Table of Contents
Advertisement
Quick Links
- 1 Wired Remote Controller and Accessories
- 2 Installing the Communication and Power Cables
- 3 Installing the Wired Remote Controller
- 4 Setting the Wired Remote Controller Options
- 5 Wired Remote Controller Error Codes
- 6 Service Mode
- 7 Setting the Indoor Unit Option Code
- 8 Checking the Indoor Unit Option Switch Settings
- Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for Samsung MWR-WS00
Summary of Contents for Samsung MWR-WS00
- Page 1 INSTALLATION MANUAL Wired Remote Controller MWR-WS00 System Air Conditioner G R A DB98-25180A(1)
-
Page 2: Safety Precautions
Safety Precautions This installation manual describes how to install the Wired Remote Controller. For installation of other optional accessories, refer to the appropriate installation manual. R ead carefully this installation manual before WARNING installation and check if the Wired Remote Controller is installed correctly after installation. -
Page 3: Table Of Contents
Contents ........4 IRED EMOTE ONTROLLER AND CCESSORIES Accessories ....................4 ........5 NSTALLING THE IRED EMOTE ONTROLLER Installing the communication and power cables ....5 Installation ....................6 Setting the Wired Remote Controller Options ....... 7 ... -
Page 4: Wired Remote Controller And Accessories
Wired Remote Controller and Accessories Accessories The following accessories are supplied with the air conditioner. The number of each accessory is indicated in parentheses. Power Drawing Cable Cable Tie (2) Cable Clamp(4) M4X16 Screw(5) Communication cable Wire joint (4) User's manual(1) Communication and power cable (1) -
Page 5: Installing The Wired Remote Controller
Installing the Wired Remote Controller Installing the communication and power cables I f the power cable for the wired remote controller is installed inside the indoor unit, the power cable supplied with the wired remote controller need not to be installed. ... -
Page 6: Installation
Installing the Wired Remote Controller (Continued) Installation Open the wired remote controller by pushing up the top cover of the remote controller while holding the rear cover firmly. Install the rear cover of the wired remote controller on the wall with the screws supplied. -
Page 7: Setting The Wired Remote Controller Options
Setting the Wired Remote Controller Options Switch ��� ��� ��� ��� ��� ��� ��� ��� Switch OFF Switch ON SW1 Cooling and Heating Cooling Only � � � ��� � � � � Allow wireless remote Disable the wireless remote controller controller Master remote... -
Page 8: Wired Remote Controller Error Codes
Installing the Wired Remote Controller (Continued) Wired Remote Controller Error Codes The error codes of the indoor and outdoor units are displayed on the wired remote controller. Refer to the indoor and outdoor unit technical manuals for the error codes reference. The following error codes are related to the wired remote controller. -
Page 9: Group Control
Group Control U sing one wired remote controller for a group of indoor units. Outdoor unit COM1 COM1 COM1 Indoor unit COM2 COM2 Wired remote controller Outdoor unit Indoor unit Outdoor unit Wired remote controller Indoor unit Note ... - Page 10 Installing the Wired Remote Controller (Continued) Using 2 wired remote controllers 2 wired remote controllers can be used to control a single indoor unit or a group of indoor units. Outdoor unit COM1 Indoor unit COM2 Wired remote controller Wired remote controller (Master) (Slave)
-
Page 11: Additional Functions
Additional Functions Service Mode T he wired remote controller supports the following service modes. Menu Description Monitoring and setting the indoor unit option code Monitoring and setting the indoor unit RMC address Monitoring the indoor unit cycle data Setting the indoor unit temperature sensor compensation Setting the RPM compensation Setting the EEV step when the indoor unit is off during... -
Page 12: Setting The Indoor Unit Option Code
Additional Functions (Continued) Setting the Indoor Unit Option Code In order to set the indoor unit option code using the wired remote controller, hold down the buttons and button at the same time for 5 seconds. The menu will display . -
Page 13: Setting The Rmc Address
Setting the RMC Address In order to set the RMC address of the indoor unit using the wired remote controller, hold down the buttons and the button at the same time for 5 seconds. The menu will display Press the button and the menu will display Press the button. -
Page 14: Monitoring The Indoor Unit Cycle Data
Additional Functions (Continued) Monitoring the Indoor Unit Cycle Data In order to monitor the indoor unit cycle data using the wired remote controller, hold down the buttons and button at the same time for 5 seconds. The menu will display Press the button twice and the menu will display Press the... -
Page 15: Compensating For The Wired Remote Controller Temperature Sensor
Compensating for the Wired Remote Controller Temperature Sensor In order to compensate for the temperature sensor of the wired remote controller, hold down the buttons and button at the same time for 5 seconds. The menu will display Press the button until is displayed. -
Page 16: Rpm Compensation
Additional Functions (Continued) RPM Compensation In order to compensate for the RPM using the wired remote controller, hold down the buttons and button at the same time for 5 seconds. The menu will display Press the button until is displayed. Press the button. -
Page 17: Eev Step Setup When The Indoor Unit Is Off During Heating Mode
EEV step setup when the indoor unit is off during heating mode In order to set the EEV step for when the indoor unit is off during heating mode using the wired remote controller, hold down the buttons and the button at the same time for 5 seconds. -
Page 18: Setting The Filter Time
Additional Functions (Continued) Setting the Filter Time In order to set the filter time of the indoor unit using the wired remote controller, hold down the buttons and button at the same time for 5 seconds. The menu will display Press the button until is displayed. -
Page 19: Heating Capacity Compensation
Heating Capacity Compensation In order to compensate for the heating capacity using the wired remote controller, hold down the buttons and button at the same time for 5 seconds. The menu will display Press the button until is displayed. Press the button. -
Page 20: Checking The Indoor Unit Option Switch Settings
Additional Functions (Continued) Checking the Indoor Unit Option Switch Settings In order to check the indoor unit option switch settings using the wired remote controller, hold down the buttons and the button at the same time for 5 seconds. The menu will display Press the button and select the appropriate menu referring to the table below. - Page 21 Memo...