Configuration Tool....................4 3-3. Virtual Driver ......................5 3-4. Hardware version and Configuration Tool............5 3-5. Details of interface card ..................5 4.

  • Page 3: Manual Information

    All manuals and user guides at all-guides.com Ethernet 1. Manual Information The purpose of this manual is to provide information on the operation and usage instructions of the Ethernet Interface for the BIXOLON Printers. 2. Interface card and available printer Printer Interface Card Hardware version...

  • Page 4: Specifications

    All manuals and user guides at all-guides.com Ethernet 3. Specifications 3-1. Hardware version Hardware version is marked on the label on the interface card bracket. Interface Ver: V4.X.X has Function key while Ver:V3.X.X doesn’t have it. IFA-E TYPE IFC-E TYPE [Note] - The DIP switch on the interface board should always be OFF.

  • Page 5: Virtual Driver

    All manuals and user guides at all-guides.com Ethernet 3-3. Virtual Driver - It converts output of Serial (COM) port into output of Ethernet (TCP/IP) port. - It is available for Windows 2000, XP and 2003 server. 3-4. Hardware version and Configuration Tool Hardware Configuration Tool Network...

  • Page 6: How To Install

    All manuals and user guides at all-guides.com Ethernet 4. How to install 1) Check the interface version [Note] - Each version uses its own Configuration Tool. 2) Turn of the printer and insert the interface card. 3) Set the baud rate (Serial speed) - SRP-270,275: Max.

  • Page 7: Static Ip Interface Set Up

    All manuals and user guides at all-guides.com Ethernet 5. Static IP interface set up 5-1. Configuration Tool 1) Turn on the printer. 2) Execute Configure Tool. [Note] - Use proper Configuration Tool dependent on hardware version 3) Click Search. - 7 - V 4.00...
  • Page 8 All manuals and user guides at all-guides.com Ethernet 4) Select MAC Address in Board list and set up Network Setting. MAC Address [Note] - If many MAC addresses appear, refer to the MAC address on the label of the interface card. - Ask the Network administrator IP and its related information.
  • Page 9 All manuals and user guides at all-guides.com Ethernet 5) Enter value at Local Port. [Note] - Default value is 9100. Choose from 6000 to 10000. 6) Set Inactivity Time as ‘0’. [Note] - Default value is 0. Choose from 0 to 65535. - When you set Inactivity time, Ethernet interface will disconnect by force after designated time.
  • Page 10 All manuals and user guides at all-guides.com Ethernet 7) Set baud rate (Speed) at Serial Setting [Note] - The baud rate (Speed) should be same as the baud rate of the printer. (Refer to [Appendix 1]) - Highest baud rate (Speed) can be used. 8) When setting finishes, click Setting.
  • Page 11 All manuals and user guides at all-guides.com Ethernet 9) Click Exit to finish set up. - 11 - V 4.00...

  • Page 12: Web Server

    All manuals and user guides at all-guides.com Ethernet 5-2. Web Server 1) Execute Internet Explorer. 2) Enter IP address of the printer at Address of Internet Explorer and click go. [Note] - If you are not aware of IP address, check IP address by pushing Function key. (Refer to [Appendisx2]) - Ask Network administrator IP Address and its related information.
  • Page 13 All manuals and user guides at all-guides.com Ethernet [Note] - If you are not aware of Subnet Mask, refer to the below. - When the IP address is (1) 1~126.xxx.xxx.xxx: Subnet Mask: 255.0.0.0 (2) 128~191.xxx.xxx.xxx: Subnet Mask: 255.255.0.0 (3) 192~223.xxx.xxx.xxx: Subnet Mask: 255.255.255.0 For example, when the IP address is 192.168.192.321, Subnet mask is 255.255.255.0.
  • Page 14 All manuals and user guides at all-guides.com Ethernet 6) Set baud rate (Serial speed). [Note] The baud rate (Speed) should be same as the baud rate of the printer. (Refer to [Appendix 1]) 7) When setting finishes, click Apply. [Note] When the setting finishes successfully, the following message appears.
  • Page 15 All manuals and user guides at all-guides.com Ethernet 8) If you click the message, you can check your configuration setting. [Note] - If any change was not found after setting on Web Server, check the bellows; (1) Execute Internet Explorer. (2) Internet Explorer Menu →...
  • Page 16 All manuals and user guides at all-guides.com Ethernet (4) Check for newer version of stored pages → Click Every visit to the page. (5) Click Refresh in Internet Explorer. - 16 - V 4.00...

  • Page 17: Dhcp Interface Set Up

    All manuals and user guides at all-guides.com Ethernet 6. DHCP interface set up 6-1. Configuration Tool 1) Turn on the printer. 2) Execute Configure Tool. [Note] - Use proper Configuration Tool dependent on hardware version 3) Click Search. - 17 - V 4.00...
  • Page 18 All manuals and user guides at all-guides.com Ethernet 4) Select MAC Address in Board list and check at DHCP Mode. MAC address [Note] - If many MAC addresses appear, refer to the MAC address on the label of the interface card. - Ask the Network administrator IP and its related information.
  • Page 19 All manuals and user guides at all-guides.com Ethernet 6) When setting finishes, click Setting. [Note] Successfully finished set up Unsuccessfully finished set up - When setting doesn’t finish correctly, try again. 7) Wait approximately 10 or more seconds until the printer receives IP from the server. - 19 - V 4.00...
  • Page 20 All manuals and user guides at all-guides.com Ethernet 8) Click Search to check given IP. 9) If the given IP is OK, click Exit. - 20 - V 4.00...

  • Page 21: Web Server

    All manuals and user guides at all-guides.com Ethernet 6-2. Web Server 1) Check at DHCP mode and click Apply. 2) Push the Function Key on the interface 10 or more seconds from finishing set up. Enter given IP address at address of Internet Explorer to enter web server. - 21 - V 4.00...

  • Page 22: Firmware Update

    All manuals and user guides at all-guides.com Ethernet 7. Firmware update 7-1. Configuration Tool 1) Turn on the printer 2) Execute Configure Tool. [Note] - Use proper Configuration Tool dependent on hardware version 3) Click Search. - 22 - V 4.00...
  • Page 23 All manuals and user guides at all-guides.com Ethernet 4) Select MAC Address in Board. MAC Address [Note] - If many MAC addresses appear, refer to the MAC address on the label of the interface card. 5) Click Upload and select file to download. - 23 - V 4.00...
  • Page 24 All manuals and user guides at all-guides.com Ethernet [Note] - Check the extension of the file, which should be “bin”. Successfully finished F/W update Unsuccessfully finished F/W update - Printer and available firmware Printer Firmware SRP-770, SRP-770II, SLP-T400 ethernettoserial_v5.X Except SRP-770, SRP-770II ethernettoserial_v2.X 6) When firmware update finishes, click Search to check if Firmware is updated successfully.

  • Page 25: Web Server

    All manuals and user guides at all-guides.com Ethernet 7-2. Web Server 1) Click Firmware update. 2) Internet Explorer is executed and it moves to download site automatically. [Note] Printer and available firmware Printer Firmware SRP-770, SRP-770II, SLP-T400 ethernettoserial_v5.X Except SRP-770, SRP-770II ethernettoserial_v2.X - 25 - V 4.00...
  • Page 26 All manuals and user guides at all-guides.com Ethernet 3) Download Configure_Vx.xx.zip file and *.bin file. [Note] You can download it by double-clicking icons or copy and paste. 4) Unzip Configure_Vx.xx.zip and execute Configure_Vx.xx.exe at Configure_Vx.xx folder. [Note] - In case Configure_Vx.xx.exe can’t be executed, run configure_setup.bat first and retry it.

  • Page 27: Ethernet Test By Using Windows Test Page

    All manuals and user guides at all-guides.com Ethernet 8. Ethernet test by using Windows test page If you don’t have any test program to check printer’s performance, you can use Windows driver. It is available for Windows 2000, XP and 2003 server. 1) Install Windows driver of the printer.
  • Page 28 All manuals and user guides at all-guides.com Ethernet 4) Select Ports tab. 5) Click Add Port. - 28 - V 4.00...
  • Page 29 All manuals and user guides at all-guides.com Ethernet 6) Select Standard TCP/IP Port and click New port. 7) When standard TCP/IP printer add wizard window pops up, click Next. 8) Enter printer IP at Printer Name or IP Address and click Next. [Note] Enter same IP address as the Ethernet interface card.
  • Page 30 All manuals and user guides at all-guides.com Ethernet 9) Click Next. [Note] Click Next without any selection nor change. 10) Click Finish. 11) Click Close to close Printer port window - 30 - V 4.00...
  • Page 31 All manuals and user guides at all-guides.com Ethernet 12) Click Configure Port. 13) Enter same port number as the value of Local Port of the Ethernet interface at Raw Setting. [Note] There is no change except Raw Setting. - 31 - V 4.00...
  • Page 32 All manuals and user guides at all-guides.com Ethernet 14) Click OK. 15) Select General tab and click Print Test Page to check if the printer works properly. - 32 - V 4.00...

  • Page 33: [Appendix 1] Printer Dip Switch Set Up

    All manuals and user guides at all-guides.com Ethernet [Appendix 1] Printer DIP switch set up Printer Baud rate & DSW set up Handshaking & Parity Baud rate DSW 1-7 DSW 1-8 57600bps DTR/DSR : SW 1-3 OFF SRP-350 8 data bit : SW 1-4 OFF 38400bps None parity : SW 1-5 OFF 19200bps...

  • Page 34: [Appendix 2] Function Key Set Up

    All manuals and user guides at all-guides.com Ethernet [Appendix 2] Function Key set up 1. How to use (1) Turn on the printer (2) Wait 10 or more seconds until the Ethernet interface boots up (3) Push the Function key Function key SRP-770II (4) The settings will be printed only one time since the printer is turned on.

  • Page 35: [Appendix 3] Factory Reset

    All manuals and user guides at all-guides.com [Appendix 3] Factory Reset Default setting after factory reset - Activate DHCP mode - Local Port: 9100 - Inactivity Time: 0 - Speed SRP-770II, SLP-T400: 230400 bps SRP-270, SRP-275, SRP-350, SRP-350plus, SRP-370, SRP-372: 9600 bps 2.

This manual is also suitable for:

Bixolon spr-275Bixolon spr-350Bixolon spr-350plusBixolon spr-370Bixolon spr-372Bixolon spr-770 ... Show all

Table of Contents