Video cassette recorder nv-sv121 series (s-vhs, hi-fi); nv-hv61 series (hi-fi); nv-hv51 series (hi-fi); nv-mv21 series (mono) nv-mv16 series (mono) (32 pages)
Page 1
ORDER NO. MABR0304008C2 Video Cassette Recorder NV-SV120EF Z-MECHANISM SPECIFICATIONS 1. INTRODUCTION 1.1. INTRODUCTION This service manual contains technical information which will allow service personnel to...
Page 2
understand and service this model. If the circuit is changed or modified, this information will be followed by supplementary service manual to be filed with original service manual. Note: Adjustment procedures, Disassembly Procedures and Assembly Procedures for Mechanism Chassis are separate volume from this service manual. / Please refer to the service manual for Z- Mechanism Chassis.
Page 3
PROCEDURE F.I.P. DISPLAY Turn on the Service Mode 1.Press the FF key and the EJECT key simultaneously for more than 3 seconds. Activate the Service Mode 2 2.While keep placing FF key, press the EJECT key in twice. Activate the Entering Mode. 3.Press the EJECT key for more than 3 seconds.
Page 4
Model No. NV-SV120EF Fig. S2 Model Code & Option Code NOTE: Since all electrical adjustments data is still not available, perform the Electrical Adjustment continuously. 2.1.2. CYLINDER UNIT REPLACEMENT 1. CYLINDER UNIT REPLACEMENT A. Remove the mechanism unit from MAIN C.B.A./Chassis by referring “SECTION 2.
Page 5
E. Loose Hex screw (C) (1.5 mm) and remove the CYLINDER RETAINER. F. Remove the Upper Cylinder. Fig. S4 3. UPPER CYLINDER ASSEMBLY When reassembling, perform the steps in the reverse order. Notes: 1. Install the Cylinder Retainer so that the 2 holes on top of the Cylinder Retainer are at right angles with the P5001 Connection.
Page 6
2. Tighten the Hex screw (C) (1.5 mm) while pressing down on top of the Cylinder Retainer. Fig. S5 3. Install the Cylinder Rotor Unit so that the inner hole of the Cylinder Rotor Unit fits to the small projection (D) on top of the Upper Cylinder.
Page 7
7. Confirm the PG SHIFTER ADJUSTMENT with the alignment tape (PAL: VFJ8125H3F) and adjust it if necessary. 2.1.3. CHECKING OF MAIN C.B.A. When servicing the MAIN C.B.A., take out the MAIN C.B.A. and mechanism from the frame and turn over. Fig.
Page 8
C. Rotate the Capstan Motor clockwise from the bottom side to take up the tape. Fig. S11 D. Rotate the Main Cam Gear clockwise until the cassette tape is ejected. 2.3. INTRODUCTION OF VIDEO HEAD CLEANING CASSETTE / (POLISHING TYPE) 1. We are pleased to introduce Panasonic Video Head Cleaning...
Page 9
Cassette, VFK0923FT [for service purposes] and VFK0923FSE [ for end users] for all VHS/SVHS VCP and VCR. 2. These cleaning cassettes are exclusive removing the hard and sticky clogging on video heads. 3. These improve the efficiency of video head cleaning service and shortening cleaning time for end users.
Page 10
VFK0823FSE (For end users) Type of Cassette Full VHS Cassette Cleaning Time 10 Seconds/Time Tape Length 3.34 m Usability in a Path 30 Times Note: The tape material itself is the same in both types. 2.4. SELF-DIAGNOSIS RESULT DISPLAY The "SELF-DIAGNOSIS RESULT DISPLAY & MEMORY function is built in this VTR. It means that when the VCR detects undesirable condition, it can be displayed a “Error code (Two numbers from the right)”...
Page 11
INDICATION CAUSE REMEDY/CHECK After cylinder lock is detected, the cylinder Check the cylinder motor drive circuit. does not start rotating again even after tape unloading. Cassette tape is not wound up during the tape Check the capstan motor drive circuit. unloading except EJECT mode.
Page 12
3.1.2. DETAIL OF DISASSEMBLY METHOD 1. REMOVAL OF THE TOP PANEL Remove 4 Screws (A) Fig.D2 2. REMOVAL OF THE FRONT PANEL UNIT Unlock 7 Tabs (B) Fig. D3...
Page 13
3. REMOVAL OF THE MECHANISM UNIT Remove Screw (C) Remove 3 Screws (D) Remove 2 Screws (E) Note: 1. Keep pressing 2 stoppers on Cassette Holder Plate and Press Cassette Holder Plate to the rear. 2. Remove the Mechanism Unit after bend the Cylinder Shield in the direction of the arrow.
Page 14
Remove 4 Screws (F) Unlock 4 Tabs (G) Fig. D5 NOTE: Before mounting the MAIN C.B.A. onto the frame, be sure to confirm that the insulation sheet is mounted on the frame as shown in Fig. D6 Fig. D6 5. REMOVAL OF THE SECAM C.B.A. Unlock 2 Tabs (H) Fig.
Page 15
6. SERVICING POSITION Fig. D8 3.2. MECHANICAL ADJUSTMENT PROCEDURES Refer to the Service Manual for Z-Mechanism Chassis. / (Order No. VRD9802005C2) 3.3. ELECTRICAL ADJUSTMENT PROCEDURES 3.3.1. TEST EQUIPMENT The following equipments are required for Electrical Adjustments. 1. Dual-Trace Oscilloscope - Voltage Range: 0.005-5V/div - Frequency Range: DC-35MHz - Probes: 10:1 / 1:1 2.
Page 16
5. Video Sweep Generator 6. Sinewave Generator 7. Video Pattern Generator 8. Monitor TV 9. DC Power Supply 10. VHS/S-VHS Blank Tape 11. VHS Alignment Tape - Parts No.: VFJ8125H3F(PAL) 3.3.2. VCR SETTING When no indication in the procedure, set each selector as follows. 1.
Page 17
Fig.E1 Fig.E2 Fig.E3 CONDITION: BURST SIGNAL OFF / CONDITION: BURST SIGNAL 75ohm TERMINATED 75ohm TERMINATED Fig.E4 3.3.4. PG SHIFTER ADJUSTMENT / (AUTOMATIC) PROCEDURES FIP DISPLAY Press the FF and EJECT Keys simultaneously for 3 seconds. Press the FF and EJECT Keys simultaneously twice.
Page 18
PROCEDURES FIP DISPLAY When the sequence of the automatical adjustment has been terminated, the following action has been made. *SUCCEED: The cassette tape is ejected. *ERROR : The "F2"is displayed on the FIP. (Check the Servo/Syscon circuit and Cylinder unit.) Release the Service mode by pressing the EJECT and FF keys simultaneously in 6 times until the FIP becomes normal indication.
Page 19
PROCEDURES FIP DISPLAY Store the Adjusted value by pressing the "5" key on the Remote Controller. Release the Service mode by pressing the EJECT and FF keys simultaneously in 6 times until the FIP becomes normal indication. Fig. E6 3.3.6. VHS VIDEO FREQUENCY RESPONSE ADJUSTMENT PROCEDURES FIP DISPLAY Set the S-VHS ET REC to OFF in...
Page 20
Fig. E7 3.3.7. LOCATION OF TEST POINTS & CONTROLS 3.3.8. CIRCUIT BOARD LAYOUT 4. ABBREVIATIONS 5. INPUT/OUTPUT CHART 5.1. INPUT/OUTPUT CHART FOR IC6001 5.2. TRUTH TABLE...
Page 25
11. REPLACEMENT PARTS LIST 11.1. CHASSIS PARTS SECTION PARTS LIST - All parts except parts mentioned [AVC-SPC] in the Remarks column are supplied from MAVD. Parts mentioned [AVC-SPC] are supplied from PAVC-CSG (AVC- SPC).
Page 26
Ref. No. Part No. Part Name & Description Remarks VEG1601 CYLINDER UNIT VXP2174 UPPER CYLINDER UNIT VDB1256 CYLINDER RETAINER VEM0715 CYLINDER MOTOR UNIT VXS0135 EARTH BRUSH UNIT VMD3795 FLAT CABLE HOLDER VEK9069 CAPSTAN UNIT L1AZ00000004 FE HEAD VDB1431 TENSION ARM BOSS VDB1460 SUPPLY BRAKE ARM BOSS VDG1220KIT...
Page 27
Ref. No. Part No. Part Name & Description Remarks VMD3379 SIDE PLATE (L) VXA6540 SIDE PLATE (R) UNIT VXA5746 CASSETTE HOLDER UNIT VXP1730 MAIN SHAFT UNIT VHD1117 SCREW VHD1117 SCREW VHD0842 SCREW VHD0843 SCREW VHD0843 SCREW VHD0844 SCREW VHD0844 SCREW VHD1066 SCREW VHD1066...
Page 28
Ref. No. Part No. Part Name & Description Remarks VGM1990 TOP PANEL silver VYP8699 FRONT PANEL U SV120 RKA0072-K FOOT RKA0072-K FOOT VYF2892 DOOR UNIT VGB0554 SUPER DRIVE BADGE VKF3706 BLINDER PANEL VMB2521 BLINDER SPRING VKU0575 BOTTOM PLATE VMZ3099-W V0 SHEET VMZ3099 VJH1175 JACK BOARD...
Page 30
Ref. No. Part No. Part Name & Description Remarks VEP06F09D MAIN C.B.A. (RTL) THE FOLLOWING C.B.A. IS INCLUDED IN MAIN C.B.A. VEP07A47A-SK VEP07A47A-SK TV DEMODULATOR PACK C.B.A. (RTL) INCLUDED IN MAIN C.B.A.(VEP06F09D). VEP03G25A S-VHS PACK C.B.A. (RTL) VEP04832A FRONT C.B.A. (RTL) VEP08328A SECAM C.B.A.
Page 58
Pin No. Signal Name P-OFF P-SAVE P-FAIL Reset Describe A.DEF(H) O Output signal for audio defea and decoder IC reset. Detection of COLOR KILLER active. CKILLER DET(L) AFC S S curve input from tuner. Output signal depens on tape speed. SLP(H) (During N10H or P9H: High) (Except N10H and P9H: Low)
Page 59
Pin No. Signal Name P-OFF P-SAVE P-FAIL Reset Describe Input terminal for mechanism position. POS.SW3 D.A.REC(H) POS.SW2 BIAS(L) 140mS 140mS POS.SW1 RESET(L) MICOM reset input terminal. 32KHz IN Sub oscillator input. 32KHz OUT O Sub oscillator output. +5V(D) Power. 12MHz.IN Main oscillator input.
Page 60
Pin No. Signal Name P-OFF P-SAVE P-FAIL Reset Describe HALF_WAVE(H) O Control signal for switching capstan motor mode FAST and SLOW. CAP.ET O Torque control signal for capstan motor. CYL.ET O Torque control signal for cylinder motor. 4.213V 4.213V 4.213V P FAIL Interrupt input signal for power fail detection.
Page 66
Mute signals INPUT CONDITION Audio Output Results IC4501 settings POWER INPUT RF (C) AV1 Out AV2 Out REC/ Input Mute A-Mute SELECT VV ON(H) PB(H) Selector Selector Select Select P.ON NO.TU VIDEO INSEL OUTSEL S-VIDEO C+.TU VIDEO INSEL OUTSEL S-VIDEO VIDEO AV1IN AV1IN...
Page 67
Mute signals INPUT CONDITION Audio Output Results IC4501 settings POWER INPUT RF (C) AV1 Out AV2 Out REC/ Input Mute A-Mute SELECT VV ON(H) PB(H) Selector Selector Select Select P.ON DECODER NO.TU VIDEO AV1IN AV1IN EXT1 S-VIDEO VIDEO AV2IN AV1IN AV2IN AV1IN EXT2...
Page 68
Mute signals INPUT CONDITION Audio Output Results IC4501 settings POWER INPUT RF (C) AV1 Out AV2 Out REC/ Input Mute A-Mute SELECT VV ON(H) PB(H) Selector Selector Select Select P.ON DECODER NO.TU VIDEO AV1IN AV1IN EXT1 S-VIDEO VIDEO AV1IN AV1IN EXT1 S-VIDEO C+.TU...
Page 69
SYSTEM CONTROL & SERVO ICs DC VOLTAGE CHART (SP MODE) IC1501 IC1502 Ref. No. MODE STOP PLAY IC2501 Ref. No. MODE STOP 15.4 15.4 15.6 -0.1 15.4 PLAY 15.0 15.0 15.2 15.0 15.1 15.0 15.3 -0.1 15.0 14.7 14.6 14.9 15.0 14.6 14.6...
Page 70
4.43 NTSC L BILINGUAL 443NT [L] BILINGUAL L A. COMP BIL [L] AUDIO COMPONENT SIGNAL BILINGUAL H BIL. [H] A. COMPO AUDIO COMPONENT SIGNAL BILINGUAL L AUDIO DUBBING PAUSE L BIL/M1 [L] A. D.P [L] AUDIO DUBBING PAUSE L BS CLOCK A.
Page 71
CYL GND CYLINDER GND FULL. E. 12V FULL ERASE 12V DELAIED FM RECORDING H D.F.M. REC [H] GND (ANALOG) GND [A] DELAIED FM RECORDING L D. FM REC [L] GND (TUNER) GND [TU] D. GND GND/NON SW 12V DIGITAL GND GND/N.
Page 72
POWER OFF H LINE IN [R] LINE INPUT (R) P-OFF [H] POWER OFF L LINE OUT [L] LINE OUTPUT (L) P-OFF [L] LINE OUT [R] LINE OUTPUT (R) P. FAIL POWER FAILURE DETECT LP H POWER OFF H LP [H] P.
Page 73
SYSTEM CONTROL 5V RF OUT RF OUTPUT SYSCON 5V SYSTEM SW RF Y RF LUMINANCE SIGNAL SYSTEM TAKE-UP PHOTO TRANSISTOR RF. Y. IN RF LUMINANCE SIGNAL INPUT T-PHOTO TAKE-UP REEL PULSE RF. Y. OUT RF LUMINANCE SIGNAL OUTPUT T-RL. PLS TIMER BUS CLOCK ROTAR.
Page 74
8 SCHEMATIC DIAGRAMS 8.1. POWER TRANSFORMER SECTION IN MAIN SCHEMATIC DIAGRAM THE STRIPED FRAME INDICATES THE PRIMARY CIRCUIT TO DISTINGUISH THE PRIMAR CAUTION FROM THE SECONDARY CIRCUIT. PAY ATTENTION NOT TO RECEIVE AN ELECTRIC SHOCK DURING REPAIR AND SERVIC THE PRODUCTS. C1121 1000P P1101...
Page 75
0.01 2200 RM ON THE POWER TRANSFORMER NG POINT AS FOLLOWS. NV-SV120EF NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR POWER TRANSFORMER E IS SHOWN THE VOLTAGE WHEN ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST.
Page 76
8.2. POWER SUPPLY/ RF SECTION IN MAIN SCHEMATIC DIAGRAM VIDEO MAIN SIGNAL PATH IN REC MODE AUDIO MAIN SIGNAL P P :TO POWER TRANSFORMER SECTION :TO SYSTEM CONTROL & SERVO SECTION V :TO LUMINANCE & CHROMINANCE/AUDEIO SECTION Q1013 Q1003 :TO Hi-Fi AUDIO SECTION 2SD601A 2SB710A :TO INPUT/OUTPUT SECTION...
Page 77
0.01 R7614 D1009 MA4033H R7613 D1010 MA165 NV-SV120EF NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS POWER SUPPLY/RF SCHEMATIC DIAGRAM FOR ORDERING.WHEN YOU SECTION SCHEMATIC DIAGRAM ORDER A PART,PLEASE REFER TO PARTS LIST. N THIS DIAGRAM IS STOP MODE.
Page 78
8.3. TIMER SECTION IN MAIN SCHEMATIC DIAGRAM P :TO POWER TRANSFORMER SECTION DP7501 A2BA00000212 R :TO POWER SUPPLY/RF SECTION S :TO SYSTEM CONTROL & SERVO SECTION :TO INPUT/OUTPUT SECTION S-VHS P10 P11 P12 P1 R7507 HEATER (+) C7501 0.01 HEATER DC (-) D7501 C7502 R7511...
Page 79
EVQ11404M C7509 6800P R7503 R7502 R7501 R7538 4300 5600 8200 TIMER CHECK EJECT S7505 S7517 EVQ11L07B EVQ11L07B R7522 R7519 R7536 R7520 8200 4300 5600 NV-SV120EF N ON THIS SCHEMATIC DIAGRAM FOR ART,PLEASE REFER TO PARTS LIST. TIMER SECTION SCHEMATIC DIAGRAM...
Page 80
8.4. SYSTEM CONTROL & SERVO SECTION IN MAIN SCHEMATIC DIAGRAM CAPSTAN SERVO SPEED LOOP CAPSTAN SERVO PHASE LOOP :TO POWER TRANSFORMER SECTION :TO POWER SUPPLY/RF SECTION :TO LUMINANCE & CHROMINANCE/AUDIO SECTION A27 A28 :TO Hi-Fi AUDIO SECTION I :TO INPUT/OUTPUT SECTION :TO TIMER SECTION R1017 R2501...
Page 83
UNREG 14V R2509 C2517 C6001 6V47 6V47 L2501 L6001 100u PS 12V NV-SV120EF SYSTEM CONTROL & SERVO NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST. SECTION SCHEMATIC DIAGRAM...
Page 84
8.5. LUMINANCE & CHROMINANCE/ AUDIO SECTION IN MAIN SCHEMATIC DIAGRA R :TO POWER SUPPLY/RF SECTION VIDEO MAIN SIGNAL PATH IN REC MODE :TO SYSTEM CONTROL & SERVO SECTION VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE :TO Hi-Fi AUDIO SECTION AUDIO MAIN SIGNAL PATH IN REC MODE :TO INPUT/OUTPUT SECTION AUDIO MAIN SIGNAL PATH IN PLAYBACK MODE MUTE...
Page 85
2SD601A (PB:ON) C4013 C4014 R4013 0.01 6V47 R4012 R4010 R4009 R4011 NV-SV120EF THE MEASUREMENT MODE OF THE DC VOLTAGE OUT OF THE BRACKETS ON THIS DIAGRAM IS PLAYBACK MODE WITH SECAM COLOUR SIGNAL.(SP MODE) LUMINANCE & CHROMINANCE/AUDIO SECTION SCHEMATIC DIAGRAM...
Page 86
C3013 C3058 R3038 C3014 C3053 C3008 C3009 6200 5600 0.01 50V4.7 C3012 6V47 C3005 R3001 C3001 L3002 C3011 1500 150P 0.01 R3037 1200 R3033 NV-SV120EF NOTE:DO NOT USE ANY PART NUMBE LUMINANCE & CHROMINANCE/AUDIO SECTION SCHEMATIC DIAGRAM ORDERING.WHEN YOU ORDER...
Page 87
:ON) FREQ.ADJ R3037 L3010 C3054 QR3006 1200 UN2212 S-VHS (S-VHS :ON) Y/C VIDEO OUT NV-SV120EF LUMINANCE & CHROMINANCE/AUDIO USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR NG.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST. SECTION SCHEMATIC DIAGRAM...
8.6. Hi-Fi AUDIO SECTION IN MAIN SCHEMATIC DIAGRAM :TO POWER SUPPLY/RF SECTION AUDIO MAIN SIGNAL PATH IN REC MODE AUDIO MAIN SIGNAL PATH IN PLAY :TO SYSTEM CONTROL & SERVO SECTION :TO LUMINANCE & CHROMINANCE/AUDIO SECTION :TO INPUT/OUTPUT SECTION L4502 :TO DECODER SECTION 1.2u C4525...
Page 89
R4517 C4516 C4505 10V33 L4501 1.2u NV-SV120EF NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS KETS ON THIS DIAGRAM IS PLAYBACK MODE SCHEMATIC DIAGRAM FOR ORDERING.WHEN YOU Hi-Fi AUDIO SECTION SCHEMATIC DIAGRAM ORDER A PART,PLEASE REFER TO PARTS LIST.
Page 90
8.7. INPUT/ OUTPUT SECTION IN MAIN SCHEMATIC DIAGRAM :TO POWER SUPPLY/RF SECTION VIDEO MAIN SIGNAL PATH IN REC MODE VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE :TO SYSTEM CONTROL & SERVO SECTION :TO LUMINANCE & CHROMINANCE/AUDIO SECTION :TO Hi-Fi AUDIO SECTION R4901 C4903 T :TO TIMER SECTION...
Page 91
:ON) R4912 Q4903 2SD601A R3040 R4925 (PROG :ON) 4700 4700 NV-SV120EF INPUT/OUTPUT SECTION HIS DIAGRAM IS PLAYBACK MODE NOTE:DO NOT ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST. SCHEMATIC DIAGRAM...
8.8. DECODER SECTION IN MAIN SCHEMATIC DIAGRAM R :TO POWER SUPPLY/RF SECTION S :TO SYSTEM CONTROL & SERVO SECTION A :TO Hi-Fi AUDIO SECTION C7628 IC7601 C0EAH0000051 (RESET) SIF2 C7624 R7623 INPUT SWITCH VREF1 AGC, L7607 R7615 C7625 2.2u 0.01 SIF1 R7618 CRESET...
Page 93
OUT L MONO ANALOG CROSSBAR CHANNEL SWITCH OUTPUT BUFFERS IC7602 TDA9874AH R7628 LB7603 C7635 C7634 6V47 J0JCC0000124 100P TL7601 TL7602 C7638 TL7603 BER SHOWN ON THIS SCHEMATIC DIAGRAM FOR NV-SV120EF R A PART,PLEASE REFER TO PARTS LIST. DECODER SECTION SCHEMATIC DIAGRAM...
Page 94
8.9. SECAM SCHEMATIC DIAGRAM VIDEO MAIN SIGNAL PATH IN REC MODE R8803 120K VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE C880 50V2 SECAM SYNC SECAM SENS SYNC GETE GENE/ GENE V-SEP TO MUTE/ SYNC GATE P8801 P3003-15 C SYNC P3003-14 IC8801 P3003-13 LA70100M...
(5.0) UN2111 (PB SECAM:ON) (5.0) QR8804 Q8801 UN2211 2SD601A (PB:ON) (AMP) R8804 (2.1) (4.9) NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR ORDERING.WHEN YOU NV-SV120EF ORDER A PART,PLEASE REFER TO PARTS LIST. SECAM PACK SCHEMATIC DIAGRAM...
Page 96
8.10. S-VHS PACK SCHEMATIC DIAGRAM VIDEO MAIN SIGNAL PATH IN REC MODE VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE PS3301 V MASK SYS IIC DATA SYS IIC CLOCK PS 3.3V L3301 C IN DNR 5V PB C C3383 C3355 R3313 R3314 6V0.47 EMPHA OUT...
(2.3) R3367 1100 C3386 C3387 L3309 C3385 100u CRADJ SSEP R3365 R3364 (1.9) Q3317 2SB1218A (AMP) 3362 C3345 C3343 C3342 50V4.7 0.01 16V10 NV-SV120EF DC VOLTAGE OUT OF THE BRACKETS ON THIS DIAGRAM IS PLAYBACK MODE S-VHS PACK SCHEMATIC DIAGRAM...
Page 98
(3D Y/C SEP & 3D NR TBC) C3307 C3311 C3309 L3312 C3308 1500P C3379 NV-SV120EF NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM S-VHS PACK SCHEMATIC DIAGRAM FOR ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST.
Page 99
ENCODER HD OUT (BURST CHANGE) VD OUT BLACK VDD IO2 DELAY EXPANSION ADJ. (SYNC OSD A2 CHANGE) C3301 OSD A1 OSD B OSD G OSD R C3307 C3306 C3305 NV-SV120EF CHEMATIC DIAGRAM S-VHS PACK SCHEMATIC DIAGRAM REFER TO PARTS LIST.
8.11. TV DEMODULATOR PACK SCHEMATIC DIAGRAM VIDEO SIGNAL PATH AUDIO SIGNAL PAT PP0701 (TO TUNER) 4MHz R0735 C0730 R0734 16V22 6800 C0703 R0711 0.01 5600 R0727 X0706 VLF1372 C0728 C0717 L0706 50V0.1 0.01 150u D0703 C0706 MA80WK 0.01 R0710 L0707 150u R0709 C0705...
Page 101
C0725 50V2.2 VR0701 10KB C0715 C0716 C0726 0.01 390P 1500P C0735 R0722 R0717 R0755 R0756 R0737 0.01 5600 5600 NV-SV120EF NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR OU ORDER A PART,PLEASE REFER TO PARTS LIST. TV DEMODULATOR PACK SCHEMATIC DIAGRAM...
Page 102
8.12. FRONT SCHEMATIC DIAGRAM VIDEO MAIN SIGNAL PATH IN REC MODE AUDIO MAIN SIGNAL PATH IN REC MODE IC4801 PNA4618M10V JK4801 (IR RECEIVER) K2HA307A0003 AUDIO AUDIO VIDEO IN (R/N) IN (L) C4805 C4806 L4802 L4801 R4801 BOTTOM PLATE R4803 R4802 C4804 C4803 1000P...
Page 104
P2502-5 P2502-4 P2502-3 MAIN COIL 1 P2502-2 P2502-1 NV-SV120EF CYLINDER STATOR NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR SCHEMATIC DIAGRAM ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST. 8.14. CAPSTAN UNIT SCHEMATIC DIAGRAM R0206...
Page 105
R0212 R0213 Q0203 Q0202 Q0201 R0210 D0203 TL0204 TL0202 TL0203 TL0201 L0201 C0208 R0204 C0210 C0209 OUT2 CAPSTAN MOTOR DRIVER MAIN COIL OUT1 TL0205 DRIVER CONTROL LOGIC NV-SV120EF CAPSTAN UNIT SCHEMATIC DIAGRAM...
Page 108
AUDIO HEAD P5001 MUTE FROM TV TUNER AUDIO (N) DEMODULATOR FM MODULATOR/ DEMODULATOR NORMAL P4002 A.HEAD (W) MUTE SELECT SWITCH TO/FROM FROM MUTE AC HEAD & MUTE H SYSTEM SWITCH CONTROL P4002 MUTE A.HEAD (R) TRAP NV-SV120EF AUDIO BLOCK DIAGRAM...
Page 109
P3003 P8801 SYSTEM CONTROL MUTE MUTE BUFFER BUFFER REC/PB QR8802 P3003 P8801 SECAM FROM SYSTEM QR8803 CONTROL P3003 P8801 V.EE QR8804 Q8801 P3003 P8801 PB SECAM C BUFFER LUMINANCE & CHROMINANCE P3003 P8801 REC SECAM C NV-SV120EF SECAM BLOCK DIAGRAM...
Page 110
(3D YC SEP & 3D NR TBC) DECODER 4FSC Q3312 BUFFER BIAS BLACK DELAY EXPANSION & ADJ. SAMPLING FEED-BACK SYNC CHANGE CLAMP 8FSC 4FSC PEDESTAL CLAMP DELAY 3D NR ADJ. ENCODER BURST SAMPLING 8FSC CHANGE SYNCHRONIZATION PROCESSING TIMING CONTROL NV-SV120EF S-VHS BLOCK DIAGRAM...
Page 111
S7512 S7511 S7504 Q1501 D1501 Q1502 S7507 TAKE UP SENSOR SUPPLY SAFETY 79 S-REEL PULSE PHOTO PHOTO TAB SW SENSOR SENSOR 7 AN0 P4002 94 CTL HEAD (-) HEAD P4002 CTL HEAD (+) NV-SV120EF SYSTEM CONTROL & SERVO BLOCK DIAGRAM...
Page 112
VIDEO/Y IN TV DEMODULATOR V IN1 TUNER VIDEO CLAMP C OUT REC C C IN1 JK4801 VIDEO IN PS4801 PP3901 FRONT VIDEO IN JK4802 S-VIDEO PS4801 PP3901 FRONT C IN PS4801 PP3901 FRONT Y IN NV-SV120EF LUMINANCE & CHROMINANCE BLOCK DIAGRAM...
Page 113
VIDEO HEAD P5001 LP/EP R C CLOCK EXTERNAL PB LUMINANCE TO C CCD DRIVER SIGNAL INPUT LINE (NOT USED IN THESE MODELS) TO SYSTEM CONTROL S-VHS S-VHS DET H NV-SV120EF NV-SV120EF LUMINANCE & CHROMINANCE BLOCK DIAGRAM LUMINANCE & CHROMINANCE BLOCK DIAGRAM...
Page 114
L0201 R0208 UNLOADING C0208 HOLE LOADING SENSOR R0204 C0210 C0209 ED/S TORQUE DIRECTION OUT2 CAPSTAN MOTOR DRIVER MAIN COIL HALL R0209 POWER EC AMP OUT1 HOLE SENSOR TL0205 DRIVER CONTROL LOGIC R0201 R0211 C0206 C0207 NV-SV120EF CAPSTAN UNIT SCHEMATIC DIAGRAM...
Page 115
P2502-7 P2502-6 HALL IC GND (CYL) P2502-5 P2502-4 P2502-3 MAIN COIL 1 P2502-2 P2502-1 NV-SV120EF CYLINDER STATOR NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR SCHEMATIC DIAGRAM ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST.
Page 116
C7638 TL7603 NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR NV-SV120EF NOTE:THE MEASUREMENT MODE OF THE DC VOLTAGE ON THIS DIAGRAM IS STOP MODE. ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST. DECODER SECTION SCHEMATIC DIAGRAM...
D.FM REC L4501 1.2u NV-SV120EF NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS NOTE:THE MEASUREMENT MODE OF THE DC VOLTAGE IN THE BRACKETS( )ON THIS DIAGRAM IS RECORD MODE THE MEASUREMENT MODE OF THE DC VOLTAGE OUT OF THE BRACKETS ON THIS DIAGRAM IS PLAYBACK MODE SCHEMATIC DIAGRAM FOR ORDERING.WHEN YOU...
Page 118
5600 8200 NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST. NV-SV120EF NOTE:THE MEASUREMENT MODE OF THE DC VOLTAGE ON THIS DIAGRAM IS STOP MODE. FRONT SCHEMATIC DIAGRAM...
Page 119
4700 GND (AV) GND (FIP) NV-SV120EF INPUT/OUTPUT SECTION NOTE:THE MEASUREMENT MODE OF THE DC VOLTAGE IN THE BRACKETS( )ON THIS DIAGRAM IS RECORD MODE THE MEASUREMENT MODE OF THE DC VOLTAGE OUT OF THE BRACKETS ON THIS DIAGRAM IS PLAYBACK MODE NOTE:DO NOT ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR WITH SECAM COLOUR SIGNAL.(SP MODE)
Page 120
0.01 2200 NOTE1:WHEN MEASURE THE VOLTAGE OR WAVEFORM ON THE POWER TRANSFORMER CIRCUIT,SET THE GND TERMINAL OF MEASURING POINT AS FOLLOWS. NV-SV120EF PRIMARY SIDE..SECONDARY SIDE... IMPORTANT SAFETY NOTICE: NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR...
D1002 C1011 D1005 25V47 MA4056NH 25V47 MA4056NH NV-SV120EF IMPORTANT SAFETY NOTICE: NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS POWER SUPPLY/RF COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS FOR SAFETY. SCHEMATIC DIAGRAM FOR ORDERING.WHEN YOU SECTION SCHEMATIC DIAGRAM WHEN REPLACING ANY OF THESE COMPONENTS,USE ONLY THE SAME TYPE.
Page 122
NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS THE MEASUREMENT MODE OF THE DC VOLTAGE OUT OF THE BRACKETS ON THIS DIAGRAM IS PLAYBACK MODE SCHEMATIC DIAGRAM FOR ORDERING.WHEN YOU NV-SV120EF WITH SECAM COLOUR SIGNAL.(SP MODE) ORDER A PART,PLEASE REFER TO PARTS LIST.
Page 123
16V10 C3374 270P NV-SV120EF NOTE:THE MEASUREMENT MODE OF THE DC VOLTAGE IN THE BRACKETS( )ON THIS DIAGRAM IS RECORD MODE THE MEASUREMENT MODE OF THE DC VOLTAGE OUT OF THE BRACKETS ON THIS DIAGRAM IS PLAYBACK MODE S-VHS PACK SCHEMATIC DIAGRAM WITH PAL COLOUR SIGNAL.(SP MODE)
Page 124
C3307 C3306 C3305 C3311 C3309 L3312 C3308 1500P C3379 NV-SV120EF NV-SV120EF NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM S-VHS PACK SCHEMATIC DIAGRAM S-VHS PACK SCHEMATIC DIAGRAM FOR ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST.
Page 126
6V47 L2501 L6001 100u PS 12V NV-SV120EF NV-SV120EF SYSTEM CONTROL & SERVO NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST. SYSTEM CONTROL & SERVO SECTION SCHEMATIC DIAGRAM...
Page 127
6V220 4300 5600 BACK UP 5V NV-SV120EF NOTE:DO NOT USE PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR NOTE:THE MEASUREMENT MODE OF THE DC VOLTAGE ON THIS DIAGRAM IS STOP MODE. ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST.
Page 128
5600 5600 NOTE:DO NOT USE PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR NV-SV120EF NOTE:THE MEASUREMENT MODE OF THE DC VOLTAGE ON THIS DIAGRAM IS STOP MODE. ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST. TV DEMODULATOR PACK SCHEMATIC DIAGRAM...
Page 129
R4010 PS 5V VIDEO 5V NV-SV120EF NOTE:THE MEASUREMENT MODE OF THE DC VLOLTAGE IN THE BRACKETS( )ON THIS DIAGRAM IS RECORD MODE THE MEASUREMENT MODE OF THE DC VOLTAGE OUT OF THE BRACKETS ON THIS DIAGRAM IS PLAYBACK MODE WITH SECAM COLOUR SIGNAL.(SP MODE) WITH SECAM COLOUR SIGNAL.(SP MODE)
Page 130
UN2212 S-VHS R3033 (S-VHS :ON) Y/C VIDEO OUT NV-SV120EF LUMINANCE & CHROMINANCE/AUDIO NV-SV120EF NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR LUMINANCE & CHROMINANCE/AUDIO SECTION SCHEMATIC DIAGRAM ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST.
Page 131
(VEM0715) CYLINDER STATOR UNIT Integrated Circuit HALL IC Connector M1 VM P2901 ADDRESS INFORMATION HALL IC VM M2 P2901 NV-SV120EF CYLINDER STATOR UNIT...
Page 132
FRONT C.B.A. Integrated Circuit IC4801 Connector PS4801 ADDRESS INFORMATION (VEP04832A) NV-SV120EF FRONT C.B.A.