Kenwood KVT-827DVD Installation Manual
Monitor with dvd receiver
Hide thumbs
Also See for KVT-827DVD:
- Instruction manual (104 pages) ,
- Service manual (116 pages) ,
- Installation manual (72 pages)
Advertisement
Quick Links
KVT-827DVD
KVT-727DVD
KVT-627DVD
MONITOR WITH DVD RECEIVER
INSTALLATION MANUAL
MONITEUR AVEC REPTEUR DVD
MANUEL D'INSTALLATION
MONITOR MIT DVD RECEIVER
INSTALLATION-HANDBUCH
MONITOR MET DVD-ONTVANGER
INSTALLATIE HANDLEIDING
MONITOR CON RICEVITORE DVD
MANUALE DI INSTALLAZIONE
MONITOR CON RECEPTOR DVD
MANUAL DE INSTALACION
MONITOR COM RECEPTOR DVD
MANUAL DE INSTALAÇAO
© B54-4465-00/00 (EV/E2V)
Advertisement
Related Manuals for Kenwood KVT-827DVD
Summary of Contents for Kenwood KVT-827DVD
- Page 1 KVT-827DVD KVT-727DVD KVT-627DVD MONITOR WITH DVD RECEIVER INSTALLATION MANUAL MONITEUR AVEC REPTEUR DVD MANUEL D'INSTALLATION MONITOR MIT DVD RECEIVER INSTALLATION-HANDBUCH MONITOR MET DVD-ONTVANGER INSTALLATIE HANDLEIDING MONITOR CON RICEVITORE DVD MANUALE DI INSTALLAZIONE MONITOR CON RECEPTOR DVD MANUAL DE INSTALACION MONITOR COM RECEPTOR DVD MANUAL DE INSTALAÇAO...
- Page 2 Accessories ..1 ..2 ..1 ..1 ..1 ..1 ..1 ..1 ..1 ..2 * KVT-827DVD/727DVD only ..1 ..2 ..4 ..4 English...
-
Page 3: Installation Procedure
Installation Procedure 1. To prevent a short circuit, remove the key from the 2WARNING ignition and disconnect the - battery. • If you connect the ignition wire (red) and the 2. Make the proper input and output wire connections battery wire (yellow) to the car chassis (ground), for each unit. - Page 4 If you exceed the minimum bend limit, optical fibers within the optical cable may be damaged. An Optical cable (Accessory 3) is fixed with a chassis using harness band (Accessory $). (KVT-827DVD/727DVD only) For the sake of safety, be sure to connect the parking sensor.
- Page 5 Disc Changer etc. (Optional) Accessory 3 (KVT-827DVD/727DVD only) (Green) An Optical cable (Accessory 3) is fixed with a chassis using harness band Connection cable (Accessory $). (KVT-827DVD/727DVD (Included in the disc changer) only) Receiver unit (rear side) Optical input (KVT-827DVD/727DVD only) Connection cable...
- Page 6 Connecting the ISO Connector The pin arrangement for the ISO connectors depends on the type of vehicle you drive. Make sure to make the proper connections to prevent damage to the unit. The default connection for the wiring harness is described in 1 below. If the ISO connector pins are set as described in 2 or 3, make the connection as illustrated.
- Page 7 Connection for AV Equipments (KVT-827DVD/727DVD) PRE OUTPUT AV OUTPUT REAR FRONT AV INPUT 2 VIDEO R-CAM V-IN CENTER FM /AM ANTENNA AV INPUT 1 POWER VIDEO [MONO] VIDEO ■ Front Preout • Audio left output (White) • Audio right output (Red) ■...
- Page 8 Connection for AV Equipments (KVT-627DVD) PRE OUTPUT AV OUTPUT REAR FRONT R-CAM V-IN FM /AM ANTENNA AV INPUT POWER VIDEO VIDEO ■ Front Preout • Audio left output (White) • Audio right output (Red) ■ Rear Preout • Audio left output (White) •...
- Page 9 Installation for Monitor Unit Firewall or metal support Screw (M4X8) (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Accessory 6 Self-tapping screw Metal mounting strap (commercially available) (commercially available) Make sure that the unit is installed securely in place.
- Page 10 Removing Monitor Unit ■ Removing the Hard Rubber Frame (escutcheon) 1. Engage the catch pins on the removal tool 7 Removal Tool (Accessory 7) and remove the two locks on the lower level. Lower the frame and pull it forward as shown Catch in the figure.
- Page 11 Installation of Remote control unit ■ Install the remote control unit holder (Accessory @). Double-stick tape Remote control holder @ (included) To prevent the Remote control unit from dropping down under your foot, install it using the Remote control unit holder.If the Remote control unit drops down under driving pedals, it will interfere with your driving and may result in a traffic accident.