When Q1103 or Q1104 is shorted between their terminals, the laser diodes for DVD or CD will radiate beam. If the top cover is removed with no disc loaded while such short-circuit is continued, the naked eyes may be exposed to the laser beam. AVH-P5200BT/XNUC...
Page 3
CAUTION Danger of explosion if battery is incorrectly replaced. Replaced only with the same or equivalent type recommended by the manufacture. Discord used batteries according to the manufacture's instructions. AVH-P5200BT/XNUC...
Page 4
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. AVH-P5200BT/XNUC...
“Plug the supplied microphone securely into the jack” may appear due to the measurement failure. 11. EJECT LOCK MODE for DVD mechanism How to enter : Reset with [FORWARD] key and [EJECT] key pressed. Unlocked by turning ACC ON or reset. AVH-P5200BT/XNUC...
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting temperatures (hard to melt/easy to harden). The following lead-free solders are available as service parts: Parts numbers of lead-free solder: GYP1006 1.0 in dia. GYP1007 0.6 in dia. GYP1008 0.3 in dia. AVH-P5200BT/XNUC...
2. SPECIFICATIONS 2.1 SPECIFICATIONS AVH-P5200BT/XNUC, AVH-P5200DVD/XNUC General Slope........–12 dB/oct Subwoofer (mono): Power source......14.4 V DC (10.8 V to 15.1 V Frequency......50/63/80/100/125 Hz allowable) Slope........–18 dB/oct Grounding system....Negative type Gain ........+6 dB to –24 dB Maximum current consumption Phase .........Normal/Reverse ............10.0 A...
Page 9
Frequency range..... 530 kHz to 1 710 kHz (10 kHz) Usable sensitivity....25 μV (S/N: 20 dB) Signal-to-noise ratio....62 dB (IHF-A network) Bluetooth (AVH-P5200BT) Version ........Bluetooth 2.0 certified Output power ......+4 dBm Max. (Power class 2) CEA2006 Specifications Power output ......14 W RMS ×...
Page 10
Frequency......40/80/200/400/1k/2.5k/8k/ (Ver. 8.2 and earlier) 10k Hz DivX decoding format....Home Theater Ver. 3, 4, 5.2, Gain ........±12 dB 6 (.avi, .divx) HPF: Frequency......50/63/80/100/125 Hz Slope........–12 dB/oct Compatible physical format Subwoofer (mono): ...........Version 1.1 Frequency......50/63/80/100/125 Hz AVH-P5200BT/XNUC...
Page 11
530 kHz to 1 640 kHz (10 kHz) Usable sensitivity....25 μV (S/N: 20 dB) Signal-to-noise ratio....62 dB (IEC-A network) Infrared remote control Wavelength........945 nm Output ......... typ; 10 mw/sr per Infrared Note Specifications and the design are subject to mod- ifications without notice. AVH-P5200BT/XNUC...
Page 12
..........Version 1.1 Gain ........±12 dB Maximum memory capacity HPF: ..........2 GB Frequency....... 50/63/80/100/125 Hz File system......FAT12, FAT16, FAT32 Slope........–12 dB/oct MP3 decoding format ..MPEG-1 & 2 Audio Layer 3 Subwoofer (mono): Frequency....... 50/63/80/100/125 Hz Slope........–18 dB/oct AVH-P5200BT/XNUC...
Page 13
Version ........Bluetooth 2.0 certified Output power ......+4 dBm Max. (Power class 2) Infrared remote control Wavelength......945 nm Output ........typ; 10 mw/sr per Infrared Note Specifications and the design are subject to mod- ifications without notice. AVH-P5200BT/XNUC...
(BT model only) The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Pioneer Corporation is under license. Other trademarks and trade names are those of their respective owners. AVH-P5200BT/XNUC...
2.3 PANEL FACILITIES Head unit CAUTION • Use an optional Pioneer USB cable (CD-U50E) to connect the USB audio player/USB mem- ory as any device connected directly to the unit will protrude out from the unit and may be dangerous.
Press to return to the Press and hold to turn previous track (chap- the rear source off. ter). Press to go to the next track (chapter). Press to stop play- back. Press to select the / (FOLDER/P.CH) next/previous disc/ folder. AVH-P5200BT/XNUC...
Switch PCB Unit Panel PCB DVD Amp Unit Main PCB Unit BT Model Monitor PCB Volume PCB Unit Keyboard PCB Switch PCB Unit Panel PCB DVD Amp Unit (Service) Main PCB Unit BT PCB BT ANT PCB Tuner Box Unit AVH-P5200BT/XNUC...
Page 26
H:AVH-P5200BT/XNUC I:AVH-P5250BT/XNRD B:AVH-P5200DVD/XNUC C:AVH-P5250DVD/XNRC D:AVH-P5250DVD/XNRD E:AVH-P5250DVD/XNRI Unit Number CXX2838(H) Unit Number CXX2839(I) Unit Name DVD Amp Unit(Service) Unit Number CWN4979(B) Unit Number CWN4980(C) Unit Number CWN4981(D) Unit Number CWN4982(E) Unit Name DVD Amp Unit Unit Number CWN3129(H,B) Unit Number CWN3130(I,C,D,E)
DVD Mechanism Module and Drive Unit Grease GEM1043 DVD Mechanism Module and Drive Unit Locking agents 1401M DVD Mechanism Module (1401M:produced by THREE BOND) Grease GEM1011 Drive Unit Grease GEM1047 Drive Unit Grease GEM1071 Drive Unit Grease GEM1072 Drive Unit AVH-P5200BT/XNUC...
Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools: Portions to be cleaned Cleaning tools DVD pickup lenses Cleaning liquid : GEM1004 Cleaning paper : GED-008 Portions to be cleaned Cleaning tools Fans Cleaning paper : GED-008 AVH-P5200BT/XNUC...
ASENBO <- H DDCCLK <- Clock Out DDCCLK : Pin92 (Frequency of 370 kHz) VD5 <- H VD5, 8 : Pin113, 114 VD8 <- H Starts Communication with Display microcomputor Source Keys operartive Source ON SYSPW : Pin130 SYSPW <- H AVH-P5200BT/XNUC...
To “Replace pickup” Check 3 Check measured value of error ratio * Make sure to avoid any unwiped spots or actuator breakage. Check error ratio Lens cleaning Clean lens Within prescribed completed? value? To “Replace pickup” No problem found in pickup AVH-P5200BT/XNUC...
Page 42
Remarks: LD current value (ref.) GGV1025 DVDLD1-VCC5_3 60~390(mV) 10~65(mA) DVDLD1 VCC5_3 Disc used Spot to check Rated value Remarks: LD current value (ref.) TCD-782 CDLD1-VCC5_3 60~360(mV) 10~60(mA) VCC5_3 CDLD1 Mind breakage of a laser diode caused by static electricity. AVH-P5200BT/XNUC...
Page 43
Check the error ratio of a specified ID in the tracking closed status in the test mode. Disc used Spot to check Rated value Remarks: GGV1025 ID : 40000 1.000E-3 or less GGV1025 ID : 200000 1.000E-3 or less TCD-782 ID : Home position 2.500E-3 or less Error ratio: 0.742E-5 in this case AVH-P5200BT/XNUC...
IC but a core unit (as no key or others is written in a Go to FE Check flash alone). Normal? Go to FE Check Go to FE-related FE part normal? repair Replace unit Normal? AVH-P5200BT/XNUC...
Page 45
Check the voltage of the sending pin when the power is ON. Checking should be based on DGND. Spot to check Module NO. Rated value Unit 1 STANDBY-DGND1 VCC33-0.6V or more PCB side A STANDBY DGND1 Fig. 1.1: Spots to check in STANDBY AVH-P5200BT/XNUC...
Page 46
Unit 1 VDD5_2 - DGND1 5.0 ± 0.4 2 VCC33_1 - DGND1 3.3 ± 0.15 3 VCC12-1 - DGND1 1.2 ± 0.12 PCB side A VCC12-1 VDD5_2 VCC33_1 DGND1 Fig. 2.2: Spots to check in VDD5, VCC33, VCC12 voltages AVH-P5200BT/XNUC...
Page 47
Check the voltage of the sending pin when the power is ON. Checking should be based on DGND. Spot to check Module NO. Rated value Unit 1 NRES-DGND1 VCC33 x 0.7 or more PCB side A NRES DGND1 Fig. 3.1: Spots to check in RESET AVH-P5200BT/XNUC...
Page 48
Check the voltage of the sending pin when the power is ON. Checking should be based on DGND. Spot to check Module NO. Rated value Unit 1 VSENS - DGND1 VCC33 x 0.7 or more PCB side A DGND1 VSENS Fig. 4.2: Spots to check in VSENS AVH-P5200BT/XNUC...
Page 49
Spot to check Module NO. Rated value Unit 1 IC1501 156pin 27 MHz ± 50ppm Rated value Fig. 5.2: Rated value of a clock PCB side A DGND1 IC1501 156pin Fig. 5.3: Spots to check in 27 MHz AVH-P5200BT/XNUC...
Page 51
PCB side B Spot to check 1 (IC1480) PCB side A Spot to check 2 (IC1501) Fig. 6.2: Spots to check in SDRAM I/F AVH-P5200BT/XNUC...
Page 52
Rated value Unit 1 VD8_1 - PGND3 8.0 ± 0.4 2 VD - PGND_3 8.0 ± 0.4 3 VCC5_1 - AGND1 5.0 ± 0.1 PCB side A VD8_1 PGND3 AGND1 VCC5_1 Fig. 7.2: Spots to check in VD8, VCC5 voltages AVH-P5200BT/XNUC...
Page 53
Checking should be based on PGND, AGND. Spot to check Module NO. Rated value Unit 1 VD - PGND_3 8.0 ± 0.4 2 AVCC5 - GNDAU1 5.0 ± 0.1 PCB side A PGND3 GNDAU1 AVCC5 Fig. 8.2: Spots to check in VD8, AVCC5 voltages AVH-P5200BT/XNUC...
Page 54
Rated value 3 1 DACCK 2.0 V~VCC33V DGND~0.8 V 36.8640 MHz ± 300 ppm 2 DACCK 2.0 V~VCC33V DGND~0.8 V 33.8688 MHz ± 300 ppm Rated value 1 Rated Rated value 2 value 3 Fig. 9.2: Rated value of a clock AVH-P5200BT/XNUC...
Page 55
PCB side A Spot to check 2 (IC1501 148pin) Spot to check 1 (probe) Fig. 9.3: Spots to check in 27 MHz, DACCLK AVH-P5200BT/XNUC...
Page 56
VCC33V-0.6V or more 0.4V or less Waveform 1 2 SRCK VCC33V-0.6V or more 0.4V or less Waveform 2 3 LRCK VCC33V-0.6V or more 0.4V or less Waveform 3 Rated value 2 Rated value 1 Fig. 10.2: Rated value of serial three wires AVH-P5200BT/XNUC...
Page 57
Spot to check 1 (sending pin) Rated value (rms) Reference waveform 4 LO 1400 ± 150 mV Waveform 4 5 RO 1400 ± 150 mV Waveform 4 Rated value is an effective value (rms) Fig. 10.4: Rated value of analog audio out (LO, RO) AVH-P5200BT/XNUC...
Page 58
Checking should be performed after connecting 24Pin FFC to the jig or other equipment. Spot to check 1 (sending pin) Rated value 1 Rated value 2 Reference waveform 6 IEC VCC33V-0.6V or more 0.4V or less Waveform 5 PCB side A Fig. 10.6: Spot to check in digital audio signal (IECOUT) AVH-P5200BT/XNUC...
Page 59
PEAK COMPOSITE signal Rated value Color burst Pedestal level BOTTOM Horizontal synchronous signal Fig. 11.2: Waveform when 100% composite white is output PCB side A COMPOSITE Fig. 11.5: Spot to check in VIDEO signal AVH-P5200BT/XNUC...
Page 60
(For how to display the LD live time, see FE Test Mode) 2. The second digit of the live time from the left being E as in “*E** ****” means the FLASH memory has reached the end of its life. E.g.: AVH-P5200BT/XNUC...
*4 Available only for the models compatible with DVD-A. In case of an error, the audio output will be muted only but the playback operation will continue. Also, acceptance of the user operation will be the same as normal. AVH-P5200BT/XNUC...
Page 63
The time taken for occurrence should be specified in the latency time for the audio property notice set in the connection confirmation command. *10 This occurs when the DRM information update notice is sent from the DVD mecha but no DRM information update response is returned. AVH-P5200BT/XNUC...
Page 73
Middle DVD: Middle Select CD Search destination CRG home position 5 Select CRG Move Select completed Select 5 Select Return CRG transfers to the outermost circumference <In case of an error> Select <In case of an error in Power_OFF> AVH-P5200BT/XNUC...
Page 74
Test mode command NULL * In CRG+/-, operation stops when the key is released. At that time, the DVD mecha should make the key command request (TP = B1h) on a regular basis to prevent any omission of key release. AVH-P5200BT/XNUC...
Page 75
D1 = 03h, set the TE offset coefficient to D2 – D9 and transmit [1 second later] D1 = 07h, set the DBAL coefficient to D2 – D9 and transmit [1 second later] D1 = 01h, after setting the status display data to D2 – D9 and transmitting, wait for keys AVH-P5200BT/XNUC...
Page 76
End displaying RF level value Tracking Close status (3),(4) Measure Switch playback Power Off Focus Jump ID Search T.Jump Tracking Open error ratio speed Note 3 Note 4 (1)-(4) Specify No. Specify ID of tracks Start ID search Start jumping AVH-P5200BT/XNUC...
Page 77
Register set time set time [How to specify a set time] Specify a digit with the commands (1) and (2). Commands (3) and (4) are to increase/decrease the number. Determine with the command (5). Cancel with the command (8). AVH-P5200BT/XNUC...
Choose "Version Check" among the monitor test mode menu screen. [Display specifications] When 8 digits of read number is strange, displayed with red. [Operation specification] Operational description Remote controller key Return to test mode menu Page up Page down AVH-P5200BT/XNUC...
Page 79
In case the EEPROM initialization has been performed. In case the adjustment value has been initialized. Calibration inspection : In case the calibration inspection has never been performed. In case the EEPROM initialization has been performed. In case the adjustment value has been initialized. AVH-P5200BT/XNUC...
Page 80
X/Y information of [MIN] and [MAX] of the outermost circumference are displayed. [BEFOR] indicates the value stored in the EEPROM. [AFTER] indicates MIN/MAX of the A/D value currently captured. [Operation specification] Operational description Remote controller key Return to top menu AVH-P5200BT/XNUC...
Page 81
Order of display of the locations to be pressed. This point is intended to end the calibration inspection, and therefore, the corrected value of this point is not obtained. [Operation specification] Operational description Remote controller key Return to top menu AVH-P5200BT/XNUC...
Page 82
: The coordinate (X direction, Y direction) which is the result of adding the correction by calibration to the normalized coordinate is displayed. Movable "+" cursor is displayed in red. 16 calibration points are displayed in white. [Operation specification] Operational description Remote controller key Return to top menu AVH-P5200BT/XNUC...
Page 83
The incorrect touch will make the characters of cursor turn red. Repeat this for 4 points, and “OK” is displayed upon the last press of 4th point. [Display specifications] confirming The pushing order [Operation specification] Operational description Remote controller key Return to top menu AVH-P5200BT/XNUC...
Page 84
When the adjusted value has been initialized (Data initialize). When the EEPROM has been initialized. [Operation specification] Operational description Remote controller key Selection cursor up movement Selection cursor down movement Return to test mode menu Menu enter AVH-P5200BT/XNUC...
Page 85
When normally ends, "success" is displayed. When will not end in four seconds, judged to be abnormal, "failure" is displayed. [Operation specification] Operational description Remote controller key Selection cursor left movement Selection cursor right movement Return to test mode menu Menu enter AVH-P5200BT/XNUC...
Page 86
[MONOCHROME STRIPE] Display of monochrome stripe signal (1dot Width) [Operation specification] Operational description Remote controller key Return to test mode menu [COLOR BAR] Display of color bar signal [Operation specification] Operational description Remote controller key Return to test mode menu AVH-P5200BT/XNUC...
Page 87
Display of Black/White signal [Operation specification] Operational description Remote controller key Return to test mode menu Next signal [CENTER MARKER] Display of signal for screen central location setting. [Operation specification] Operational description Remote controller key Return to test mode menu AVH-P5200BT/XNUC...
Slide the grille forward by pushing two tabs with tweezers or other item. Attach and remove the grille unit by sliding it horizontally. How to assemble Grille Unit As the mother unit SD part is fixed with the grille, insert it horizontally. Fig.1 AVH-P5200BT/XNUC...
Page 89
How to separate the Drive Unit and the (Rear Side) Chassis Assy (Fig. 2) Remove the seven screws and then sepa- rate the Drive Unit and the Chassis Assy. (Left Side) Drive Unit Chassis Assy (Right Side) Fig.2 AVH-P5200BT/XNUC...
Page 90
Remove the four screws and then lift the Bracket toward the Drive Unit. Drive Unit DVD Mechanism Module Remove the four screws. Disconnect the connector and then remove the DVD Mechanism Module. Drive Unit Disconnect the two connectors and then remove the Drive Unit. Fig.3 AVH-P5200BT/XNUC...
Page 91
Holder. Holder Fig.4 Removing the DVD Amp Unit (Fig.5) Remove the three screws. Disconnect the connector. (Only BT model) Straighten the tabs at three locations indi- cated and then remove the DVD Amp Unit. DVD Amp Unit Fig.5 AVH-P5200BT/XNUC...
Page 92
Removing the Motor Unit, the Drive Unit can operate to lead to the Monitor Assy. Motor Unit Remove the two screws and then remove the two Guids(Right side, Left side). Pull out the Monitor Assy in the direction indicated by an arrow. Fig.6 AVH-P5200BT/XNUC...
Page 93
Disconnect the connector. Case Unit Cover Keyboard PCB Disconnect the three connectors. Straighten the tabs at two locations indi- cated and then remove the Monitor Unit. Remove the screw. Disconnect the connector and then remove the Keyboard PCB. Monitor Unit AVH-P5200BT/XNUC...
Page 94
LCD plate Insert the tweezers (thin one) as shown in the figure and remove the tab. Caution If you pick up the tab forcibly, the plate bends. It can be removed by just inserting the tweezers straightly. Fig.7 AVH-P5200BT/XNUC...
Page 95
Removing the BT PCB and BT ANT PCB (Fig.8) Straighten the tabs at two locations indicated and then remove the BT PCB. Disconnect the Cord Assy using GGF1539. Remove the screw and then remove the BT ANT PCB. BT PCB BT ANT PCB Fig.8 AVH-P5200BT/XNUC...
Page 96
Align the cushion to PCB silk-print, and stick it. Be careful not to touch the cushion to the USB terminal. The sticking direction is shown on the right figure. When you install the grille to the unit, confirm the cushion is sticking on the keyboard unit properly. AVH-P5200BT/XNUC...
Page 97
5. Take care not to catch the flexible part on the side face. 6. Take note that a deformation may be generated if you hold the front part of the upper frame or CRG mechanism part or a foreign object is inserted. Handling OK AVH-P5200BT/XNUC...
Page 98
Handling NG Fig. 1 Do not touch here Do not touch here Do not touch here : Do not touch here AVH-P5200BT/XNUC...
Page 99
(The flexible part is damaged if the board is removed without removing the flexible part, so be sure to remove it.) Fig. 1 Short circuit Connector (pickup flexible part) Fig. 2 1. Unscrew two screws and remove the CRG motor ASS'Y. CRG motor ASS’Y Locking screw (CRG) Locking screw (CRG) Fig. 3 AVH-P5200BT/XNUC...
Page 100
Be sure to carry out the actual applying of main shaft holddown spring. Retainer plate spring Main shaft PU unit Main shaft holddown spring Fig. 4 Sub shaft Temporary applying part of CRG chassis Temporary applying Actual applying AVH-P5200BT/XNUC...
Page 101
1. When you hold PU, hold “Handling OK” part shown in the figure and do not hold “Handling NG” part. Handling OK Handling NG Do not touch the radiator. Do not touch the ACT(object lens). Do not pull the FPC. Do not touch the Miller or Collimator lens. Fig. 5 AVH-P5200BT/XNUC...
• Once the EJECT key is pressed, do not press any other key until the disc is completely ejected. • Power OFF immediately in case of run a way. • Turning the volume for adjusting the laser power of the pickup unit may result in the breakage of the laser diode. AVH-P5200BT/XNUC...
Page 104
(method 1) and adjustment while checking the RF level values with the OSD (method 2). The adjustment procedure is shown below. For how to enter the test mode and the operation procedure, see the sections in the Service Test Mode. AVH-P5200BT/XNUC...
Page 105
(Perform adjustment in order of A => B => A, and finally rotate the screws clockwise to complete adjustment.) 11. Power OFF in the test mode, and check that the disc is stopped before ejecting. 12. Apply adhesive for fixing skew and screw lock. See the figure below for the spots to adhere. AVH-P5200BT/XNUC...
Page 106
D & E Sectional diagram of the spot to adhere in R-SKEW * Note: Make sure to cross-link both the resin and sheet-metal parts. Spots to apply adhesive * Note: Make sure to cross-link both the case and sheet-metal parts. AVH-P5200BT/XNUC...
Page 107
Precautions in handling pickup * Note: Avoid contact with the shaded part shown in the figure below. RF level adjustment part Avoid contact with optical components. Avoid contact with the spring. Hologram (beware of static electricity) GRT adjustment part AVH-P5200BT/XNUC...
Screw adjacent to mark on the product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions,apply as you think it appropriate.) 9.1 PACKING 5200BT/UC, 5250BT/RD 5250BT/RD 5250DVD/RC 5250DVD/RD 5250DVD/RI AVH-P5200BT/XNUC...
Page 113
See Contrast table (2) Protector CHP3992 15-5 Warranty Card See Contrast table (2) Protector CHP3993 (2) CONTRAST TABLE AVH-P5200BT/XNUC, AVH-P5250BT/XNRD, AVH-P5200DVD/XNUC, AVH-P5250DVD/XNRC, AVH-P5250DVD/ XNRD and AVH-P5250DVD/XNRI are constructed the same except for the following: Mark Description AVH-P5200BT/XNUC AVH-P5250BT/XNRD AVH-P5200DVD/XNUC Polyethylene Bag CEG1185...
Page 115
CND4325 Sheet CNN3421 Grille Assy See Contrast table (2) Screw BPZ20P060FTC (2) CONTRAST TABLE AVH-P5200BT/XNUC, AVH-P5250BT/XNRD, AVH-P5200DVD/XNUC, AVH-P5250DVD/XNRC, AVH-P5250DVD/ XNRD and AVH-P5250DVD/XNRI are constructed the same except for the following: Mark Description AVH-P5200BT/XNUC AVH-P5250BT/XNRD AVH-P5200DVD/XNUC Tuner Box Unit CWN3129 CWN3130...
Page 117
BPZ20P060FTC Screw(M2 x 2) CBA1872 CDE9146 Grille Assy See Contrast table (2) CDE9147 (2) CONTRAST TABLE AVH-P5200BT/XNUC, AVH-P5250BT/XNRD, AVH-P5200DVD/XNUC, AVH-P5250DVD/XNRC, AVH-P5250DVD/ XNRD and AVH-P5250DVD/XNRI are constructed the same except for the following: Mark Description AVH-P5200BT/XNUC AVH-P5250BT/XNRD AVH-P5200DVD/XNUC Monitor Unit CXX2841(Service)
Page 119
Monitor Unit(BT ANT PCB) See Contrast table (2) Insulator CNN3224 Heat Sink CNR1941 (2) CONTRAST TABLE AVH-P5200BT/XNUC, AVH-P5250BT/XNRD, AVH-P5200DVD/XNUC, AVH-P5250DVD/XNRC, AVH-P5250DVD/ XNRD and AVH-P5250DVD/XNRI are constructed the same except for the following: Mark Description AVH-P5200BT/XNUC AVH-P5250BT/XNRD AVH-P5200DVD/XNUC Cord Assy CDE9141...
TEMP1 GNDBL KEY BUS KEY1 SYSTEM UNIT PART TOUCH PANELPART POWER PART Q5801 VIDEO PART UMX1N FLASH ROM PART GERDA IC PART R5804 R5814 R5824 Q5802 LCD PANEL PART LSC4081UB BACKLIGHT PART (RED) (GREEN) (BLUE) KEY BOARD PART GNDILM AVH-P5200BT/XNUC...
Consists of FLASH ROM PART 5401 - MONITOR PCB GERDA IC PART 5501 - BT PCB LCD PANEL PART 5601 - BT ANT PCB BACKLIGHT PART 5701 - KEY BOARD PART 5801 - CHIP SIZE LEGEND 1608 2125 3216 3225 AVH-P5200BT/XNUC...
Page 170
BT_MIC1N TP8009 VCC_MIC TP8010 BT_MIC1P GNDBT GNDBT R8001 GNDBT R8004 BT model Only MONITOR UNIT(Service) Consists of MONITOR PCB BT PCB BT ANT PCB BT MODULE BT ANT PCB CN8601 CKS5749-A L8601 GNDANT CHIP SIZE LEGEND 1608 2125 3216 AVH-P5200BT/XNUC...
Page 195
11.9 BT ANT PCB BT ANT PCB SIDE A BT ANT PCB SIDE B C8602 BT MODULE L8601 CN8601 C8601 AVH-P5200BT/XNUC...
Page 196
IC104 C110 IC102 S101 C109 Angel sense R109 CN102 C105 Angel sw C103 R117 C107 C104 ANGLE MOTOR SLIDE MOTOR CN103 VOLUME PCB UNIT CN102 SIDE B VOLUME PCB UNIT MAIN PCB UNIT CN103 IC103 IC105 K L M AVH-P5200BT/XNUC...
Example) IC 301 is on the point (face A, 91 of x-axis, and 111 of y-axis) of the corresponding PC board. IC 301 (A, 91, 111) IC NJM2068V Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. H:AVH-P5200BT/XNUC I:AVH-P5250BT/XNRD B:AVH-P5200DVD/XNUC Unit Number : CXX2838(H) C:AVH-P5250DVD/XNRC Unit Number : CXX2839(I) D:AVH-P5250DVD/XNRD...
Page 198
(A,74,95) Chip Ferrite Bead DTL1107 D 123 (B,152,134) Diode HZU7L(C3) L 901 (B,70,67) Inductor CTF1473 D 124 (A,157,125) Diode DAN202U L 921 (B,95,88) Inductor CTF1473 D 125 (A,163,125) Diode DAN202U D 126 (A,146,122) Diode RKZ5.6KG(B2) L 922 (B,97,103) Inductor CTF1473 AVH-P5200BT/XNUC...
Page 199
R 132 (A,150,124) RS1/16SS104J R 314 (B,21,137) RS1/16SS102J R 133 (B,145,136) RS1/16SS472J R 315 (B,21,150) RS1/16SS102J R 134 (A,157,122) RS1/16SS103J R 332 (A,59,162) RS1/16SS471J R 135 (A,144,119) RS1/16SS103J R 333 (A,57,162) RS1/16SS471J R 136 (A,166,122) RS1/16SS153J R 334 (A,62,162) RS1/16SS102J AVH-P5200BT/XNUC...
Page 200
R 462 (B,53,133) RS1/16SS223J R 655 (A,129,75) RS1/16SS333J R 481 (B,60,168)(I,C,D,E) RS1/16SS0R0J R 660 (A,154,110) RS1/16SS473J R 482 (B,60,169)(I,C,D,E) RS1/16SS473J R 661 (B,154,85)(H,I) RS1/16SS473J R 483 (B,57,174)(I,C,D,E) RS1/16SS121J R 484 (B,62,172)(I,C,D,E) RS1/16SS104J R 665 (B,155,85) RS1/16SS473J R 667 (B,168,86)(H,B) RS1/16SS223J AVH-P5200BT/XNUC...
Page 201
R 785 (B,27,143)(H,B) RS1/16SS0R0J R 856 (A,74,62) RS1/16SS391J R 786 (A,24,141)(H,B) RS1/16SS0R0J R 866 (A,102,58) RS1/16SS103J R 787 (A,28,142)(H,B) RS1/16SS0R0J R 867 (B,92,68) RS1/16SS104J R 788 (A,40,142) RS1/16SS0R0J R 868 (A,70,68) RS1/16SS101J R 789 (A,41,142) RS1/16SS0R0J R 871 (A,66,94) RS1/16SS0R0J AVH-P5200BT/XNUC...
Page 202
R 981 (B,50,127) RS1/16SS102J R 2004 (B,13,123) RS1/16SS102J R 986 (B,45,127) RS1/16SS102J R 2005 (B,14,123) RS1/16SS102J R 987 (B,43,127) RS1/16SS105J R 2006 (B,12,123) RS1/16SS102J R 988 (B,41,127) RS1/16SS105J R 2007 (A,15,132) RS1/16SS102J R 990 (B,43,120) RS1/16SS103J R 2008 (A,16,132) RS1/16SS102J AVH-P5200BT/XNUC...
Page 203
CCSQCH223J50 C 405 (B,85,157) CKSRYB104K50 C 237 (B,110,122) CCSSCH100D50 C 413 (A,74,114) CKSSYB104K10 C 238 (B,126,124) CCSSCH100D50 C 415 (B,43,156) CKSSYB104K16 C 251 (B,73,125) CKSRYB105K10 C 416 (A,35,160) CKSSYB104K10 C 252 (B,70,125) CKSRYB105K10 C 441 (B,102,138) 4.7 uF CCG1201 AVH-P5200BT/XNUC...
Page 204
C 820 (A,90,97) CKSRYB105K10 C 1003 (B,158,135) CKSRYB103K50 C 821 (B,89,72) CKSSYB104K10 C 1004 (A,165,145) CEAT102M16(P30) C 822 (A,89,95) CKSSYB104K10 C 1005 (A,165,152) CKSRYB104K50 C 823 (B,91,72) CKSSYB104K10 C 1101 (A,35,163) CKSRYB104K50 C 824 (B,93,69) CKSSYB104K10 C 1102 (A,13,149) CEAT471M16 AVH-P5200BT/XNUC...
Page 205
C 1771 (B,45,54) CKSQYB225K10 (B,58,27) CKSRYB103K50 C 1772 (B,48,43) CKSRYB334K10 (B,59,25) CKSQYB475K10 C 1781 (B,118,59)(H,I) CKSSYB104K10 (B,66,21) CKSRYB103K50 (B,49,22) CKSRYB103K50 C 1782 (B,115,50)(H,I) CKSSYB104K10 C 2001 (A,20,137) CKSSYB104K10 C 10 (B,64,27) CKSRYB103K50 C 11 (B,69,31) CKSQYB475K10 C 12 (B,47,22) CKSRYB102K50 AVH-P5200BT/XNUC...
Page 206
Monitor Unit(Service) RESISTORS Consists of Monitor PCB R 3002 (B,130,10) RS1/16SS223J BT PCB R 3004 (B,125,6) RS1/16SS750J BT ANT PCB R 3005 (B,69,6) RS1/16SS103J R 3006 (B,130,6) RS1/16SS223J R 3007 (B,70,8) RS1/16SS151J R 3008 (B,70,7) RS1/16SS101J Unit Number : CXX2841(H,I) AVH-P5200BT/XNUC...
Page 207
(A,39,68) Inductor CTF1545 R 5503 (A,54,76) RS1/16SS0R0J L 5517 (A,38,62) Inductor CTF1545 R 5509 (A,77,45) RS1/16SS563J L 5518 (A,40,60) Inductor CTF1545 R 5511 (A,75,45) RAB4CQ102J L 5519 (A,41,51) Inductor CTF1545 R 5512 (A,79,54) RS1/16SS271J L 5520 (A,51,45) Inductor CTF1545 AVH-P5200BT/XNUC...
Page 208
CKSSYB104K10 R 5723 (A,10,20) RS1/10SR1203D C 5008 (A,114,16) 10 uF DCH1201 R 5724 (A,7,20) RS1/10SR0R0J C 5201 (A,124,64) CKSSYB103K16 R 5725 (A,11,27) RS1/16SS152J C 5202 (A,126,72) CKSRYB105K10 R 5726 (A,29,23) RS1/16SS103J C 5203 (A,133,62) CKSQYB106K6R3 R 5727 (A,27,23) RS1/16SS472J AVH-P5200BT/XNUC...
(A,89,43) L-MOS And Gate TC7SET08FUS1 C 5544 (A,44,65) CKSSYB104K10 C 5545 (A,38,64) CKSSYB103K16 IC 5401 (A,22,67) Flash ROM Unit CWW2644 C 5546 (A,51,77) CKSRYB105K10 IC 5501 (A,78,43) EEPROM IC S-93C66BD0I-I8 IC 5502 (A,57,59) IC MN103SH13UB C 5547 (A,40,61) CKSSYB104K10 AVH-P5200BT/XNUC...
Page 210
(A,80,65) RS1/16SS101J CN5601 (A,102,74) Connector CKS6062 R 5532 (A,41,48) RAB4CQ103J CN5701 (A,17,16) Connector CKS5561 CN5802 (A,109,11) Connector CKS5695 R 5533 (A,48,49) RS1/16SS103J R 5534 (A,82,55) RS1/16SS101J R 5536 (A,87,64) RS1/16SS101J RESISTORS R 5537 (A,86,65) RS1/16SS101J R 5539 (A,78,69) RS1/16SS101J AVH-P5200BT/XNUC...
Page 211
C 5511 (A,67,40) CKSSYB104K10 C 5512 (A,68,40) CKSSYB104K10 R 5823 (A,115,50) RS1/16SS121J C 5513 (A,62,45) CKSSYB104K10 R 5824 (A,116,51) RS1/16SS103J R 5833 (A,98,39) RS1/16SS391J C 5516 (A,64,42) CKSSYB104K10 R 5834 (A,103,47) RS1/16SS391J C 5517 (A,67,44) CKSSYB104K10 R 5835 (A,102,50) RS1/16SS391J AVH-P5200BT/XNUC...
Switch(Angle SW) CSN1068 C 5714 (A,8,43) 10 uF CCG1236 C 5715 (A,24,28) 10 uF CCG1236 C 5716 (A,11,25) CKSSYB104K10 C 5718 (A,8,30) CKSSYB104K10 Unit Number : C 5805 (A,93,37) CKSSYB104K10 Unit Name : Volume PCB Unit C 5806 (A,98,45) CKSSYB104K10 AVH-P5200BT/XNUC...
Page 213
R 1529 (A,77,20) RS1/16SS103J R 1200 (A,33,9) RS1/16SS753J R 1530 (B,54,28) RS1/16SS104J R 1201 (A,33,8) RS1/16SS753J R 1531 (A,67,41) RS1/16SS391J R 1205 (A,34,22) RS1/16SS1R0J R 1534 (A,74,39) RS1/16SS221J R 1210 (B,19,18) RS1/16SS101J R 1211 (A,19,13) RS1/16SS102J R 1535 (A,78,29) RS1/16SS101J AVH-P5200BT/XNUC...
Page 214
(B,68,57) 22 uF CCG1178 C 1605 (A,41,25) CCSSCH680J50 C 1201 (B,28,17) CKSYB475K16 C 1606 (A,40,29) CKSSYB104K10 C 1202 (B,28,20) CKSSYB104K16 C 1607 (A,50,38) CKSQYB106K6R3 C 1205 (A,33,23) CKSSYB103K16 C 1608 (A,47,33) CKSRYB105K10 C 1206 (A,36,23) CKSRYB104K16 C 1609 (A,54,40) CKSSYB104K10 AVH-P5200BT/XNUC...
Page 215
S 1202 Switch(8 cm) CSN1067 S 1203 Spring Switch(DISC SENS) CSN1069 S 1204 Spring Switch(DISC SENS) CSN1070 S 1205 Switch(8 cm) CSN1068 Unit Number : CWX3559 Unit Name : Compound Unit(B) MISCELLANEOUS S 1206 Switch(CLAMP) CSN1067 Miscellaneous Parts List AVH-P5200BT/XNUC...