Signal Connector Pin Assignment • DVI-I Connector (Digital/Analog) Signal (DVI-I) Signal (DVI-I) T. M. D. S. Data2- Hot Plug Detect T. M. D. S. Data0- T. M. D. S. Data2+ T. M. D. S. Data2/4 Shield T. M. D. S. Data0+ T.
PRECAUTION WARNING FOR THE SAFETY-RELATED COMPONENT. WARNING BE CAREFUL ELECTRIC SHOCK ! • There are some special components used in LCD monitor that are important for safety. These parts are • If you want to replace with the new backlight (CCFL) or marked on the schematic diagram and the inverter circuit, must disconnect the AC adapter...
SERVICING PRECAUTIONS CAUTION: Before servicing receivers covered by this 9. Use with this receiver only the test fixtures specified in service manual and its supplements and addenda, read this service manual. and follow the SAFETY PRECAUTIONS on page 3 of this CAUTION: Do not connect the test fixture ground strap publication.
Page 6
General Soldering Guidelines Replacement 1. Use a grounded-tip, low-wattage soldering iron and 1. Carefully insert the replacement IC in the circuit board. appropriate tip size and shape that will maintain tip 2. Carefully bend each IC lead against the circuit foil pad and solder it.
Page 7
Circuit Board Foil Repair At Other Connections Excessive heat applied to the copper foil of any printed Use the following technique to repair the defective copper circuit board will weaken the adhesive that bonds the foil pattern at connections other than IC Pins. This technique to the circuit board causing the foil to separate from or involves the installation of a jumper wire on the "lift-off"...
TIMING CHART VIDEO SYNC Total Total Front Sync Back Video Sync MODE H / V Frequency Period Period Porch Duration Porch Resolution Active Polarity Clock ( E ) ( E ) ( C ) ( D ) Time ( A ) ( F ) 28.35 31.500 KHz...
DISASSEMBLY Like the picture move. Remove the stand. Remove the screws. Remove the screws. Disassemble back cover. 1. Pull the front cover upward. 2. Then, let the all latches are separated. 3. Put the front face down. Remove the 4 screws from each side of metal Pull out the usb pcb.
DESCRIPTION OF BLOCK DIAGRAM 1. Video Controller Part & Display Data Transmitter Part.(MST9251A) This part amplifies the level of video signal for the digital conversion and converts from the analog video signal to the digital video signal using a pixel clock. The pixel clock for each mode is generated by the PLL.
LIPS Board Block Diagram 50 ~ 60Hz 100KHz HVDC ENERGY INPUT RECTIFIER OUTPUT RECTIFIER TRANSFER COMPONENTS AND FILTER AND FILTER LINE 100 ~ 240V SIGNAL PWM CONTROL COLLECT- PHOTO COUPLER CIRCUIT ISOLATION PRIMARY SECONDARY High Voltage output INVERTER CIRCUIT Operation description_LIPS 1.
ADJUSTMENT Windows EDID V1.0 User Manual 2. EDID Read & Write 1) Run WinEDID.exe Operating System: MS Windows 98, 2000, XP Port Setup: Windows 98 => Don’t need setup Windows 2000, XP => Need to Port Setup. This program is available to LCD Monitor only. 1.
SERVICE OSD 1) Turn off the power switch at the front side of the display. 2) Wait for about 5 seconds and press MENU, MINUS and POWER switch with 1 second interval. 3) The SVC OSD menu contains additional menus that the User OSD menu as described below. a) Exit b) ADC CAL.
TROUBLESHOOTING GUIDE 1. NO POWER NO POWER (POWER INDICATOR OFF) CHECK POWER BOARD, AND FIND OUT A SHORT CHECK J303 VOLTAGE POINT AS OPENING PIN5, PIN6 (5V)? EACH POWER LINE CHECK CHECK 5VS LINE U501 PIN 8 (OPEN CHECK) VOLTAGE (5V)? NO PROBLEM CHECK KEY CONTROL CONNECTOR ROUTINE...
Page 16
2. NO RASTER (OSD IS NOT DISPLAYED) – LIPS NO RASTER (OSD IS NOT DISPLAYED) J303 CHECK LIPS PIN5, 6 CHECK MICOM INV J303 PIN 9 ON/OFF PORT. 1. CONFIRM BRIGHTNESS OSD CONTRL STATE. J303 PIN 10 2. CHECK MICOM DIM-ADJ PORT CHECK PULSE AS...
Page 17
3. NO RASTER (OSD IS NOT DISPLAYED) - MAIN NO RASTER (OSD IS NOT DISPLAYED) U401 PIN102 (3.3V) CHECK U205 ~ U207 PIN102 (2.5V) 1. CHECK PIN 202, 203 U401 SOLDERING CONDITION PIN 202, 203 2. CHECK X401 14.318MHZ? 3. TROUBLE IN U201 U401 PIN18,36 IS 64KHz H-SYNC? CHECK CONNECTION LINE...
Page 18
4. TROUBLE IN DPM TROUBLE IN DPM CHECK U401 PIN 18,19,36,37 CHECK H/V SYNC LINE SYNC PULSE? TROUBLE IN U401 Waveforms 5 U401-#18,36 H-SYNC 5 U401-#19,37 V-SYNC - 18 -...
REPLACEMENT PARTS LIST CAUTION: BEFORE REPLACING ANY OF THESE COMPONENTS, READ CAREFULLY THE SAFETY PRECAUTIONS IN THIS MANUAL. * NOTE SAFETY Mark AL ALTERNATIVE PARTS DATE: 2006. 11. 20. DATE: 2006. 11. 20. *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION *S *AL LOC.