Camera Drive Unit Operating Instructions WV-PS154 Model No. 1 5 4 it W V- PS POW ER Ca m er a Dr ive Un FLAS H POW ER LED WILL MAL TIFU NCT ION IF COO LING FAN Before attempting to connect or operate this product,...
Page 2
If you lose the fuse cover the plug must not be used until a replacement cover is obtained. DO NOT REMOVE COVER (OR BACK). A replacement fuse cover can be purchased from your local Panasonic Dealer. NO USER-SERVICEABLE PARTS INSIDE.
ENGLISH VERSION CONTENTS PREFACE ...................................... 4 FEATURES ....................................4 PRECAUTIONS ..................................... 4 MAJOR OPERATING COMPONENTS AND THEIR FUNCTIONS ....................5 Front View ....................................5 Rear View ....................................5 INSTALLATION ..................................... 6 Mounting in the rack ................................6 SYSTEM CONNECTION ................................7 SPECIFICATIONS ..................................
PREFACE The Panasonic WV-PS154 Camera Drive Unit drives up to four VP (Video and Power) multiplex cameras. This simple system is designed to meet the surveillance and security needs of offices, factories, public and resi- dential buildings, etc. FEATURES • Up to four VP multiplex cameras of the specified model •...
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS Front View Power SWITCH PROTECTOR POWER LED WILL FLASH Camera Drive Unit WV-PS IF COOLING FAN MALFUNCTIONS Rear View VD/SYNC SIGNAL VD/SYNC (4V[p-p]75 ) CAMERA IN VIDEO OUT AUDIO OUT q Power On/Off Switch (POWER ON/OFF) t VD/SYNC Input Connector (VD/SYNC IN) The VD (Vertical Drive) pulse or VS (Video Sync) signal This switch is used to turn the camera drive unit and...
INSTALLATION The installations described below should be made by 3. Install the camera drive unit with the rack mounting qualified service personnel or system installers. brackets on the rack using four screws (not supplied). Mounting in the Rack 1. Remove the four rubber feet by removing the four screws on the bottom of the camera drive unit.
• Be sure to connect the cameras and camera input1 the wrong connection will operate and prevent the correctly. The synchronizing signal will not be sup- cameras from functioning. plied if their connection is faulty. <Extended System > Camera Drive Unit WV-PS154 VD/SYNC SIGNAL VD/SYNC (4V[p-p]75 ) CAMERA IN...
Page 8
2 ch 3 ch 4 ch VD/SYNC SIGNAL VD/SYNC CAMERA IN VIDEO OUT AUDIO OUT (4V[p-p]75 ) Camera Drive Unit WV-PS154 A L A R M / R E M OT E SIGNAL GND CAMERA SPOT VS/VD RS485 DATA MODE Monitor...
Page 9
DATA 5 PRINTER DATA 6 POWER DATA 7 125V 4V DATA 8 VS/VD DATA 1 DATA 2 11A00001 VIDEO OUT2 Camera Drive Unit WV-PS154 VD/SYNC SIGNAL VD/SYNC CAMERA IN VIDEO OUT AUDIO OUT (4V[p-p]75 ) Cameras System Controller DATA WV-CU550A...
Page 10
1. Connect a coaxial cable from a camera to a CAMERA External VD/SYNC Signal IN connector of the camera drive unit. Maximum cable lengths are approximately as shown below. Signal Level The VD/SYNC IN connector receives the VD or VS synchro- Coaxial DC R/300 m (1000 ft.) of Maximum...
SPECIFICATIONS Power Source: 220-240 V AC 50 Hz Power Consumption: Approx. 55 W Camera Input: 1.0 V[p-p]/75 , BNC Connector Video Output: 1.0 V[p-p]/75 , BNC Connector Audio Output: –10 dB/600 unbalanced, RCA pin jack Camera Power Supply: Regulated current multiplex method (350 mA) Maximum Distance to Camera: Coaxial DC R/300 m (1000 ft.) of...