Advertisement
NVR4020, NVR8040 Embedded Network Video Recorder Quick Setup Guide
This quick setup guide provides instructions to initially setup and use your new network video recorder. For additional information on the
extensive capabilities of your NVR, refer to the NVR4020, NVR8040 Embedded Network Video Recorder User Manual provided on CD
with your system.
NVR Front Panel
NVR8040, NVR4020 front panel
Item
Usage
Power: The POWER indicator turns green when NVR is powered on.
LED indicators
Status:
1. The light is green when the IR remote control is enabled
2. The light is red when the function of the composite keys (SHIFT) are used
3. The light is out when none of the above condition is met
Tx/Rx: TX/RX indicator flickers green when the network connection is functioning normally.
Infrared Sensor
Sensor for the remote control.
USB port
This port can be used for a portable mobile HDD, flash drive, DVD burner, or mouse. An additional USB port is located on the back panel.
NVR Backpanel
Camera (CH1 - CH4)
Monitor Out (HDMI, VGA)
USB
1
LED Indicators|
IR Sensor
USB port
Audio IN / OUT
ON / OFF switch
LAN
RS-485
Power connector
NVR4020 backpanel
NVR8040 backpanel
Item
Description
Camera (CH1 - CH4)
Network interface for IP cameras solely dedicated to the NVR. These cameras can only be accessed through the NVR. Each port provides
Power over Ethernet (PoE) power to the device connected to it. NOTE: Only 3SVision IP cameras can be attached to these channels.
Monitor Out (HDMI, VGA)
HDMI and DB15 (VGA) connector for monitor.
AUDIO IN / OUT
Not functional. Included for future expansion.
ON / OFF switch
Switch for powering the NVR on and off
USB
This port can be used for a portable mobile HDD, flash drive, DVD burner, or mouse. An additional USB port is located on the front panel.
RS-485 terminations
Not functional. Included for future expansion.
Power connector
Connector for standard 3-prong power cable.
Remote Control
The enter key on the remote control or the front panel has the same function as a mouse left click. The IR Range of the remote control is 10
meters. The buttons on the remote control correspond with the buttons on the front panel.
Item
Name
1
POWER
2
DEV
3
Alphanumeric Buttons
4
EDIT Button
5
A Button
Fan outlet
6
REC Button
7
PLAY Button
8
INFO Button
9
VOIP/MON button
10
MENU button
11
PREV button
17
13
12
10
8
6 4
18 16
15
14
11
9
7
5
3
Function
Power on/off the device.
Enables/Disables Remote Control.
Use for entering numerical data
Delete characters before cursor, check the checkbox and select the ON/OFF switch, start/stop record clipping in playback
Adjust focus in the PTZ Control menu, also used to switch between input methods (upper and lowercase alphabet, symbols
and numeric input).
Open the manual record interface
Playback, for direct access to playback interface.
Reserved.
Switch between main and spot output. In PTZ Control mode, it is used to zoom out the image.
Press the button will help you return to the Main menu (after successful login).
Press and hold the button for 5 seconds to turn off audible key beep.
In PTZ Control mode, the MENU/WIPER button will start wiper (if applicable).
Switch between single screen and multi-screen mode.
In PTZ Control mode, it is used to adjust the focus in conjunction with the A/FOCUS+ button.
1
2
NVR4020-8040_SQ
9/20/13
Advertisement
Table of Contents
Related Manuals for Observint NVR4020
Summary of Contents for Observint NVR4020
- Page 1 Item Description extensive capabilities of your NVR, refer to the NVR4020, NVR8040 Embedded Network Video Recorder User Manual provided on CD Camera (CH1 - CH4) Network interface for IP cameras solely dedicated to the NVR. These cameras can only be accessed through the NVR. Each port provides with your system.
-
Page 2: Step 1. Install The Nvr And Monitor
Connect an Ethernet drop cable between each camera and an RJ45 camera channel connector on the back of the NVR. Apply power to the cameras and allow at least 3 minutes for them to fully initialize. © 2013 Observint Technologies, Inc. All rights reserved. www.Observint.com... -
Page 3: Step 3. Using The Wizard For Basic Configuration Setup
Enter the admin password in the appropriate field. The default admin password is 12345. To change the admin password, check the New Admin Password checkbox, then enter the new password in the New Password and Confirm fields. www.Observint.com © 2013 Observint Technologies. All rights reserved. - Page 4 4 channels with the NVR4020 or 8 channels with the NVR8040. See “APPENDIX C Adding Cameras on the LAN to the NVR” on page <?> for procedural guidelines on adding these cameras.
-
Page 5: Step 4. Using The Menu System
Click Menu to open the menu system. A login window will open. In the Login window, select a User Name with administrative privileges, enter its password, then click OK. A window of Menu icons will open. For additional information about using your system, refer to the NVR4020, NVR8040 Embedded Network Video Recorder User Manual Live View display provided on CD with your system. -
Page 6: Specifications
Microsoft Internet Explorer 8.0, 9.0, and 10 (32-bit version), Mozilla Firefox 13 and higher and 3.6, Safari 5 and higher, Google Chrome Software Requirements Web Component Installation Mobile Client OS Platform iOS, Android (Guarding Expert) www.Observint.com © 2013 Observint Technologies. All rights reserved.