Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DeWalt XR LI-ION DCG405N
Summary of Contents for DeWalt XR LI-ION DCG405N
- Page 1 DCG405...
- Page 2 English (original instructions) Copyright D WALT...
- Page 3 Fig. A 90˚ 90˚ A9 KR A9 only Fig. B...
- Page 4 Fig. C Fig. D Fig. E TW B1 IN Fig. F Fig. G...
-
Page 5: Technical Data
English CORDLESS SMALL ANGLE GRINDER DCG405 Congratulations! You have chosen a D WALT tool. Years of experience, thorough product development and innovation make D WALT one of the most reliable partners for professional power tool users. Technical Data DCG405-IN DCG405-B1/TW DCG405-A9 DCG405-KR Voltage 18(20 Max) -
Page 6: Definitions: Safety Guidelines
English c ) Do not expose power tools to rain or wet conditions. WARNING: To reduce the risk of injury, read the Water entering a power tool will increase the risk of instruction manual. electric shock. Definitions: Safety Guidelines d ) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. -
Page 7: Safety Instructions For All Operations
English c ) Disconnect the plug from the power source and/or b ) Operations such as polishing are not recommended the battery pack from the power tool before making to be performed with this power tool. Operations any adjustments, changing accessories, or storing for which the power tool was not designed may create power tools. -
Page 8: Causes And Operator Prevention Of Kickback
English k ) Never lay the power tool down until the accessory snag the rotating accessory and cause loss of control has come to a complete stop. The spinning accessory or kickback. may grab the surface and pull the power tool out of e ) Do not attach a saw chain woodcarving blade or your control. -
Page 9: Using An Extension Cable
English otherwise kickback may occur. Investigate and take • Risk of dust from hazardous substances. corrective action to eliminate the cause of wheel binding. Electrical Safety d ) Do not restart the cutting operation in the The electric motor has been designed for one voltage only. workpiece. -
Page 10: Charger Operation
English Charger Operation • These chargers are not intended for any uses other than charging D WALT rechargeable batteries. Any other uses Refer to the indicators below for the charge status of the may result in risk of fire, electric shock or electrocution. battery pack. - Page 11 English exposed. Align the slots on the back of the charger with the a hammer, stepped on). Electric shock or electrocution exposed screws and fully engage them in the slots. may result. Damaged battery packs should be returned to service centre for recycling. Charger Cleaning Instructions WARNING: Fire hazard.
-
Page 12: Storage Recommendations
English Use Mode: When the FLEXVOLT battery stands alone or is Have defective cords replaced immediately. in a D WALT 18V (20V Max) product, it will operate as an 18V (20V Max) battery. When the FLEXVOLT battery is in a 54V (60V Max) or a 108V (120V Max) (two 54V (60V Max) batteries) Charge only between 4 ˚C and 40 ˚C. - Page 13 English Power-OFF™ Overload Protection Wear ear protection. The power supply to the motor will be reduced in case of motor overload. With continued motor overload, the tool will shut off. The switch will need to be released then depressed Wear eye protection. to restart tool.
- Page 14 English To actuate the fuel gauge, press and hold the fuel gauge button. installing attachments or accessories. An accidental A combination of the three green LED lights will illuminate start-up can cause injury. designating the level of charge left. When the level of charge Adjusting the guard in the battery is below the usable limit, the fuel gauge will not For guard adjustment, the guard release lever ...
- Page 15 English 1. Loosen screw, until the guard lug 19 can rotate freely in the WARNING: Proper guard must be reinstalled for grinding groove 20 on the gear case hub. wheel, cutting wheel, sanding flap disc, wire brush or wire wheel applications after sanding applications 2.
- Page 16 English Prior to Operation • Be aware, the wheel continues to rotate after the tools is switched off. • Install the guard and appropriate disc or wheel. Do not use Proper Hand Position (Fig. G) excessively worn discs or wheels. • Be sure the backing and locking flange are mounted WARNING: To reduce the risk of serious personal injury, correctly.
- Page 17 English 1. Allow the tool to reach full speed before touching the tool 3. NO EATING, DRINKING or SMOKING should be done in the to the work surface. work area to prevent ingesting contaminated paint particles. Workers should wash and clean up BEFORE eating, drinking 2.
-
Page 18: Cutting Metal
After Service and Repair WARNING: To reduce the risk of serious personal • DEWALT service centers are staffed with trained personnel to injury, turn tool off and disconnect battery pack provide customers with efficient and reliable product service. before making any adjustments or removing/ •... -
Page 19: Accessory Chart
English Accessory Chart guard Type Accessory Description how to Fit grinder Depressed centre grinding disc Type 27 Type 27 guard Guard Flap wheel Backing flange Type 27 Guard Wire wheels Type 27 depressed centre wheel Locking flange Wire wheels with threaded nut Type 27 guard Wire wheel... - Page 20 English Accessory Chart (cont.) guard Type Accessory Description how to Fit grinder Masonry cutting disc, bonded Type 1 Type 1 guard Guard Metal cutting disc, bonded Backing flange Type 27 Guard Diamond cutting wheels Cutting wheel Type 1 Guard Locking flange Type 27 Guard Type 27...