Page 2
Connection Terminals: VIDEO IN 1.0 Vp-p (75) AUDIO L-R RCA Pin jack x 2 0.5 Vrms HDMI1, HDMI2 Type A Connectors COMPONENT/RGB IN: with sync 1.0 Vp-p (75) 0.7 Vp-p (75) 0.7 Vp-p (75) AUDIO L-R RCA Pin jack x 2 0.5 Vrms DVI-D IN DVI-D 24 Pin x 2...
Safety Precautions General Guide Lines When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip"...
About lead free solder (PbF) Note: Lead is listed as (Pb) in the periodic table of elements. In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder. The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu). That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.
Applicable Input Signals PC signals *Mark:applicable input signal Horizontal Vertical HDMI1 RGB IN PC IN DVI-D IN Signal name frequency frequency HDMI2 (Dot clock (MHz) (Dot clock (MHz) (Dot clock (MHz) (kHz) (Hz) 640x400@70Hz 31.46 70.07 *(25.17) *(25.17) *(25.17) 640x400@85Hz 37.86 85.08 *(31.5)
Page 8
Component signals *Mark:applicable input signal Horizontal Vertical HDMI1 Component IN DVI_IN Signal name frequency frequency HDMI2 (Dot clock (MHz) (Dot clock (MHz) (kHz) (Hz) 525(480)/60i 15.73 59.94 *(13.5) *(27.0) 525(480)/60p 31.47 59.94 *(27.0) *(27.0) 625(575)/50i 15.63 50.00 *(13.5) 625(576)/50i 15.63 50.00 *(27.0) 625(575)/50p...
Service Hints How to remove the backcover Lay the main unit face down. (see Fig.5) Fig.5 Remove the 36 fixing screws. (see Fig.6) SCREWS (1) THEJ048J /34pcs/ (2) XTV3+10JFJK /2pcs/ Fig.6...
Chassis Board Layout V2-BOARD P-Unit DS-BOARD A-BOARD HX-BOARD V1-BOARD Board Name Function A-Board ST micro, YUV, Video IN, HDMI1/2, DVI-IN/OUT, PC, Speaker out DS-Board Slot Interface HX-Board RS-232C_IN/OUT, AUDIO IN V1-Board Remote Control Sensor, Power Indicator, Brightness Sensor V2-Board Power Switch, Key Switch P-Unit Power Supply Location of Lead Wiring...
Operating Instructions Press to display the Setup menu. Press to select „OSD LANGUAGE“. Press for more than 3 seconds. Press to select „OPTIONS“. Press to display the Options menu. Press to select your preferred menu. Press to adjust the menu. Press to exit from Option menu.
Option Menu LA29 chassis series have special function and operation setting facility called Option Menu. This Option Menu is useful for special function required customers. This should be set at the installation stage. Option menu Default setting Contents On screen display Enable/disable to display input mode indication after power on and no signal indication.
Service Mode CAT (Computer Aided Test) Mode CAT mode menu CAT panel sys. 8.2 Mode Function Access Button IIC Mode Service Alignment Action CD (Complete Software version Mute more than 3 CD Mode Diagnostic) information EEPROM edit seconds SD Mode SD (Status Display) MTBF parameter Action...
CD mode Select the CD mode by Up/Down button on the remote control at the front page of CAT mode and then press the Mute button on the remote control more than 3 seconds. MONITOR-MCU 1.0100S30 Factory use MONITOR-EEPROM 01.00 20 2152 New data MONITOR-EEPROM Change Addr...
MS Mode Select the MS mode by Up/Down button on the remote control at the front page of CAT mode and the press the Mute button on the remote control more than 3 seconds. Change by Left/Right buttons on the Market select 01.01 remote control and press the action button...
IIC mode structure (following items value is sample data) R DRIVE G DRIVE B DRIVE Panel W/B Adj. by VOL up/down button by up / down button by left / right button change of value R DRIVE G DRIVE B DRIVE LCD DRIVE Adj.
Self Check Self check is used to automatically check the bus line controlled circuit of the LCD display. To get into the Self check mode, press the volume down button on the customer controls at the top of the set, at the same time pressing the OFF TIMER button on the remote control, and the screen will show.
Power LED blinking timing chart Subject Information of LED Flashing timing chart. Contents When abnormality has occurred the unit, the protection circuit operates and reset to the stand by mode. At this time, the defective block can be identified by number of blinking of the Power LED on the front panel of the unit. PTCT Blinking times Name...
Adjustment Method RGB white balance adjustment Instrument Name Connect to Remarks INTERNAL PATTERN – 100% WHITE Picture menu: STANDARD Color analyzer User setting: Normal Panel surface except PICTURE: max 30 ( Minolta CA-210 or equivalent ) Procedure Remarks [Conditions] Internal signal: STANDARD ...
Wiring Diagram LCD PANEL MAIN IN P-UNIT SPK_L SPK_R VIDEO IN JK4006 V2-BOARD JK4005 HDMI2 V1-BOARD JK4004 HDMI1 A-BOARD DVI OUT JK4003 DVI IN JK4002 RS-232C JK3504 JK4001 HX-BOARD RS-232C JK3503 SERVICE JK3505 JK3501 AUDIO IN AUDIO IN SERVICE PC or DVI SERVICE SERVICE DS10...
Schematic Diagrams IMPORTANT SAFETY NOTICE Components identified by mark have special characteristics important for safety. When replacing any of these components, use only manufacturers' specified parts. NOTE RESISTOR All resistors are carbon ¼W resistor, unless marked otherwise. Unit of resistance is OHM () (k=1,000, M=1,000,000) CAPACITORS All capacitors are ceramic 50V unless marked otherwise.