Samsung SWA-9100S - Acoustic Amplifier Manual

CHECKING THE COMPONENTS

Wireless Receiver Module / Surround Speaker X 2 / Speaker Cable X 2 / Power Cord

NOTES

• For more information about the power supply and power consumption, refer to the label attached to the product.
  (Label: Rear of the Main Unit)
• Design and specifications are subject to change without prior notice.

CONNECTING TO A SOUNDBAR

1. Connect the Wireless Receiver Module to 2 Surround Speakers

Use the speaker cables to connect the two surround sound speakers to the Wireless Receiver Module.

• When connecting the speaker cable, connect the core wire to the speaker.
  
• The speaker cables are colour coded.
  
• When connecting the speaker cables to the Wireless Receiver Module, follow these steps:

1. Insert the grey plug into the grey jack on the Wireless Receiver.
2. Insert the blue plug into the blue jack on the Wireless Receiver.

• When connecting the speaker cables to the surround speakers, follow these steps:

1. Match the speaker cable connected to the grey jack to the speaker with the grey label.
2. Match the speaker cable connected to the blue jack to the speaker with the blue label.
3. Insert the red and black coloured ends of each speaker cable into the red and black jacks of the appropriate speaker.

• The labels are on the backs of the speakers.

2. Check the standby status after plugging into an electrical outlet
   Plug the Wireless Receiver Module power cord into an electrical outlet and into the Wireless Receiver Module to turn on the Wireless Receiver Module. The LINK LED indicator (blue LED) on the Wireless Receiver Module blinks. If the LED does not blink, refer to step 6.
   
3. Turn off the Soundbar
   Turn off the Soundbar using the Soundbar's remote control or by (Power) button on the main Soundbar unit.
   

• The image of the Soundbar may differ from your Soundbar, depending on the model.

4. Configure "ID SET" using the Soundbar's remote control
   Press the Up button on the Soundbar remote control for 5 seconds.

• The ID SET message appears on the Soundbar main unit's display for a short time and then disappears.
• After the ID SET process, the Soundbar power is automatically turned on.
  
• The image of the Soundbar may differ from your Soundbar, depending on the model.

5. Check if the LINK LED is solid blue (connection complete)
   The LINK LED indicator stops blinking and glows a solid blue when a connection is established between the Soundbar and the Wireless Receiver Module.
   
6. If the SWA-9100S does not connect, take the necessary steps according to the LED Indicator's status

LINK (Blue) On : Connected with the Soundbar.

LINK (Blue) Blinking : Connection standby status.

• Check if the Soundbar is turned on.
• Repeat steps 3 through 5.

STANDBY (Red) On : Connection failure.

• Check if the Soundbar is turned on.

1. Press the ID SET button on the back of the Wireless Receiver Module with a pen tip for 5~6 seconds until the LINK LED indicator blinks (in Blue).
   
2. Repeat steps 3 through 5.

Others : Errors

• Contact a Samsung Service Centre.

COMPATIBLE MODELS

• Compatible with select Samsung Soundbar. Please visit the Soundbar product page at www.samsung.com/support for more information.
• Compatible model list is subject to change without further notice.

OPEN SOURCE LICENCE NOTICE

To send inquiries and requests for questions regarding open sources, contact Samsung Open Source
(http://opensource.samsung.com)

SPECIFICATIONS AND GUIDE

Specifications

NOTES

• Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
• Weight and dimensions are approximate.
• For India Only
  "This product is RoHS compliant"

Documents / Resources

References

• Support Home | Official Samsung Support US
• Samsung Open Source

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Samsung SWA-9100S - Acoustic Amplifier Manual