WASHING MACHINE SWV-1200F/1100F/1000F/800F P1291/P1091/P8091/P6091 SERVICE Manual WASHING MACHINE CONTENTS 1. SPECIFICATIONS 2. OVERVIEW OF THE WASHING MACHINE 3. OVERVIEW OF THE CONTROL PANEL 4. PROCESS TABLE 5. GENERAL REEOR FUNCTION 6. TROUBLE DIAGNOSIS 7. TEST MODE 8. DESIGNATION OF MAIN COMPONENTS 9.
19. When the wash-heater is replaced, check it is inserted in the bracket-heater and screw the nut. If the wash-heater is not inserted in the bracket-heater properly, this may cause the noise and leakage since it is contacted to the drum. SAMSUNG ELECTRONICS CO., LTD...
240 V 180 W WASHING and 220 V 2000 W HEATING 240 V 2400 W MODEL P6091 SWV-800F/P8091 SWV-1000F/P1091 SWV-1100F SWV-1200F/P1291 SPIN 220 V 380 W 430 W 500 W 550 W 550 W 240 V 380 W 430 W...
2. Overview of the Washing Machine WATER SUPPLY VALVE CONTROL-PANEL DRAWER ASSY DOOR SENSOR PRESSURE ADJUSTABLE LEG ASSY PUMP HOSE DRAIN(OPTION) CAP DRAIN(OPTION) POWER CORD BUFFER SPRING WEIGHT-BALANCE DRAIN HOSE PULLEY BELT SHOCK ABSORBER ASSY MOTOR SAMSUNG ELECTRONICS CO., LTD...
(cold water, 30°C, 40°C, 60°C and 95°C). 4. Spin selection button Press the button repeatedly to cycle through the available spin speed options SWV-1200F/P1291 : (No spin, Rinse hold, 400, 600, 800, 1000and 1200rpms), SWV-1100F : (No spin, Rinse hold, 400, 600, 800, 1000and 1100rpms), SWV-1000F/P1091 : (No spin, Rinse hold, 400, 600, 800, and 1000rpms), 5.
Page 6
10minutes without any buttons being touched, the power automatically turns off. 11. No Spin button(OPTION) Press to no spin program. 12. Rinse Hold button(OPTION) Press to rinse hold program. SAMSUNG ELECTRONICS CO., LTD...
- At the time of initial water supply, if the water temperature is not appropriate, water starts to be drained and it is forced to be drained for 2 min when the abnormal frequency of 25.24KHz is detected. - Display shows ‘E8’. - This error can be cleared by POWER S/W OFF. SAMSUNG ELECTRONICS CO., LTD...
Page 8
5) Part the diaphragm and the wire diaphragm away from the frame-front. 6) Remove the eight screws fixing the frame-front. 7) It’s possible to exchange and service the heater, the pump, the shock-absorber and the door lock s/w. LEVER SAMSUNG ELECTRONICS CO., LTD...
Page 9
4) Remove the motor. Motor Assemble Hole 5. How to Assemble the RELAY Housing. Relay <CAUTION> Insert the Relay Housing to the Relays on the opposite direation each other. RELAY Housing Heat Sink SAMSUNG ELECTRONICS CO., LTD...
17mm. Vice pliers Tool to protect the idle and abrasion of the bolt for the box driver. Other(Driver, Nipper, Long nose) General tools for the after service. JIG for the Tub 1 (Disassemble and Assemble) SAMSUNG ELECTRONICS CO., LTD...
5) As the parts on P.C.B are coated by the urethane, they can not be tested by the test bar of the meter. Check the trouble by the test mode method according to the procedure. SAMSUNG ELECTRONICS CO., LTD...
Page 12
The heating is not executed. - Is the wash heater terminal unplugged? Ω - Is the wash heater normal?(Resistance value : 20.5~21.5 - If above points are not found, the PCB assembly is out of order. Replace it. SAMSUNG ELECTRONICS CO., LTD...
Pre-wash VALVE ON(0.3sec) OFF(0.3sec) Main wash(0.3sec) OFF(0.3sec) Rinse VALVE ON(0.3sec) OFF(0.3sec) Pump MOTOR ON(0.3sec) OFF(0.3sec) MOTOR RELAY1 ON(0.3sec) OFF(0.3sec) MOTOR RELAY2(0.3sec) OFF(0.3sec) MOTOR RELAY2 ON(0.3sec) OFF(0.3sec) HEATER RELAY ON(0.3sec) OFF(0.3sec) DOOR OPEN (Function continues when door is closed) SAMSUNG ELECTRONICS CO., LTD...
1) Capacity : AC 230V/2000W 2) Location : Bottom of TUB 3) Function : Raise the water temperature Thermistor supplied at the wash process. 4) Resistance value : 23Ω ~ 29Ω 5) Thermo Fuse : 128°C SAMSUNG ELECTRONICS CO., LTD...