Video cassette recorder nv-sv121 series (s-vhs, hi-fi); nv-hv61 series (hi-fi); nv-hv51 series (hi-fi); nv-mv21 series (mono) nv-mv16 series (mono) (32 pages)
Page 1
ORDER NO. MABR0303007C2 Video Cassette Recorder NV-SV120EG Z-MECHANISM SPECIFICATIONS 2003 Matsushita Electric Industrial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law. 1. INTRODUCTION 1.1. INTRODUCTION This service manual contains technical information which will allow service personnel to...
If the circuit is changed or modified, this information will be followed by supplementary service manual to be filed with original service manual. Note: Adjustment procedures, Disassembly Procedures and Assembly Procedures for Mechanism Chassis are separate volume from this service manual. / Please refer to the service manual for Z- Mechanism Chassis.
Page 3
PROCEDURE F.I.P. DISPLAY Turn on the Service Mode 1.Press the FF key and the EJECT key simultaneously for more than 3 seconds. Activate the Service Mode 2 2.While keep placing FF key, press the EJECT key in twice. Activate the Entering Mode. 3.Press the EJECT key for more than 3 seconds.
Model No. NV-SV120EG Fig. S2 Model Code & Option Code NOTE: Since all electrical adjustments data is still not available, perform the Electrical Adjustment continuously. 2.1.2. CYLINDER UNIT REPLACEMENT 1. CYLINDER UNIT REPLACEMENT A. Remove the mechanism unit from MAIN C.B.A./Chassis by referring “SECTION 2.
Page 5
E. Loose Hex screw (C) (1.5 mm) and remove the CYLINDER RETAINER. F. Remove the Upper Cylinder. Fig. S4 3. UPPER CYLINDER ASSEMBLY When reassembling, perform the steps in the reverse order. Notes: 1. Install the Cylinder Retainer so that the 2 holes on top of the Cylinder Retainer are at right angles with the P5001 Connection.
Page 6
2. Tighten the Hex screw (C) (1.5 mm) while pressing down on top of the Cylinder Retainer. Fig. S5 3. Install the Cylinder Rotor Unit so that the inner hole of the Cylinder Rotor Unit fits to the small projection (D) on top of the Upper Cylinder.
7. Confirm the PG SHIFTER ADJUSTMENT with the alignment tape (PAL: VFJ8125H3F) and adjust it if necessary. 2.1.3. CHECKING OF MAIN C.B.A. When servicing the MAIN C.B.A., take out the MAIN C.B.A. and mechanism from the frame and turn over. Fig.
Page 8
Fig. S11 D. Rotate the Main Cam Gear clockwise until the cassette tape is ejected. 2.3. INTRODUCTION OF VIDEO HEAD CLEANING CASSETTE / (POLISHING TYPE ) 1. We are pleased to introduce Panasonic Video Head Cleaning...
Page 9
Cassette, VFK0923FT [for service purposes] and VFK0923FSE [ for end users] for all VHS/SVHS VCP and VCR. 2. These cleaning cassettes are exclusive removing the hard and sticky clogging on video heads. 3. These improve the efficiency of video head cleaning service and shortening cleaning time for end users.
VFK0823FSE (For end users) Type of Cassette Full VHS Cassette Cleaning Time 10 Seconds/Time Tape Length 3.34 m Usability in a Path 30 Times Note: The tape material itself is the same in both types. 2.4. SELF-DIAGNOSIS RESULT DISPLAY The "SELF-DIAGNOSIS RESULT DISPLAY & MEMORY function is built in this VTR. It means that when the VCR detects undesirable condition, it can be displayed a “Error code (Two numbers from the right)”...
INDICATION CAUSE REMEDY/CHECK After cylinder lock is detected, the cylinder Check the cylinder motor drive circuit. does not start rotating again even after tape unloading. Cassette tape is not wound up during the tape Check the capstan motor drive circuit. unloading except EJECT mode.
3.1.2. DETAIL OF DISASSEMBLY METHOD 1. REMOVAL OF THE TOP PANEL Remove 4 Screws (A) Fig.D2 2. REMOVAL OF THE FRONT PANEL UNIT Unlock 7 Tabs (B) Fig. D3...
3. REMOVAL OF THE MECHANISM UNIT Remove Screw (C) Remove 3 Screws (D) Remove 2 Screws (E) Note: 1. Keep pressing 2 stoppers on Cassette Holder Plate and Press Cassette Holder Plate to the rear. 2. Remove the Mechanism Unit after bend the Cylinder Shield in the direction of the arrow.
Remove 4 Screws (F) Unlock 4 Tabs (G) Fig. D5 NOTE: Before mounting the MAIN C.B.A. onto the frame, be sure to confirm that the insulation sheet is mounted on the frame as shown in Fig. D6 Fig. D6 5. SERVICING POSITION Fig.
3.2. MECHANICAL ADJUSTMENT PROCEDURES Refer to the Service Manual for Z-Mechanism Chassis. / (Order No. VRD9802005C2) 3.3. ELECTRICAL ADJUSTMENT PROCEDURES 3.3.1. TEST EQUIPMENT The following equipments are required for Electrical Adjustments. 1. Dual-Trace Oscilloscope - Voltage Range: 0.005-5V/div - Frequency Range: DC-35MHz - Probes: 10:1 / 1:1 2.
When no indication in the procedure, set each selector as follows. 1. TAPE SPEED: SP 2. CHANNEL: AV1/AV2/AV3 (Set to signal input terminal number) 3. S-VHS SW: ON 3.3.3. ADJUSTMENTS Fig.E1 Fig.E2 Fig.E3 CONDITION: BURST SIGNAL OFF / CONDITION: BURST SIGNAL 75ohm TERMINATED 75ohm TERMINATED Fig.E4...
Page 17
PROCEDURES FIP DISPLAY Press the FF and EJECT Keys simultaneously for 3 seconds. Press the FF and EJECT Keys simultaneously twice. Press the EJECT key for 3 seconds. Press the CH UP key once. Insert the Alignment cassette tape. (PAL:VFJ8125H3F) When the sequence of the automatical adjustment has been terminated, the following action has been made.
Page 18
PROCEDURES FIP DISPLAY Set the 3D DNR SW to ON, and the S-VHS REC to ON in OSD menu fuction. / Insert the S-VHS BLANK TAPE. / Input the Video sweep signal (See Fig. E1) to AV3 (S-VIDEO IN) and record it in SP and LP.
PROCEDURES FIP DISPLAY Set the S-VHS ET REC to OFF in OSD menu function, but the 3D DNR SW to ON. / Insert the VHS Blank Tape. / Input the Video sweep signal (See Fig. E3) to AV1 (VIDEO IN) and record it in SP and LP.
11. REPLACEMENT PARTS LIST 11.1. CHASSIS PARTS SECTION PARTS LIST - All parts except parts mentioned [AVC-SPC] in the Remarks column are supplied from MAVD. Parts mentioned [AVC-SPC] are supplied from PAVC-CSG (AVC- SPC).
Page 26
Ref. No. Part No. Part Name & Description Remarks VEG1600 CYLINDER UNIT VXP2173 UPPER CYLINDER UNIT VDB1256 CYLINDER RETAINER VEM0715 CYLINDER MOTOR UNIT VXS0135 EARTH BRUSH UNIT VMD3795 FLAT CABLE HOLDER VEK9069 CAPSTAN UNIT L1AZ00000004 FE HEAD VDB1431 TENSION ARM BOSS VDB1460 SUPPLY BRAKE ARM BOSS VDG1220KIT...
Ref. No. Part No. Part Name & Description Remarks VMD3379 SIDE PLATE (L) VXA6540 SIDE PLATE (R) UNIT VXA5746 CASSETTE HOLDER UNIT VXP1730 MAIN SHAFT UNIT VHD1117 SCREW VHD1117 SCREW VHD0842 SCREW VHD0843 SCREW VHD0843 SCREW VHD0844 SCREW VHD0844 SCREW VHD1066 SCREW VHD1066...
Ref. No. Part No. Part Name & Description Remarks VGM1990 TOP PANEL silver NV-SV120EG-S VGM1993 TOP PANEL black NV-SV120EG-K VYP8735 FRONT PANEL U SV120 NV-SV120EG-K VYP8695 FRONT PANEL U SV120 NV-SV120EG-S RKA0072-K FOOT RKA0072-K FOOT VYF2888 DOOR UNIT NV-SV120EG-S VYF2896...
RF CABLE EG/EGC RJA0043-1C POWERCORD(MINI/E+EG) VPK2246 ACCESSORIES PACKING VPN5555 CUSHION (L) VPN5554 CUSHION (R) VPG0S72 PACK.CASE SV120 K NV-SV120EG-K VPG0S68 PACK.CASE SV120 S NV-SV120EG-S SERVICE FIXTURES & TOOLS VFJ8125H3F VHS ALIGNMENT TAPE (PAL) [AVC-SPC] VFK0335 RETAINING RING REMOVER (3mm/ [AVC-SPC]...
Page 30
Ref. No. Part No. Part Name & Description Remarks VEP06F09A MAIN C.B.A. (RTL) THE FOLLOWING C.B.A. IS INCLUDED IN MAIN C.B.A. VEP07A23S-SK VEP07A23S-SK TV DEMODULATOR PACK C.B.A. (RTL) INCLUDED IN MAIN C.B.A.(VEP06F09A). VEP03G25A S-VHS PACK C.B.A. (RTL) VEP04832A FRONT C.B.A. (RTL) ------------ CYLINDER STATOR C.B.A.
Page 31
Ref. No. Part No. Part Name & Description Remarks C1027 F1H1C104A071 CHIP CAPACITOR C1028 EEUEB1E470SB ALU ELEC CAPACITOR C1120 VCF2AAF683M EMI CAPACITOR ECQU2A683MVA C1121 F1BAF1020020 CAPACITOR C1123 F1BAF1020020 CAPACITOR C1141 EEUEB2G330E ALU ELEC CAPACITOR C1151 ECQB1H473JF3 PLAST FILM CAPACITOR C1152 ECQB1H103JF3 PLAST FILM CAPACITOR C1153...
Page 32
Ref. No. Part No. Part Name & Description Remarks C3013 F1H1C104A071 CHIP CAPACITOR C3014 F1H1C104A071 CHIP CAPACITOR C3015 F1H0J105A002 CHIP CAPACITOR C3016 F1H1C104A071 CHIP CAPACITOR C3017 F1H1C104A071 CHIP CAPACITOR C3019 F1H1C104A071 CHIP CAPACITOR C3020 ECEA1HKA3R3B ALU ELEC CAPACITOR C3021 ECEA1CKA100B ALU ELEC CAPACITOR C3023 F1H1H103A748...
Page 33
Ref. No. Part No. Part Name & Description Remarks C4017 ECEA1CKA100B ALU ELEC CAPACITOR C4018 ECEA1HKA010B ALU ELEC CAPACITOR C4019 ECEA1CKA100B ALU ELEC CAPACITOR C4020 F1H1H221A736 CHIP CAPACITOR C4021 ECQB1H223JF3 PLAST FILM CAPACITOR C4022 F1H1H152A219 CHIP CAPACITOR C4023 ECEA1AKA470B ALU ELEC CAPACITOR C4024 F1H1E223A029 CHIP CAPACITOR...
12. SCHEMATIC DIAGRAM FOR PRINTING WITH A4 SIZE...
Page 55
THE STRIPED FRAME INDICATES THE PRIMARY CIRCUIT TO DISTINGUISH THE PRIMARY CAUTION FROM THE SECONDARY CIRCUIT. PAY ATTENTION NOT TO RECEIVE AN ELECTRIC SHOCK DURING REPAIR AND SERVICE OF THE PRODUCTS. R :TO POWER SUPPLY/RF SECTION S :TO SYSTEM CONTROL & SERVO SECTION T :TO TIMER SECTION T1150 ETS29AZ286AC...
Page 56
VIDEO MAIN SIGNAL PATH IN REC MODE AUDIO MAIN SIGNAL PATH IN REC MODE P :TO POWER TRANSFORMER SECTION :TO SYSTEM CONTROL & SERVO SECTION VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE AUDIO MAIN SIGNAL PATH IN PLAYBACK MODE V :TO LUMINANCE & CHROMINANCE/AUDEIO SECTION TUNER UNIT Q1013 Q1003...
Page 57
VIDEO MAIN SIGNAL PATH IN REC MODE VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE PS3301 V MASK SYS IIC DATA SYS IIC CLOCK (EB) R3315 PS 3.3V L3301 C IN DNR 5V PB C C3383 C3355 R3313 R3314 C3344 R3316 C3341 C3339 C3340...
Page 63
R :TO POWER SUPPLY/RF SECTION VIDEO MAIN SIGNAL PATH IN REC MODE :TO SYSTEM CONTROL & SERVO SECTION VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE :TO Hi-Fi AUDIO SECTION AUDIO MAIN SIGNAL PATH IN REC MODE :TO INPUT/OUTPUT SECTION D :TO DECODER SECTION AUDIO MAIN SIGNAL PATH IN PLAYBACK MODE C3042 Q3001...
(VEM0715) CYLINDER STATOR UNIT Integrated Circuit HALL IC Connector M1 VM P2901 ADDRESS INFORMATION HALL IC VM M2 P2901 NV-SV120EB/EC/EP CYLINDER STATOR UNIT...
Page 66
FRONT C.B.A. Integrated Circuit IC4801 Connector PS4801 ADDRESS INFORMATION (VEP04832A) NV-SV120EB/EC/EP FRONT C.B.A.
Page 68
IMPORTANT SAFETY NOTICE: COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS, USE ONLY THE SAME TYPE. THE STRIPED FRAME INDICATES THE PRIMARY CIRCUIT TO DISTINGUISH THE PRIMARY CAUTION FROM THE SECONDARY CIRCUIT. PAY ATTENTION NOT TO RECEIVE AN ELECTRIC SHOCK DURING REPAIR AND SERVICE OF THE PRODUCTS.
Page 71
Pin No. Signal Name P-OFF P-SAVE P-FAIL Reset Describe A.DEF(H) O Output signal for audio defea and decoder IC reset. Detection of COLOR KILLER active. CKILLER DET(L) AFC S S curve input from tuner. Output signal depens on tape speed. SLP(H) (During N10H or P9H: High) (Except N10H and P9H: Low)
Page 72
Pin No. Signal Name P-OFF P-SAVE P-FAIL Reset Describe Input terminal for mechanism position. POS.SW3 D.A.REC(H) POS.SW2 BIAS(L) 140mS 140mS POS.SW1 RESET(L) MICOM reset input terminal. 32KHz IN Sub oscillator input. 32KHz OUT O Sub oscillator output. +5V(D) Power. 12MHz.IN Main oscillator input.
Page 73
Pin No. Signal Name P-OFF P-SAVE P-FAIL Reset Describe HALF_WAVE(H) O Control signal for switching capstan motor mode FAST and SLOW. CAP.ET O Torque control signal for capstan motor. CYL.ET O Torque control signal for cylinder motor. 4.213V 4.213V 4.213V P FAIL Interrupt input signal for power fail detection.
Page 85
Mute signals INPUT CONDITION Audio Output Results IC4501 settings POWER INPUT RF (C) AV1 Out AV2 Out REC/ Input Mute A-Mute SELECT VV ON(H) PB(H) Selector Selector Select Select P.ON INSEL OUTSEL AV1IN AV1IN AV1IN AV1IN INSEL EXT1 OUTSEL AV2IN AV2IN AV2IN AV2IN...
Page 86
SYSTEM CONTROL & SERVO ICs DC VOLTAGE CHART (SP MODE) Ref. No. IC1501 IC1502 MODE STOP PLAY IC2501 Ref. No. MODE STOP 15.4 15.4 15.6 -0.1 15.4 PLAY 15.0 15.0 15.2 15.0 15.1 15.0 15.3 -0.1 15.0 14.7 14.6 14.9 15.0 14.6 14.6...
Page 87
SYSTEM CONTROL & SERVO TRs DC VOLTAGE CHART (SP MODE) Q1501 Q1502 Q6004 Q6008 Q6009 Ref. No. (−) (−) MODE STOP -0.1 -0.1 12.4 PLAY -0.1 11.8 12.4 12.3 -0.1 -0.1 12.4 -0.1 -0.1 12.4 -0.1 -0.1 12.4 Q6010 QR6001 QR6004 Ref.
Page 88
4.43 NTSC L BILINGUAL 443NT [L] BILINGUAL L A. COMP BIL [L] AUDIO COMPONENT SIGNAL BILINGUAL H BIL. [H] A. COMPO AUDIO COMPONENT SIGNAL BILINGUAL L AUDIO DUBBING PAUSE L BIL/M1 [L] A. D.P [L] AUDIO DUBBING PAUSE L BS CLOCK A.
Page 89
CYL GND CYLINDER GND FULL. E. 12V FULL ERASE 12V DELAIED FM RECORDING H D.F.M. REC [H] GND (ANALOG) GND [A] DELAIED FM RECORDING L D. FM REC [L] GND (TUNER) GND [TU] D. GND GND/NON SW 12V DIGITAL GND GND/N.
Page 90
POWER OFF H LINE IN [R] LINE INPUT (R) P-OFF [H] POWER OFF L LINE OUT [L] LINE OUTPUT (L) P-OFF [L] LINE OUT [R] LINE OUTPUT (R) P. FAIL POWER FAILURE DETECT LP H POWER OFF H LP [H] P.
Page 91
SYSTEM CONTROL 5V RF OUT RF OUTPUT SYSCON 5V SYSTEM SW RF Y RF LUMINANCE SIGNAL SYSTEM TAKE-UP PHOTO TRANSISTOR RF. Y. IN RF LUMINANCE SIGNAL INPUT T-PHOTO TAKE-UP REEL PULSE RF. Y. OUT RF LUMINANCE SIGNAL OUTPUT T-RL. PLS TIMER BUS CLOCK ROTAR.
Page 92
If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local Panasonic Dealer. IF THE FITTED MOULDED PLUG IS UNSUITABLE TYPE B FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY.
8 SCHEMATIC DIAGRAMS 8.1. POWER TRANSFORMER SECTION IN MAIN SCHEMATIC DIAGRAM THE STRIPED FRAME INDICATES THE PRIMARY CIRCUIT TO DISTINGUISH THE PRIMARY CAUTION FROM THE SECONDARY CIRCUIT. PAY ATTENTION NOT TO RECEIVE AN ELECTRIC SHOCK DURING REPAIR AND SERVICE OF THE PRODUCTS.
Page 94
CE OF R :TO POWER SUPPLY/RF SECTION S :TO SYSTEM CONTROL & SERVO SECTION T :TO TIMER SECTION T1150 ETS29AZ286AC HEATER DC(-) C1280 10V100 D1280 11EQS04 HEATER DC(+) D1270 MA185 UNREG -29V C1270 50V22 D1250 L1250 ERA85-009V5 UNREG 14V C1250 C1251 R1200 R1207...
8.2. POWER SUPPLY/ RF SECTION IN MAIN SCHEMATIC DIAGRAM VIDEO MAIN SIGNAL PATH IN REC MODE AUDIO MAIN SIGNAL PATH IN P :TO POWER TRANSFORMER SECTION :TO SYSTEM CONTROL & SERVO SECTION VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE AUDIO MAIN SIGNAL PATH IN V :TO LUMINANCE &...
IN SIGNAL PATH IN REC MODE IN SIGNAL PATH IN PLAYBACK MODE TUNER UNIT Q1003 TU7601 2SB710A ENG47328G1:EB OWER SAVE CONTROL) ENG47327G1:EC 37.1 37.1 ENG47329G1:EP L7601 36.4 N.SW 5V R7603 R1016 C7603 C7605 6V100 0.01 AUDIO OUT R7606 DATA L7602 PS 5V R7605 C7604...
8.3. TIMER SECTION IN MAIN SCHEMATIC DIAGRAM P :TO POWER TRANSFORMER SECTION DP7501 A2BA00000212 R :TO POWER SUPPLY/RF SECTION S :TO SYSTEM CONTROL & SERVO SECTION :TO INPUT/OUTPUT SECTION S-VHS P10 P11 P12 P13 P14 P15 P16 R7507 HEATER (+) C7501 0.01 HEATER DC (-)
Page 102
IO IIC CLOCK IO IIC DATA SYS IIC DATA SYS IIC CLOCK TL2503 P2501 CAP TL CAP EC CAP R/F CAP FG1 GND (FG) REG 5V GND (MOTOR) LOAD MOTOR (-) LOAD MOTOR (+) UNREG 14V UNLOADING H LOADING H TL2502 POWER(NPN Tr.X3) CHARGE...
Page 103
8.5. LUMINANCE & CHROMINANCE/ AUDIO SECTION IN MAIN SCHEMATIC DIAGRA R :TO POWER SUPPLY/RF SECTION VIDEO MAIN SIGNAL PATH IN REC MODE :TO SYSTEM CONTROL & SERVO SECTION VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE :TO Hi-Fi AUDIO SECTION AUDIO MAIN SIGNAL PATH IN REC MODE :TO INPUT/OUTPUT SECTION D :TO DECODER SECTION AUDIO MAIN SIGNAL PATH IN PLAYBACK MODE...
Page 104
C DIAGRAM C3042 Q3001 R3009 R3010 C3028 R3011 2SD601A TW3001 50V4.7 (AMP) R3015 3300 R3017 INVERT C3027 50V1 CR DET TANK COME MESECAM C5007 COLOR LEVEL (3.3) DETECTOR Q7QF024P L5001 ENVDET C5005 C5006 6V47 C5004 LB5004 0.01 (4.6) R4017 3300 Q4005 (-0.8) 2SD602A...
Page 107
8.6. Hi-Fi AUDIO SECTION IN MAIN SCHEMATIC DIAGRAM :TO POWER SUPPLY/RF SECTION AUDIO MAIN SIGNAL PATH IN REC MODE AUDIO MAIN SIGNAL PATH IN PLAYBAC :TO SYSTEM CONTROL & SERVO SECTION :TO LUMINANCE & CHROMINANCE/AUDIO SECTION :TO INPUT/OUTPUT SECTION L4502 :TO DECODER SECTION 1.2u C4525...
8.7. INPUT/ OUTPUT SECTION IN MAIN SCHEMATIC DIAGRAM :TO POWER SUPPLY/RF SECTION VIDEO MAIN SIGNAL PATH IN REC MODE VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE :TO SYSTEM CONTROL & SERVO SECTION :TO LUMINANCE & CHROMINANCE/AUDIO SECTION :TO Hi-Fi AUDIO SECTION R4901 C4903 T :TO TIMER SECTION...
Page 110
MODE AUDIO MAIN SIGNAL PATH IN REC MODE AUDIO MAIN SIGNAL PATH IN PLAYBACK MODE JK4903 TW3021 TW3024 K2HZ105B0007 R4936 R4932 C4956 0.01 R4901 C4903 S-VIDEO R4937 R4933 IC4901 C1AB00000601 JK4904 K2HA304B0005 LB4909 VLP0147 R4902 AUDIO OUT (R) C4952 C4953 470P LB4910 C4902...
Page 111
8.8. DECODER SECTION IN MAIN SCHEMATIC DIAGRAM R :TO POWER SUPPLY/RF SECTION S :TO SYSTEM CONTROL & SERVO SECTION V :TO LUMINANCE & CHROMINANCE/AUDIO SECTION A :TO Hi-Fi AUDIO SECTION C7628 IC7601 C0EAH0000051 (RESET) SIF2 R7623 C7624 INPUT SWITCH VREF1 AGC, L7607 R7615...
Page 115
8.10. S-VHS PACK SCHEMATIC DIAGRAM VIDEO MAIN SIGNAL PATH IN REC MODE VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE PS3301 V MASK SYS IIC DATA SYS IIC CLOCK (EB) PS 3.3V L3301 C IN DNR 5V PB C C3383 C3355 R3313 R3314 0.01:EB...
8.11. FRONT SCHEMATIC DIAGRAM VIDEO MAIN SIGNAL PATH IN REC MODE AUDIO MAIN SIGNAL PATH IN REC MODE IC4801 PNA4618M10V JK4801 (IR RECEIVER) K2HA307A0003 S-VIDEO AUDIO AUDIO VIDEO IN (R/N) IN (L) JK4802 VJJ0574 C4805 C4806 L4802 L4801 R4801 BOTTOM PLATE R4803 R4802...
8.12. CYLINDER STATOR UNIT SCHEMATIC DIAGRAM CYLINDER SERVO SPEED LOOP P2901 MAIN COIL 2 P2502-9 MAIN COIL 3 P2502-8 P2502-7 P2502-6 HALL IC GND (CYL) P2502-5 P2502-4 P2502-3 MAIN COIL 1 P2502-2 P2502-1 NV-SV120EB/EC/EP CYLINDER STATOR NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR SCHEMATIC DIAGRAM ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST.
Page 122
C/EP AGRAM R0212 R0213 Q0203 Q0202 IC0201 (CAPSTAN MOTOR DRIVE) RCC SET Q0201 R0210 D0203 TL0204 TL0202 TL0203 TL0201 L0201 C0208 R0204 C0210 C0209 ED/S TORQUE DIRECTION OUT2 CAPSTAN MOTOR DRIVER MAIN COIL HALL POWER OUT1 EC AMP TL0205 DRIVER CONTROL LOGIC C0207...
Page 123
MAIN SIGNAL PATH IN REC MODE MAIN SIGNAL PATH IN PLAYBACK MODE IC4501 JK4801 (AV3) FRONT PS4801 PP3901 AUDIO IN (R) AUDIO PS4801 PP3901 MAIN IIC CLOCK TO/FROM IN (L) IIC BUS SYSTEM INTERFACE CONTROL MAIN IIC DATA JK4902 (AV1) TW4504 QR4504 AUDIO OUT (R)
Page 128
MAIN SIGNAL PATH IN REC MODE MAIN SIGNAL PATH IN PLAYBACK MODE IC4501 JK4801 (AV3) FRONT PS4801 PP3901 AUDIO IN (R) AUDIO PS4801 PP3901 MAIN IIC CLOCK TO/FROM IN (L) IIC BUS SYSTEM INTERFACE CONTROL MAIN IIC DATA JK4902 (AV1) TW4504 QR4504 AUDIO OUT (R)
Page 129
IC3305 :VIDEO MAIN SIGNAL PATH IN REC MODE (SUB EMPHASIS,YC SEP/DNR INTERFACE,OSD YC SEP) :VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE SUB EMPHASIS SVHS PP3001 PS3301 EMPHA OUT TO/FROM LUMINANCE & CHROMINANCE PP3001 PS3301 EMPHA IN LAG-LEAD FILTER REC VHS SYNC SYNC for VIDEO PROCESS...
Page 130
IC6001 IC7501 IC0201 (CAPSTAN MOTOR DRIVE) (SYSTEM CONTROL/SERVO IC) DP7501 CAPSTAN TL2503 MOTOR TL0201 IC7501 IC4801 P0201 P2501 MOTOR DIFFERENTIAL TORQUE CURRENT DRIVE AMPRIFIER CONTROL LIMIT N.SW N.SW P.FAIL L RESET TIMER DISPLAY RECEIVER HALF WAVE TL AMP PP3901 PS4801 CAPSTAN P0201 P2501...
VIDEO MAIN SIGNAL PATH IN REC MODE VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE (EC/EP) IC4902 (INPUT/OUTPUT SELECT) L3016, L3015, C3063 C3069 JK4903 1.7MHz 4.47MHz TW3024 TW3021 SECAM YC S-VIDEO DATA TRAP IIC BUS IC3002 CLOCK INTERFACE CHROMA SEPARATOR REAR C OUT REAR Y OUT SECAM C Q3006...
Page 132
IC3001 (AUDIO/VIDEO SIGNAL PROCESSOR) FIXED TO INT IN THES MODELS BY PP3001 PS3301 C IN PIN53 PP3002 PS3302 2MHz VIDEO OUT PP3002 PS3302 OSD VIDEO SVHS SQUELCH PP3002 PS3302 C OUT -6dB -4dB PP3002 PS3302 Y OUT SVHS CLEAR PP3002 PS3302 SQUELCH V-AMP...
Page 133
R0206 (FG HEAD) R0212 R0213 Q0203 P0201 Q0202 IC0201 R0207 CAP TL (CAPSTAN MOTOR DRIVE) HOLE HOLE CAP EC SENSOR SENSOR CAP R/F RCC SET CAP FG1 GND (FG) R0210 Q0201 C0201 REG 5V GND (MOTOR) D0203 TL0204 TL0202 TL0203 LOAD MOTOR (-) LOAD MOTOR (+) TL0201...
Page 134
CYLINDER SERVO SPEED LOOP P2901 MAIN COIL 2 P2502-9 MAIN COIL 3 P2502-8 P2502-7 P2502-6 HALL IC GND (CYL) P2502-5 P2502-4 P2502-3 MAIN COIL 1 P2502-2 P2502-1 NV-SV120EB/EC/EP CYLINDER STATOR NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR SCHEMATIC DIAGRAM ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST.
Page 135
R :TO POWER SUPPLY/RF SECTION AUDIO SIGNAL PATH S :TO SYSTEM CONTROL & SERVO SECTION V :TO LUMINANCE & CHROMINANCE/AUDIO SECTION A :TO Hi-Fi AUDIO SECTION X7601 H0D245500011 C7630 C7631 R7626 C7628 8200 IC7601 C0EAH0000051 (RESET) SIF2 C7624 R7623 NICAM INPUT DEMODULATION NICAM...
Page 136
:TO POWER SUPPLY/RF SECTION AUDIO MAIN SIGNAL PATH IN REC MODE AUDIO MAIN SIGNAL PATH IN PLAYBACK MODE :TO SYSTEM CONTROL & SERVO SECTION :TO LUMINANCE & CHROMINANCE/AUDIO SECTION :TO INPUT/OUTPUT SECTION L4502 R4521 :TO DECODER SECTION 1.2u 4700 C4525 C6526 R4522 C4524...
Page 137
VIDEO MAIN SIGNAL PATH IN REC MODE AUDIO MAIN SIGNAL PATH IN REC MODE IC4801 PNA4618M10V JK4801 (IR RECEIVER) K2HA307A0003 S-VIDEO AUDIO AUDIO VIDEO IN (R/N) IN (L) JK4802 VJJ0574 C4805 C4806 L4802 L4801 R4801 BOTTOM PLATE R4803 R4802 C4804 C4803 1000P 1000P...
Page 138
:TO POWER SUPPLY/RF SECTION VIDEO MAIN SIGNAL PATH IN REC MODE VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE AUDIO MAIN SIGNAL PATH IN REC MODE AUDIO MAIN SIGNAL PATH IN PLAYBACK MODE :TO SYSTEM CONTROL & SERVO SECTION JK4903 :TO LUMINANCE & CHROMINANCE/AUDIO SECTION TW3021 TW3024 K2HZ105B0007...