Related Manuals for Fujitsu FLASH-CAN-48P
Summary of Contents for Fujitsu FLASH-CAN-48P
-
Page 1: Evaluation Board
Fujitsu Semiconductor Europe FMEMCU-UG-900002-20 User Guide F²MC-16LX FAMILY EVALUATION BOARD FLASH-CAN-48P USER GUIDE Hardware Revision: V1.1... -
Page 2: Revision History
V1.8 Recycling Note added 05.09.2008 V1.9 MSc: China-RoHS regulation added 04.11.2011 V2.0 CCa: CE declaration added, Warranty and Disclamer updated. FME to FSEU update on the whole document. This document contains 33 pages. UG-900002-20 - 2 - © Fujitsu Semiconductor Europe GmbH... -
Page 3: Warranty And Disclaimer
The use of the deliverables (e.g. software, application examples, target boards, evaluation boards, starter kits, schematics, engineering samples of IC‟s etc.) is subject to the conditions of Fujitsu Semiconductor Europe GmbH (“FSEU”) as set out in (i) the terms of the License Agreement and/or the Sale and Purchase Agreement under which agreements the Product has been delivered, (ii) the technical descriptions and (iii) all accompanying written materials. -
Page 4: Table Of Contents
LIN”A” Interface connector (X8) ................24 CAN”A” Interface connector (X10) ................. 24 USER-LEDs & LC-Display (optional) ..............24 VG96 connector (X4) ..................... 25 6 SILK-PLOT OF THE BOARD ..................27 7 RELATED PRODUCTS ....................28 UG-900002-20 - 4 - © Fujitsu Semiconductor Europe GmbH... - Page 5 FLASH-CAN-48P Contents 8 INFORMATION IN THE WWW..................29 9 EU-KONFORMITÄTSERKLÄRUNG / EU DECLARATION OF CONFORMITY ..... 30 10 CHINA-ROHS REGULATION ..................31 11 RECYCLING ........................33 © Fujitsu Semiconductor Europe GmbH - 5 - UG-900002-20...
-
Page 6: Overview
Chapter 1 Overview 1 Overview 1.1 Abstract The FLASH-CAN-48P is a low cost multifunctional evaluation board for 16-Bit Fujitsu Flash microcontrollers with FPT-48P-M26 package. It can be used stand alone for software development and testing or as a simple target board to work with the emulator system. -
Page 7: General Description
FLASH-CAN-48P Chapter 1 Overview 1.3 General Description The FLASH-CAN-48P is designed to support 16Bit microcontrollers with 48-pin LQFP package like MB90360 Series, MB90385 Series, MB90455 Series, MB90895 Series, and MB90960 Series. It can be used as a stand alone evaluation board or as a target board for emulator debugger. -
Page 8: Installation
Do not screw the cover too tight (max 0.054 Nm). If you have connectivity problems then please loosen the screws and tighten again the screws equally. Do not clean NQPACK, YQPACK, and YQSOCKET with steam. Cleaning material will contaminate inside of connector. UG-900002-20 - 8 - © Fujitsu Semiconductor Europe GmbH... -
Page 9: Jumpers And Switches
F 10 JP34 MCU_VCC Jumper 2pol closed E 12 JP35 Reset inverter Jumper 3 pol H 19 JP36 X0A select Jumper 3 pol JP37 X1A select Jumper 3 pol © Fujitsu Semiconductor Europe GmbH - 9 - UG-900002-20... - Page 10 FLASH-CAN-48P Chapter 3 Jumpers and Switches LIN”A” UG-900002-20 - 10 - © Fujitsu Semiconductor Europe GmbH...
-
Page 11: Operating-Mode (S2)
(MB90360/960 Series: P83 and P84) have to be connected manually to GND in case of asynchronous programming (see chapter 4). MD0 MD1 MD2 nc P31 P30 P84 P83 Dip-Switch S2 (default setting) © Fujitsu Semiconductor Europe GmbH - 11 - UG-900002-20... -
Page 12: Power Supply Voltage (Jp: 29, 34)
OFF (open) Disconnected from Power supply Vcc Default: JP29 = 1-2, JP30 = OFF, JP34 = ON, By default, the on-board Voltage +5V regulation is used and the microcontroller is powered. UG-900002-20 - 12 - © Fujitsu Semiconductor Europe GmbH... -
Page 13: Analogue Power Supply Voltage (Jp: 11, 13, 15)
(AVcc and AVss) to the A/D-converter. If JP13 is open, the resistors R11 and R23 define AVRH. By default, the resistor divider (R11 and R23) is not mounted on the board. © Fujitsu Semiconductor Europe GmbH - 13 - UG-900002-20... -
Page 14: Subclock (Jp: 36,37)
Pin 47 is connected to the 32kHz Subclock (X1A) JP37 (X1A/P36) Pin 47 is used as P36 and is connected to X4-C29 Default: JP36: 1-4, JP37: 1-2 By default, the 32kHz-subclock-crystal is connected to the microcontroller. UG-900002-20 - 14 - © Fujitsu Semiconductor Europe GmbH... -
Page 15: Uart"A" (Jp: 1, 2, 31)
RTS and CTS is not shortcut on X5 Default: JP6=OFF, JP8=OFF, JP32 = OFF By default, UART0 is not connected. (UART0 would only be available for MB90360, MB90895, and MB90960 Series) © Fujitsu Semiconductor Europe GmbH - 15 - UG-900002-20... -
Page 16: Lin"A" (Jp: 17, 18, 21, 22)
JP1 and JP2 are open if JP21 and JP22 are closed. 3.9 CAN“A” (JP: 25, 26) One high-speed CAN-transceiver is available on the FLASH-CAN-48P evaluation board. JP25, JP26 connects the CAN-Port to the CAN-transceiver (U7, X10). If the CAN interface is not used, the jumpers should be left open. -
Page 17: Reset-Generation (Jp: 3, 4, 24, 35)
If JP35 (Polarity) is set, than JP4 together with JP3 or JP5 have to be set, too. If the reset LED is steadily on, check the power supply input voltage and the settings for the reset-generation by UART. © Fujitsu Semiconductor Europe GmbH - 17 - UG-900002-20... -
Page 18: Buttons Int4, Int5, Tin0, In0, Adtg, Reset (Jp: 12, 14, 16, 20, 23, 24)
MB90960 Series: ADTG is connected to Push-button “ADTG” Open No connection to Push-button ADTG Push-button “Reset” is active Closed JP24 (Reset) Open No external Reset generation Default: JP12, JP14, JP16, JP20, JP23, JP24 = Closed UG-900002-20 - 18 - © Fujitsu Semiconductor Europe GmbH... - Page 19 FLASH-CAN-48P Chapter 3 Jumpers and Switches By default, INT4, INT5, TIN0, IN0 and ADTG of the microcontroller are connected to the Push buttons and the external Reset-generation is active. © Fujitsu Semiconductor Europe GmbH - 19 - UG-900002-20...
-
Page 20: Programming The Internal Flash
In order to program the Flash-ROM asynchronously via UART1, the tool “Fujitsu Flash MCU Programmer for FMC16LX” can be used. This tool is available free on the Fujitsu Micros CD- ROM or Web Site (http://www.fme.gsdc.de/gsdc.htm: select Software Utilities) The following procedure must be followed to enable Flash Programming: 1. - Page 21 MD0 MD1 MD2 nc P31 P30 P84 P83 Single-Chip Run Mode 9. Power on the board. The user application is started directly. Boot 4MHz RESET UART “A” © Fujitsu Semiconductor Europe GmbH - 21 - UG-900002-20...
-
Page 22: Synchronous Mode
Please contact our Web Site in order to get more information about the FlashKit-Tool: http://www.fme.gsdc.de/gsdc.htm: select Tools Programme MCU FlashKit A dedicated Flash programming socket (X17) is provided on the FLASH-CAN-48P board for direct connection to the Fujitsu „FlashKit‟. -
Page 23: Connectors
The DTR or RTS signal can be used to generate a reset. Please use 1:1 cable for PC-connection. Note: UART”B” (X5) is only available within CTS RTS DSR MB90895 Series, MB90360, and MB90960 Series. Connector X3, X5: © Fujitsu Semiconductor Europe GmbH - 23 - UG-900002-20... -
Page 24: Lin"A" Interface Connector (X8)
P31 have to be connected manually to GND. See chapter 4 for more details. Instead of the user-LEDs one alphanumeric LC-Display (optional) can be connected. The following control-signals are reserved: VCC GND 90360 90960 90385 90455 90895 UG-900002-20 - 24 - © Fujitsu Semiconductor Europe GmbH... -
Page 25: Vg96 Connector (X4)
P52/AN3 P53/AN3 P63/AN3 P53/AN3 P54/AN4 P64/AN4 P54/AN4 P55/AN5 P65/AN5 P55/AN5 P56/AN6 P66/AN6/PPGC P56/AN6 P57/AN7 P67/AN7/PPGE P57/AN7 AVcc AVss P60/INT0 P63/INT3 RSTX RSTX RSTX P00/AD00 P01/AD01 P02/AD02 P03/AD03 P04/AD04 P05/AD05 P06/AD06 P07/AD07 © Fujitsu Semiconductor Europe GmbH - 25 - UG-900002-20... - Page 26 P87/SCK1 P41/SCK1 P42/SOT1 P86/SOT1 P42/SOT1 P43/(TX) P43/TX1 P43/TX P44/(RX) P42/RX1/INT9R P44/RX only CAN devices (MB90360, 90385, MB90895 Series) only single-clock device (MB90F38xS /MB90F45xS / MB90F36xS) only MB90360, MB90895, and MB90960 Series UG-900002-20 - 26 - © Fujitsu Semiconductor Europe GmbH...
-
Page 27: Silk-Plot Of The Board
Pin 48 Pin 2 90F387 Pin 24 Pin 26 Pin 23 Pin 25 4MHz FlashKit Power- Jack MAX232 optional: LCD UART”B” User-LEDs (P30-33, P54-57) INT4 INT5 TIN0 ADTG Reset CAN”A” UART”A” LIN”A” © Fujitsu Semiconductor Europe GmbH - 27 - UG-900002-20... -
Page 28: Related Products
Evaluation chip for MB90340 / 350 / 360 / 960 Series MB90V340A-101 Single-clock version MB90V340A-102 Dual-clock version NQPACK48SD Socket for package FPT-48P-M26 (Tokyo Eletech Corp. www.tetc.co.jp/e_tet.htm) HQPACK48SD Header for NQPACK48SD UG-900002-20 - 28 - © Fujitsu Semiconductor Europe GmbH... -
Page 29: Information In The Www
Microcontrollers (8-, 16- and 32bit), Graphics Controllers Datasheets and Hardware Manuals, Support Tools (Hard- and Software) http://mcu.emea.fujitsu.com/ Power Management Products http://www.fujitsu.com/emea/services/microelectronics/powerman/index.html Media Products: SAW filters, acoustic resonators and VCOs http://www.yuden.co.jp/us/product/device/device00.html For more information about FUJITSU SEMICONDUCTOR http://emea.fujitsu.com/semiconductor © Fujitsu Semiconductor Europe GmbH - 29 - UG-900002-20... -
Page 30: Eu-Konformitätserklärung / Eu Declaration Of Conformity
9 EU-Konformitätserklärung / EU declaration of conformity Hiermit erklären wir, Fujitsu Semiconductor Europe GmbH, Pittlerstrasse 47, 63225 Langen, Germany dass dieses Board aufgrund seiner Konzipierung und Bauart sowie in den von uns in Verkehr gebrachten Ausführung(en) den grundlegenden Anforderungen der EU-Richtlinie 2004/108/EC „Elektromagnetische Verträglichkeit“... -
Page 31: China-Rohs Regulation
“Year”. © Fujitsu Semiconductor Europe GmbH - 31 - UG-900002-20... - Page 32 X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in SJ/T11363-2006. Data listed in the table represents best information available at the time of publication UG-900002-20 - 32 - © Fujitsu Semiconductor Europe GmbH...
-
Page 33: Recycling
According to the European WEEE-Directive and its implementation into national laws we take this device back. For disposal please send the device to the following address: Fujitsu Semiconductor Europe GmbH Warehouse/Disposal Monzastraße 4a D-63225 Langen GERMANY © Fujitsu Semiconductor Europe GmbH - 33 - UG-900002-20...