Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DeWalt DCG405H2T
Summary of Contents for DeWalt DCG405H2T
- Page 1 DCG405...
- Page 2 English (original instructions) Copyright D WALT...
- Page 3 Fig. A 90˚ 90˚ Fig. B...
- Page 4 Fig. C Fig. D Fig. E Fig. F Fig. G...
-
Page 5: Definitions: Safety Guidelines
English CORDLESS SMALL ANGLE GRINDER DCG405 Congratulations! EC-Declaration of Conformity You have chosen a D WALT tool. Years of experience, thorough Machinery Directive product development and innovation make D WALT one of the most reliable partners for professional power tool users. Technical Data Cordless Small Angle Grinder DCG405... -
Page 6: Save All Warnings And Instructions For Future Reference
English Batteries Chargers/Charge Times (Minutes)*** DCB112/ DCB115/ Weight (kg) DCB104 DCB107 DCB113 DCB116 DCB117 DCB118 DCB132 DCB119 Cat # DCB1102 DCB1104 DCB546 18/54 6.0/2.0 1.08 DCB547 18/54 9.0/3.0 1.46 135* 110* 135* DCB548 18/54 12.0/4.0 1.46 DCB549 18/54 15.0/5.0 2.12 DCB181 0.35 DCB182... -
Page 7: Additional Specific Safety Rules
English e ) Do not overreach. Keep proper footing and balance a connection from one terminal to another. Shorting at all times. This enables better control of the power tool the battery terminals together may cause burns or a fire. in unexpected situations. d ) Under abusive conditions, liquid may be ejected f ) Dress properly. -
Page 8: Causes And Operator Prevention Of Kickback
English h ) Wear personal protective equipment. Depending on movement at the point of pinching. Abrasive wheels may also application, use face shield, safety goggles or safety break under these conditions. glasses. As appropriate, wear dust mask, hearing Kickback is the result of power tool misuse and/or incorrect protectors, gloves and workshop apron capable of operating procedures or conditions and can be avoided by taking stopping small abrasive or workpiece fragments. - Page 9 English f ) Do not use worn down wheels from larger power b ) If the use of a guard is recommended for wire tools. Wheel intended for larger power tool is not suitable brushing, do not allow any interference of the wire wheel or brush with the guard.
-
Page 10: Important Safety Instructions For All Battery Chargers
English Chargers Do not operate charger if it has received a sharp blow, • been dropped, or otherwise damaged in any way. Take it WALT chargers require no adjustment and are designed to be to an authorised service centre. as easy as possible to operate. Do not disassemble charger;... -
Page 11: Wall Mounting
English Do not charge or use battery in explosive atmospheres, hot/Cold Pack Delay • such as in the presence of flammable liquids, gases or When the charger detects a battery pack that is too hot or too dust. Inserting or removing the battery from the charger may cold, it automatically starts a Hot/Cold Pack Delay, suspending ignite the dust or fumes. -
Page 12: Storage Recommendations
English Storage Recommendations WALT batteries comply with all applicable shipping regulations as prescribed by industry and legal standards which 1. The best storage place is one that is cool and dry away include UN Recommendations on the Transport of Dangerous from direct sunlight and excess heat or cold. -
Page 13: Intended Use
English These battery packs may be used: DCB181, DCB182, DCB183, Guard release lever DCB183B, DCB184, DCB184B, DCB185, DCB187, DCB189, Battery pack DCB546, DCB547, DCB548, DCB549, DCBP034, DCBP518. Refer to Battery release button Technical Data for more information. Intended Use Package Contents Your cordless angle grinder has been designed for professional cutting, grinding, sanding and wire brush applications. -
Page 14: Assembly And Adjustments
English nOTE: If the gear case and motor housing become separated motor from stalling. The torque limiting clutch has been factory- by more than 3.17 mm, the tool must be serviced and set and cannot be adjusted. re-assembled by a D WALT service center. -
Page 15: Prior To Operation
English The guard release lever should snap into one of the 4. Tighten the clamp nut by hand. Then depress the spindle alignment holes 14 on the guard collar. This ensures that lock button while turning the sanding disc until the sanding the guard is secure. -
Page 16: Operation
English Slider Switch (Fig. A) loose or cracked wires. If power tool or accessory is dropped, inspect for damage or install an undamaged accessory. After CAUTION: Hold the side handle and body of the tool inspecting and installing an accessory, position yourself and firmly to maintain control of the tool at start up and bystanders away from the plane of the rotating accessory during use and until the wheel or accessory stops rotating. - Page 17 English 2. Areas where paint removal is occurring should be sealed with plastic sheeting of 4 mils thickness. 3. Sanding should be done in a manner to reduce tracking of paint dust outside the work area. Cleaning and Disposal 1. All surfaces in the work area should be vacuumed and thoroughly cleaned daily for the duration of the sanding Function Angle...
-
Page 18: Maintenance
English Cutting Metal For cutting with bonded abrasives, always use the Cleaning guard type 1. When cutting, work with moderate feed, adapted to the WARNING: Blow dirt and dust out of the main housing material being cut. Do not exert pressure onto the cutting disc, with dry air as often as dirt is seen collecting in and around tilt or oscillate the machine. -
Page 19: Rechargeable Battery Pack
English according to local provisions. Further information is available at www.2helpU.com. Rechargeable Battery Pack This long life battery pack must be replaced when it fails to produce sufficient power on jobs that were easily done before. At the end of its technical life, discard it with due care for our environment: •... -
Page 20: Accessory Chart
English Accessory Chart guard Type Accessory Description how to Fit grinder Depressed centre grinding disc Type 27 Type 27 guard Guard Flap wheel Backing flange Wire wheels Type 27 depressed centre wheel Locking flange Wire wheels with threaded nut Type 27 guard Wire wheel Wire cup with threaded nut... - Page 21 English Accessory Chart (cont.) guard Type Accessory Description how to Fit grinder Masonry cutting disc, bonded Type 1 Type 1 guard Guard Metal cutting disc, bonded Backing flange Diamond cutting wheels Type 1 Guard Cutting wheel Type 27 Guard Locking flange...
- Page 24 Belgique et WALT - Belgium BVBA Tel: NL 32 15 47 37 63 www.dewalt.be luxembourg België en luxemburg Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 enduser.BE@sBDinc.com 2800 Mechelen Fax: 32 15 47 37 99 Danmark www.dewalt.dk WALT (Stanley Black&Decker AS)