TK-7160 GENERAL 3. PRE-INSTALLATION CHECKOUT INTRODUCTION 3-1. Introduction SCOPE OF THIS MANUAL Each radio is adjusted and tested before shipment. How- This manual is intended for use by experienced techni- ever, it is recommended that receiver and transmitter opera- cians familiar with similar types of commercial grade commu- tion be checked for proper operation before installation.
Your sand from getting in. KENWOOD dealer can help you select an antenna system that will best serve your particular needs. 5-2. Radio location Select a convenient location for your control station radio which is as close as practical to the antenna cable entry point.
TK-7160 OPERATING FEATURES 1. Controls and Functions Press to activate its programmable function. The default 1-1. Front Panel setting is None (no function). !5 PTT switch Press this switch, then speak into the microphone to call a station. 1-3. Display 1-2.
The data can be input to or read from TK-7160 and edited on the screen. The programmed or edited data can be printed out. It is also possible to tune the transceiver.
TK-7160 REALIGNMENT 4-1. Adding the data password. 5. Self Programming Mode If the data password is set in the optional feature menu, Write mode for frequency data and signaling, etc. To be you must enter the password (Master transceiver) to activate used ONLY by the authorized service person maintaining the a clone mode.
Page 7
TK-7160 REALIGNMENT ■ Item Selection Mode ■ Item Setting Mode Display [ ] + Power on Display Current → Self programming mode SE L F 1. RX frequency 1 3 6 0 0 0 0 0 setting value Value is not set –...
Page 8
TK-7160 REALIGNMENT 3. Insert the KCT-39 cable ( ) into the chassis ( ). The 6. Accessory Connection Cable (KCT-39) wire harness band ( ) must be inside the chassis and The KCT-39 is an accessory connection cable for connect- face down.
Page 9
TK-7160 REALIGNMENT / INSTALLATION 7. Ignition Sense Cable (KCT-18) 1. PA/HA Unit (KAP-2 : Option) The KCT-18 is an optional cable for enabling the ignition 1-1. Installing the KAP-2 in the Transceiver function. The ignition function lets you turn the power to the The Horn Alert and Public Address functions are enabled transceiver on and off with the car ignition key.
TK-7160 INSTALLATION 5. Affix the 20 x 20 x 2.5 mm pad to the 40 x 33 mm transpar- 8. Attach the supplied cable to the CN3 connector of the ent sheet, then attach it to the TX-RX unit printed area as KAP-2 unit and the CN6 connector of the TX-RX unit.
TK-7160 INSTALLATION / DISASSEMBLY FOR REPAIR 1. When you remove the panel, turn the transceiver up side 2. External Speaker (Option) down. Detach the panel by lifting the tabs as shown be- 2-1. KES-3 low. The KES-3 is an external speaker for the 3.5-mm-diameter Tabs speaker jack.
TK-7160 CIRCUIT DESCRIPTION ■ IF Amplifier Frequency Configuration The first IF signal is amplified by Q351, and the enters The receiver utilizes double conversion. The first IF is IC321 (FM processing IC). The signal is heterodyned again 49.95MHz and the second IF is 450kHz. The first local oscil- with a second local oscillator signal within IC321 to create a lator signal is supplied from the PLL circuit.
Page 13
TK-7160 CIRCUIT DESCRIPTION ■ Wide/Narrow Switching Circuit ■ Squelch Circuit The Wide port (pin 23) and Narrow port (pin 22) of the CPU The detection output from the FM IF IC (IC321) passes is used to switch between ceramic filters. When the Wide through a noise amplifier (Q301) to detect noise.
Page 14
TK-7160 CIRCUIT DESCRIPTION ■ Unlock Circuit Transmitter System During reception, the 8RC signal goes high, the 8TC signal ■ Outline goes low, and Q44 turns on. Q43 turns on and a voltage is The transmitter circuit produces and amplifies the desired applied to the collector (8R).
Page 15
CIRCUIT DESCRIPTION ■ Key Matrix Circuit Control Circuit The TK-7160 front panel has function keys. Each of them The CPU carries out the following tasks: is connected to a cross point of a matrix of the KMI1 to KMO3 1) Controls the WIDE, NARROW, TX/RX outputs.
Page 16
TK-7160 CIRCUIT DESCRIPTION ■ Decode Power Supply Circuit The signal goes to EXTLIMIN (pin 5) of AQUA IC (IC241). When the power switch on the display unit is pressed, the The QT/DQT signal will pass through the low-pass filters in...
TK-7160 SEMICONDUCTOR DATA Microprocessor : 30622MEP-A01GP (TX-RX unit IC101) ■ Pin Function Pin No. Name Function Pin No. Name Function AMPSW AF AMP SW H : SW off, L : SW on QT/DQT QT/DQT output DTMF/MSK HSD/MSK/BEEP output Common data...
TK-7160 COMPONENTS DESCRIPTION Display Unit (X54-3510-10) Ref. No. Parts name Description Ref. No. Parts name Description Q242,243 Transistor AQUA beat shift LCD controller Q281 Digital transistor AF mute Transistor Dimmer function switch Q282 Transistor AF mute Transistor LCD backlit switch...
Les articles non mentionnes dans le Parts No. ne sont pas fournis. Y : AAFES (Europe) X : Australia M : Other Areas Teile ohne Parts No. werden nicht geliefert. TK-7160 (Y51-5060-XX) DISPLAY UNIT (X54-3510-10) TX-RX UNIT (X57-7080-10) Desti- Desti- Ref.
Page 20
TK-7160 PARTS LIST TX-RX UNIT (X57-7080-10) Desti- Desti- Ref. No. Address Parts No. Description Ref. No. Address Parts No. Description parts nation parts nation C46,47 CK73GB1H221K CHIP C 220PF C256 CK73GB1H331K CHIP C 330PF CK73GB1H102K CHIP C 1000PF C257 CC73HCH1H090B CHIP C 9.0PF...
Page 21
TK-7160 PARTS LIST TX-RX UNIT (X57-7080-10) Desti- Desti- Ref. No. Address Parts No. Description Ref. No. Address Parts No. Description parts nation parts nation C367 CC73GCH1H151J CHIP C 150PF C468 CK73GB1H221K CHIP C 220PF C368 CC73GCH1H270J CHIP C 27PF C469...
Page 22
TK-7160 PARTS LIST TX-RX UNIT (X57-7080-10) Desti- Desti- Ref. No. Address Parts No. Description Ref. No. Address Parts No. Description parts nation parts nation C618-620 CK73GB1H102K CHIP C 1000PF R92-1252-05 CHIP R 0 OHM J 1/16W C626 C93-0553-05 CHIP C 3.0PF...
Page 23
TK-7160 PARTS LIST TX-RX UNIT (X57-7080-10) Desti- Desti- Ref. No. Address Parts No. Description Ref. No. Address Parts No. Description parts nation parts nation R214 RK73HB1J334J CHIP R 330K 1/16W R307 RK73GB1J274J CHIP R 270K 1/16W R215 RK73HB1J222J CHIP R 2.2K...
Page 24
TK-7160 PARTS LIST TX-RX UNIT (X57-7080-10) Desti- Desti- Ref. No. Address Parts No. Description Ref. No. Address Parts No. Description parts nation parts nation R442 RK73GB1J271J CHIP R 1/16W ZSH5MA27 SURGE ABSORBER R443 RK73GB1J221J CHIP R 1/16W 1812L110PR VARISTOR R444...
Page 25
TK-7160 PARTS LIST TX-RX UNIT (X57-7080-10) Desti- Desti- Ref. No. Address Parts No. Description Ref. No. Address Parts No. Description parts nation parts nation Q441 2SK508NV(K52) Q442 2SJ347 Q443 KRX102U TRANSISTOR Q444 2SK508NV(K52) ✽ Q445 2SC3928A TRANSISTOR ✽ Q446 2SC5636...
TK-7160 EXPLODED VIEW M2.6 x 8 : N67-2608-48 M2 x 8 : N80-2008-48 M2.6 x 6 (Br-Tap) : N87-2606-48 M2.6 x 14 (Br-Tap) : N87-2614-48 Cx12 Display unit IC281 Q504 19x2 TX-RX unit Chassis Caution sticker (K only) S/No. label Caution sticker Parts with the exploded numbers larger than 700 are not supplied.
TK-7160 ADJUSTMENT Test Equipment Required for Alignment Test Equipment Major Specifications 1. Standard Signal Generator Frequency Range 136 to 175MHz (SSG) Modulation Frequency modulation and external modulation Output –127dBm/0.1µV to greater than –7dBm/100mV 2. Power Meter Input Impedance 50Ω Operation Frequency...
Page 29
TK-7160 ADJUSTMENT ■ Notes Adjustment Location • EEPROM ■ Switch The tuning data (Deviation, Squelch, etc.) for the EEP- ROM, is stored in memory. When parts are changed, re- Volume Channel up/down Display up/down Speaker adjust the transceiver. Power • AF PA IC (IC281) How to mounting the IC281.
Page 30
TK-7160 ADJUSTMENT Test Frequency 3 or 5 Reference Level Adjustment Frequency Channel RX (MHz) TX (MHz) Tuning point RX (MHz) TX (MHz) 155.05 155.10 136.05 136.10 136.05 136.10 Low’ 145.55 145.60 173.95 173.90 Center 155.05 155.10 155.00 155.10 High’ 164.55 164.60...
Page 31
TK-7160 ADJUSTMENT Measurement Adjustment Specifications/ Item Condition Test equipment Terminal Parts Method Remarks 4. RF 1) CH : RX center (Wide) Tra generator PC key Adjust the BPF waveform bandpass CH : RX low (Wide) Spectrum analyzer to Fig. 1...
Page 32
TK-7160 ADJUSTMENT Measurement Adjustment Specifications/ Item Condition Test equipment Terminal Parts Method Remarks ± 1.0W 3. High 1) CH : TX low Power meter PC key power CH : TX low’ CH : TX center CH : TX high’ CH : TX high 2) Transmit ±...
TK-7160 TERMINAL FUNCTION Name Function Name Function Battery voltage DC supply Ignition sens input DATAI External transmit signal input Ground DETO FM detector output DETO FM detector output TXAFI TX audio input from scrambler board FNC1 Programable I/O (programmed by FPU)
TK-7160 PC BOARD DISPLAY UNIT (X54-3510-10) Component side view (J72-0959-09) VOL UP POWER VOL DOWN HOOK MIC JACK DISPLAY UNIT (X54-3510-10) Foil side view (J72-0959-09) HOOK...
Page 35
TK-7160 PC BOARD DISPLAY UNIT (X54-3510-10) Component side view (J72-0959-09) Ref. No. Address CH UP CH DOWN Component side Layer 1 J72-0959-09 Layer 2 Foil side DISPLAY UNIT (X54-3510-10) Foil side view (J72-0959-09) Ref. No. Address J72-0959-09 BUSY POWER HOOK...
Page 36
TK-7160 TK-7160 PC BOARD PC BOARD DISPLAY UNIT (X54-3510-10) Component side view (J72-0959-09) DISPLAY UNIT (X54-3510-10) Component side view (J72-0959-09) Ref. No. Address VOL UP CH UP POWER VOL DOWN CH DOWN HOOK MIC JACK Component side Layer 1 J72-0959-09...
TK-7160 LEVEL DIAGRAM Receiver Section Center Frequency 49.95MHz 450kHz W : –78.5dBm N : –76.5dBm W : –121.5dBm W : –120.0dBm W : –106.5dBm W : –111.0dBm W : –110.5dBm W : –99.0dBm CF301 N : –121.5dBm N : –120.5dBm N : –106.5dBm...
Page 51
TK-7160 LEVEL DIAGRAM Audio Frequency 450kHz W : –93.5dBm N : –90.0dBm CF301 W : 0.58Vrms /CF302 N : 0.49Vrms 0.28Vrms 0.28Vrms 0.29Vrms 0.28Vrms 15mVrms 0.55Vrms 0.45Vrms IC321 IC201 IC241 IC213 IC241 IC241 IC201 IC281 vel meter. 2dB SINAD.) To make measurements in the AF section, connect the AC level meter.