Fujitsu PRIMERGY TX200FT S2 Start Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

��

■PRIMERGY TX200FT S2 Manuals

Manuals for this server can be accessed from the section below of the PRIMERGY Document & Tool CD.

[CD-ROM Drive] :\MANUAL\INDEX.PDF

Manuals can be displayed using Acrobat

Checking the items

supplied

Using the "Contents List", check that no supplied

or attached items are missing. If any items are

missing, contact an office listed in the "Contact

Information.

Installing internal options

If internal options have been purchased separately, install them before installing the Operating System.

nPoints to note when installing

internal options

When installing internal options, perform operations after

reading the following manuals.

��

"Chapter 5 Installing Internal Options"

"PRIMERGY ServerBooks"/

��

"Supplement"

When installing memory or hard disk, always install the

same capacity of memory or hard disk to both enclo-

sures.

TX200FT S2

Reader

or Adobe

Reader

. If using Acrobat

Reader

, use version 4.0 or later.

Checking "Safety Pre-

cautions"

Before using this server, be sure to check the at-

tached "Safety Precautions" guidelines.

Also check the guidelines when connecting, installing

internal options and setting up this server.

n Available internal options and

installation locations

��

After installing internal options, check that the order and

location of installation are correct and cables are cor-

rectly attached.

B7FH-3821-01EN-00

��

Table of Contents

Summary of Contents for Fujitsu PRIMERGY TX200FT S2

Page 1: Installing Internal Options
TX200FT S2 �� ■PRIMERGY TX200FT S2 Manuals Manuals for this server can be accessed from the section below of the PRIMERGY Document & Tool CD. [CD-ROM Drive] :\MANUAL\INDEX.PDF Manuals can be displayed using Acrobat ® Reader ®...
Page 2: Installing The Server To The Rack
Checking location before installing the server nConditions �� ■Installing the server to the rack Make sure to contact an office listed in the "Contact Information" before attempting to install or remove the serv- er from the rack.
Page 3 Attach M5 rack nuts. Insert the server to install it to the rack. Use 4U for each enclosure. Insert the inner rail attached to the server to the Insert the rack nuts in the 2nd and 11th hole posi- grooves of the slide rail and slide the server to- tions, counting up from the base of the server, from wards the back.
Page 4: Connecting Peripheral Devices
Connecting peripheral devices Peripheral devices, such as the keyboard and mouse, etc., are connected to the server in the following order. lConnecting the LAN cables lConnecting the display, keyboard and mouse �� ...
Page 5: User Information
nFilling in the pair identification label Fill in the label on the front of the server so that it is clear that FT1 and FT2 are a pair. Also, inform the support desk of the product ID and number of the FT1/FT2 when you contact them. Be sure to fill in this information.
Page 6: Network Configuration
n Validation interval at automatic shutdown This setting required for the use of UPS. For details about various settings, refer to "3.4 UPS Settings" in the "User's Guide". The numbers in brackets ( ) are setting examples. Item Actual Setting Parameters Time "Power Failure"...
Page 7 Turning on the power and run mini-setup of each OS This section explains how to run mini-setup of CoServer1, CoServer2 and FTvirtual Server. To run mini-setup of FTvirtual Server, CoServer1 and 2 must already be run mini-setup. Run mini-setup in the following order. (1) Turn on the FT1 power and run mini-setup of CoServer1.
Page 8 Click [Yes]. When the server restarts, press the power switch on the front of the server CoServer restarts. straight away and turn off the power After restarting, the POST screen (or supply. "PRIMERGY" logo) appears. nRunning mini-setup of the CoServer2 The running mini-setup procedure is the same as for CoServer1.
Page 9: Turning The Server Off
Right-click on the FTvirtual Server icon Click [OK] to close the [Component Prop- erties] window and Endurance Manager and select "Properties". will end. The [Component Properties] window appears. Set IP addresses for the following adapt- ers. Because DHCP is preset to automatically acquire IP addresses, if these IP addresses are acceptable the following procedures are not required.
Page 10: Pre-Operation Settings
After running mini-setup of the OS, refer to the The latest PRIMERGY, driver, and software information is following and perform FT-system settings. available at the address below. Use as necessary. http://primergy.fujitsu.com �� "Chapter 3 Pre-operation Settings" lBefore requesting repairs When using UPS, perform UPS settings.
Page 11: Contact Information
Tel: +1-800-831-3183 Tel: +60-3-8318-3700 Fax: +1-408-496-0575 Fax: +60-3-8318-8700 Address: 1250 East Arques Avenue, Sunnyvale, CA USA 94088-3470 Address: 1st Floor, No.3505 Jalan Technokrat 5 63000 Cyberjaya, Selangor Darul Ehsan Malaysia For the latest information, refer to the Fujitsu PRIMERGY website (http://primergy.fujitsu.com).
Page 12 It is the customer's responsibility to maintain backup copies in advance. In case of data loss, Fujitsu assumes no liability for data maintenance or restoration and damages that occur as a result of the data loss for any reason, except for items covered under warranty.

Fujitsu PRIMERGY TX200FT S2 Start Manual

Quick Links

Installing internal options

internal options

Related Manuals for Fujitsu PRIMERGY TX200FT S2

Summary of Contents for Fujitsu PRIMERGY TX200FT S2

Table of Contents