Page 1
ORDER NO.DSD0503040C2 DVD Video Recorder DMR-EH50EB / DMR-EH50EG / DMR-EH50EP / DMR-EH52EG Vol.1 Colour (K).......Black Type (S).......Silver Type SPECIFICATIONS...
Page 4
2005 Matsushita Electric Industrial CO., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law. 1. Safety precautions 1.1. General guidelines 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit.
Page 5
When the exposed metallic part has a return path to the chassis, the reading should be between 1M and 5.2M . / When the exposed metal does not have a return path to the chassis, the reading must be . Figure 1 1.1.2.
Page 6
components. The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge (ESD). 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap, which should be removed for potential shock reasons prior to applying power to the unit under test.
Page 7
an ES device). 3. Precaution of Laser Diode 4. Handling the Lead-free Solder 4.1. About lead free solder (PbF) Distinction of PbF P.C.B.: P.C.B.s (manufactured) using lead free solder will have a PbF stamp on the P.C.B. Caution: - Pb free solder has a higher melting point than standard solder; Typically the melting point is 50 - 70°F (30 - 40°C) higher.
Page 8
- When soldering or unsoldering, please completely remove all of the solder on the pins or solder area, and be sure to heat the soldering points with the Pb free solder until it melts enough. 5. Each Button 6. New Feature 6.1.
Page 9
7. Taking out the Disc from RAM-Drive Unit when the Disc cannot be ejected by OPEN/CLOSE button 7.1. Forcible Disc Eject 7.1.1. When the power can be turned off. 1. Turn off the power and press [STOP] [CH UP] keys on the front panel simultaneously for 5 seconds.
Page 10
7.2. When the Forcible Disc Eject can not be done. 1. Turn off the power and pull out AC cord. 2. Remove the Top Case. 3. Remove the Front Panel. 4. Remove 4 screws and Upper Base Unit from DVD-RAM Drive. 5.
Page 11
8. Service Explorer Confirm “RAM-Drive Last Error” in Service Mode Execute Service Mode 1. Press [REC], [CH UP] and [OPEN/CLOSE] simultaneously for 5 seconds when P-off. FL Display: *After finishing display “(7). Factor of Drive Error occurring”, press [0] [2] ~[1] [9] keys of the Remote Controller so that 19 memories can be displayed as maximum.
Page 12
(5) Error occurring Disc type is displayed for 5 seconds. (6) Disc Maker's ID is displayed for 5 seconds. Example of Disc Maker's ID: DVD-R Disc FL Display (Disc Disc Maker Country Maker's ID) Panasonic Japan Pioneer Japan Mitsubishi Chemical Japan Corporation Japan...
Page 13
ACER Acer Taiwan VIVASTAR VIVASTAR Switzerland LG Electronics Korea DVD-RAM Disc FL Display (Disc Disc Maker Country Maker's ID) Panasonic MATSUSHITA Panasonic Japan Maxell Japan PRODISC Prodisc Taiwan OPTDISC OPTDISC Taiwan Taiwan *Since an display is arbitrarily set up by the disk producer side, the above-mentioned display may be changed.
Page 14
9. Self-Diagnosis and Special Mode Setting 9.1. Self-Diagnosis Functions Self-Diagnosis Function provides information for errors to service personnel by “Self-Diagnosis Display” when any error has occurred. U**, H** and F** are stored in memory and held. You can check latest error code by transmitting [0] [1] of Remote Controller in Service Mode. Automatic Display on FL will be cancelled when the power is turned off or AC input is turned off during self-diagnosis display is ON.
Page 15
Error Diagnosis contents Description Monitor Automatic FL Code Display No error information Initial setting for error code in No display No display memory (Error code Initialization is possible with error code initialization and main unit initialization.) Drive hardware error When drive unit error is detected, No display No display the event is saved in memory.
Page 16
Error Diagnosis contents Description Monitor Automatic FL Code Display Unformatted disc error You have inserted an UNFORMAT unformatted DVD-RAM or DVD- RW that is unformatted or recorded on other equipment. Unit is in termination Unit is in termination process No display PLEASE process now.
Page 17
Item FL display Key operation Mode name Description Front Key Forced disc eject Removing a disc that cannot be The display before When the power ejected. execution leaves. press [STOP] and keys simultaneously The tray will open and unit will seconds.
Page 18
Item FL display Key operation Mode name Description Front Key Aging Perform sequence of modes as * Display following the then When the power Aging Description shown below mode. press [STOP], [POWER] continually. and [OPEN/CLOSE] simultaneously seconds and less seconds. NOTE1: If Unit has not turned Aging mode by...
Page 19
Item FL display Key operation Mode name Description Front Key Demonstration Ejection of the disc is prohibited. *When lock the tray. When the power lock/unlock press [STOP] and The lock setting is effective until [POWER] keys unlocking the tray and not simultaneously released by “Main unit seconds.
Page 20
Item FL display Key operation Mode name Description (Remote controller Release Items Item of Service Mode executing Press [0] [0] or [ is cancelled. service mode. Error Code Last Error Code of U/H/F held by Press [0] [1] in service Display Timer is displayed on FL.
Page 21
Item FL display Key operation Mode name Description (Remote controller RTSC Return in AV1 input signal is encoded (XP), Initial mode: EE2/ Interlace Press [1] [3] in service decoded (XP) and output / XP/ Audio 48kHz mode. decoded signal to external (A &...
Page 22
Item FL display Key operation Mode name Description (Remote controller HDD READ Perform a complete read When the HDD is OK Press [3] [1] in the inspection inspection of the HDD. mode. *When canceling checking mode executing, do “forced If the HDD is defective power-off”.
Page 23
Item FL display Key operation Mode name Description (Remote controller RAM Drive Last RAM Drive error code display. 1. Error Number is Press [4] [2] in service Error displayed for 5 seconds. mode. *For details about the drive error code, refer to the Service Manual When “INFO**** for the specific RAM Drive.
Page 24
Item FL display Key operation Mode name Description (Remote controller Delete the Last Delete the Last Drive Error Press [9] [6] in service Drive Error information stored on the DVD mode. RAM-Drive. Turn on all FL/ All segments of FL and all LEDs All segments are turned Press [5] [1] in service LEDs...
Page 25
Item FL display Key operation Mode name Description (Remote controller Display the Error Display the Error History stored Display reason of error for Press [6] [5] in service History on the unit. 5 seconds. mode. Then press [0] [1] the past 19 error are displayed.
Page 26
Item FL display Key operation Mode name Description (Remote controller AV4(V) / Set input to AV4 (V) and set Press [8] [0] in service AV1(RGB) I/O output to AV1 (RGB) for I/O mode. Setting checking AV2(Y/C) / AV1(V) I Set input to AV2 (Y/C) and set Press [8] [1] in service /O Setting output to AV1 (V) for I/O checking...
Page 27
Item FL display Key operation Mode name Description (Remote controller Initialize Service Last Drive Error, Error history Press [9] [9] in service and Error Codes stored on the mode. unit are initialized to factory setting. Finishing service Release Service Mode. Display in STOP (E-E) Press power button mode...
Page 28
10.3. Top Case 1. Remove the 2 screws (A) and 3 screws (B). 2. Slide Top Case rearward and open the both ends at rear side of the Top Case a little and lift the Top Case in the direction of the arrows.
Page 29
respectively.) 10.5. SD Card P.C.B. 1. Remove 2 Screws (A) to remove SD Card P.C.B. 10.6. Digital P.C.B. 1. Remove 2FFCs and 2 Screws (A). 2. Lift up Digital P.C.B. slightly so to disconnect Connector to remove Digital P.C.B.
Page 30
CAUTION: When replacing Digital P.C.B., pay attention as below. 10.7. DVD-RAM Drive 1. Remove 3 Screws (A) to remove DVD-RAM Drive. 2. Lift up DVD-RAM Drive slightly and remove FFC and remove Cable between DVD-RAM Drive and Main P.C.B.
Page 31
10.8. HDD 1. Remove ATAPI Connector and HDD Power Connector. 2. Remove 4 Screws (A) to remove HDD Angle with HDD.
Page 32
3. Put HDD with HDD Angle up and down inversely so as not to give a shock to HDD. 4. Remove 4 screws to remove HDD.
Page 33
Handling of HDD The following precautions should be taken when handling HDD. 1. Never give an impact to HDD. (Even a drop from 1cm height can be a cause of HDD failure. 2. When placing HDD on a workbench, provide a mat on a bench for shock absorption and anti-static purposes.
Page 34
2. At first disconnect the connector on one side as shown below, and pull out LED P.C.B. 10.10. Power P.C.B. 1. Remove Screw (A). 2. Remove 3 Screws (B) and disconnect Connector (A) and HDD Power Connector. 3. Unlock Power P.C.B. from a Flange to remove Power P.C.B.
Page 35
10.11. Rear Panel 1. Disconnect Fan Connector. 2. Remove 7 Screws (A) and Screw (B). 3. Unlock 2 Locking Tabs (A) to remove Rear Panel.
Page 36
10.11.1. Fan Motor 1. Disconnect Fan Connector and remove 2 Screws (C). 2. Push and unlock 2 locking Tabs (A) to remove Fan Motor. 10.12. Front (L) P.C.B. 1. Remove a Screw (A) to remove Front (L) P.C.B. 10.13. Main P.C.B. 1.
Page 37
3. Remove Power P.C.B. Angle, Digital P.C.B. Angle and SD Card P.C.B. Angle and disconnect Connector (A) to remove Main P.C.B. 10.14. Tuner P.C.B. and Nicam Decoder P.C.B. 1. Pull out the Tuner P.C.B. in the direction of the arrow. 2.
Page 38
Part Number Description Compatibility RFKZ0125 Extension FFC (Digital P.C.B. - DVD-RAM Drive / 40 Pin) Same as E50/ E55 series RFKZ0126 Extension Cable (MainP.C.B. - DVD-RAM Drive/ 4 Pin) Same as E30/HS2 series RFKZ0216 Extension Cable (MainP.C.B. - Power P.C.B. / 23 Pin) Same as E55 series RFKZ0260 Extension Cable (MainP.C.B.
Page 39
12.3. Checking and Repairing of Main P.C.B.
Page 40
12.4. Checking and Repairing of DVD-RAM Drive...
Page 42
13. Caution after replacing parts 13.1. After replacing the RAM Drive with new one 13.2. When the unit does not operate normally after replacing the Timer Microprocessor or Main P.C.B. When the unit does not operate normally after replacing the Timer Microprocessor or Main P.C.B.
Page 43
Turn on the power, and confirm items pointed Items pointed out should reappear. out. Insert RAM disc. The Panasonic RAM disc should be recognized. Enter the EE (TU IN / AV IN - AV OUT) mode. No abnormality should be seen in the picture, sound or operation.
Page 44
Item Contents Check Item Contents Block noise Distorted sound Crosscut noise Noise (static, background noise, etc.) Picture Sound Dot noise The sound level is too low. Picture disruption The sound level is too high. Not bright enough The sound level changes. Too bright Flickering color Color fading...
Page 45
INITIAL/LOGO ABBREVIATIONS A0~UP ADDRESS ACLK AUDIO CLOCK AD0~UP ADDRESS BUS ADATA AUDIO PES PACKET DATA ADDRESS LATCH ENABLE AMUTE AUDIO MUTE AREQ AUDIO PES PACKET REQUEST AUDIO RF SERVO AMP INVERTED INPUT SERVO AMP OUTPUT ASYNC AUDIO WORD DISTINCTION SYNC BIT CLOCK (PCM) BCKIN BIT CLOCK INPUT...
Page 46
INITIAL/LOGO ABBREVIATIONS DACCK D/A CONVERTER CLOCK DEEMP DEEMPHASIS BIT ON/OFF DEMPH DEEMPHASIS SWITCHING DIG0~UP FL DIGIT OUTPUT DATA INPUT DMSRCK DM SERIAL DATA READ CLOCK DMUTE DIGITAL MUTE CONTROL DROP OUT DOUT0~UP DATA OUTPUT DATA SLICE RF (BIAS) DROP OUT SIGNAL DRPOUT DATA REQUEST DREQ...
Page 47
INITIAL/LOGO ABBREVIATIONS IECOUT IEC958 FORMAT DATA OUTPUT IPFRAG INTERPOLATION FLAG IREF I (CURRENT) REFERENCE ISEL INTERFACE MODE SELECT LDON LASER DIODE CONTROL LASER POWER CONTROL LRCK L CH/R CH DISTINCTION CLOCK MA0~UP MEMORY ADDRESS MEMORY CLOCK MCKI MEMORY CLOCK INPUT MCLK MEMORY SERIAL COMMAND CLOCK...
Page 48
INITIAL/LOGO ABBREVIATIONS READ ENABLE RFENV RF ENVELOPE RF PHASE DIFFERENCE OUTPUT (CD-ROM) REGISTER SELECT RSEL RF POLARITY SELECT RESET RESERVE SBI0, 1 SERIAL DATA INPUT SBO0 SERIAL DATA OUTPUT SBT0, 1 SERIAL CLOCK SERIAL DATA CLOCK SCKR AUDIO SERIAL CLOCK RECEIVER SERIAL CLOCK SCLK...
Page 49
SUB CODE Q DATA SYSCLK SYSTEM CLOCK INITIAL/LOGO ABBREVIATIONS TRACKING ERROR TIBAL BALANCE CONTROL BALANCE OUTPUT 1 BALANCE INPUT BALANCE INPUT BALANCE OUTPUT 2 TPSN OP AMP INPUT TPSO OP AMP OUTPUT TPSP OP AMP INVERTED INPUT TRCRS TRACK CROSS SIGNAL TRON TRACKING ON TRSON...
Page 50
INITIAL/LOGO ABBREVIATIONS X' TAL XALE X ADDRESS LATCH ENABLE XAREQ X AUDIO DATA REQUEST XCDROM X CD ROM CHIP SELECT X CHIP SELECT XCSYNC X COMPOSITE SYNC X DATA STROBE XHSYNCO X HORIZONTAL SYNC OUTPUT XHINT XH INTERRUPT REQUEST X' TAL OSCILLATOR INPUT XINT X INTERRUPT X MEMORY WRITE ENABLE...
Page 51
18.6. Tuner Pack Schematic Diagram 18.7. Nicam Decoder Schematic Diagram 18.8. SD Card Schematic Diagram 18.9. LED Schematic Diagram 19. Print Circuit Board 19.1. Power P.C.B. 19.2. Main P.C.B. 19.2.1. Main P.C.B. (1/4 Section) 19.2.2. Main P.C.B. (2/4 Section) 19.2.3. Main P.C.B. (3/4 Section) 19.2.4.
Page 53
21. Replacement Parts List Notes: *Important safety notice: Components identified by mark have special characteristics important for safety. Furthermore, special parts which have purposes of fire-retardant (resistors), high-quality sound (capacitors), low-noise (resistors), etc. are used. When replacing any of components, be sure to use only manufactures specified parts shown in the parts list.
Page 54
Spanish/French, (IC): German, (ID): Swedish/Denish, (IE): English, (IF): Italian/Dutch, (IG): English] *All parts except parts mentioned [SPC] in the Remarks column are supplied from PAVCG. *Parts mentioned [SPC] are supplied from PAVC Ref. No. Part No. Part Name & Description Remarks CASING/ACCESSORY/PACKING VEP01961A...
Page 55
Ref. No. Part No. Part Name & Description Remarks RYP1269C-S FRONT PANEL ASS’Y (EH50EG-S) RYP1269D-S FRONT PANEL ASS’Y (EB) RYP1269G-S FRONT PANEL ASS’Y (EP) RYP1269T-S FRONT PANEL ASS’Y (EH52EG-S) RYP1269C-K FRONT PANEL ASS’Y (EH50EG-K) RYP1269T-K FRONT PANEL ASS’Y (EH52EG-K) 30-1 RGL0678-Q PANEL LIGHT 30-2...
Page 56
Ref. No. Part No. Part Name & Description Remarks RPG7567 PACKING CASE (EP) RPG7648 PACKING CASE (EH52EG-K) RPG7647 PACKING CASE (EH52EG-S) RPN1798 CUSHION RPFD0004 MIRAMAT BAG VEP79107J/H/N MAIN P.C.B. C1501 F1H1E223A029 25V 0.022U C1503 F2A1A2210063 10V 220U C1504 F2A1E1010067 25V 100U C1505 F1J0J106A014 6.3V 10U...
Page 73
X SW+12.4V (FAN MOTOR DRIVE) FAN PWM OUT P7101 P7507 Q7511 88 SD SEL LED (FAN MOTOR DRIVE) SD SEL Q7101 D7101 (SD SEL LED DRIVE) (GREEN) LED P.C.B. FAN MOTOR P7504 P7504 DMR-EH50EB/EG/EP,EH52EG FAN LOCK H Timer Block Diagram...
Page 87
NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. (Main P.C.B.(2/3)) THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST, AND MAY BE DMR-EH50EB/EG/EP,EH52EG A/V I/O Section (Main P.C.B.(2/3)) Schematic Diagram(AI) SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. Schematic Diagram(AI)
Page 88
P.C.B.Name Circuit Name Ref.No. DAT3 Main Net Ref.No.1500,7400 SERIES Audio Net Ref.No.4400,9000 SERIES Main Digital A/V I/O Ref.No.3000,3900,4000,4900 SERIES AVENC/RTSC/AVDEC/MAIN CPU-1 Ref.No.3200,3300 SERIES SBI0 P.C.B. P.C.B. Timer Ref.No.7500,7600 SERIES AVENC/RTSC/AVDEC/MAIN CPU-2 Ref.No.6000,6100,6200 SERIES SD CARD P.C.B. DMR-EH50EB/EG/EP,EH52EG Interconnection Schematic Diagram...
Page 89
(SD SEL LED DRIVE) (DVD SEL LED DRIVE) (HDD SEL LED DRIVE) R7108 R7110 R7112 NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST. DMR-EH50EB/EG/EP,EH52EG LED Schematic Diagram...
Page 90
R1515 K9ZZ00001279 X SW 3.3V ZJ7407 K9ZZ00001279 ANA+3.3V ANA+3.3V D+3.3V D+3.3V DMR-EH50EB/EG/EP,EH52EG IMPORTANT SAFETY NOTICE: COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS Main Net Section(Main P.C.B.(1/3)) FOR SAFETY.WHEN REPLACING ANY OF THESE COMPONENTS.ONLY THE SAME TYPE. Schematic Diagram(M)
Page 91
WIDE 0.022 QR7404 ANA+3.3V R1508 UNR521500L D+3.3V DMR-EH50EB/EG/EP,EH52EG DMR-EH50EB/EG/EP,EH52EG C1506 10V47 NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR Main Net Section(Main P.C.B.(1/3)) Main Net Section(Main P.C.B.(1/3)) ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST.
Page 92
R7319 TL7301 R7314 C7313 C7312 LB7302 16V10 16V10 J0JCC0000124 C7318 16V10 R7315 C7314 DMR-EH50EB/EG/EP,EH52EG NOTE: Nicam Decoder DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM Schematic Diagram FOR ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST.
Page 93
THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. COLD IMPORTANT SAFETY NOTICE: COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS FOR SAFETY.WHEN REPLACING ANY OF THESE COMPONENTS.ONLY THE SAME TYPE. DMR-EH50EB/EG/EP,EH52EG Power Supply Schematic Diagram...
Page 95
C6801 0.01 XSORX TL6803 RX6802 RX6801 12KX4 22X4 CKF12 CKF13 R6802 22 R6803 22 NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST. DMR-EH50EB/EG/EP,EH52EG SD Card Schematic Diagram...
Page 96
R7574 22K FAN MOTOR C7533 6V47 C7587 1 C7547 1 R7627 30K R7624 10K LB7509 J0JCC0000060 X SW+12.4V C7590 R7625 FAN GND R7626 820 R7577 10K M:Main Net Section(Page: AI:A/V I/O Section(Page: DMR-EH50EB/EG/EP,EH52EG T:Timer Section(Page: Timer Section(Main P.C.B.(3/3)) Schematic Diagram(T)
Page 97
(POWER SAVE :ON) (SW. :OFF) D7504 MAZ4300NLF UNREG 38V DMR-EH50EB/EG/EP,EH52EG DMR-EH50EB/EG/EP,EH52EG IMPORTANT SAFETY NOTICE: NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR Timer Section(Main P.C.B.(3/3)) COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST.
Page 98
B1GBCFJA0002 (AUDIO MUTE) EH50EB/EG,EH52EG K7809 0 DMR-EH50EB/EG/EP,EH52EG NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. Tuner Pack THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST, AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 99
18 Schematic Diagram 18.1. Interconnection Schematic Diagram POWER P7001 P7506 P1502 DR12V DR12V POWER SW ON POWER SW ON DRGND DR5V FRONT(L) P.C.B. P7402 P1101 XINTP P1102 P1501 PP7401 PS7801 SCLK UARTM2P X SW 5.8V X SW 5.8V BOOSTER5V BOOSTER 5V XINTM X SW 5.8V X SW 5.8V...
Page 100
D1.5V D 1.5V 3.3V CPNCIN DM CPNCIN DM SBO0 D1.5V D 1.5V DAT2 DAT0 XDIAG DAT1 P.C.B.Name Circuit Name Ref.No. DAT3 Audio Net Ref.No.4400,9000 SERIES Digital AVENC/RTSC/AVDEC/MAIN CPU-1 Ref.No.3200,3300 SERIES SBI0 P.C.B. AVENC/RTSC/AVDEC/MAIN CPU-2 Ref.No.6000,6100,6200 SERIES DMR-EH50EB/EG/EP,EH52EG Interconnection Schematic Diagram...
Page 105
18.3. Main Net Section (Main P.C.B. (1/3)) Schematic Diagram (M) TO P1102 POWER P.C.B. TO P9001 P1501 DIGITAL P.C.B. (Audio Net Section) P7402 X SW 5.8V X SW 5.8V X SW 12.4V X SW 12.4V XINTP XINTP SCLK G SCLK A UARTM2P G UARTM2P A XINTM...
Page 108
AV2 PB R1507 1500 C1501 WIDE 0.022 QR7404 R1508 UNR521500L DMR-EH50EB/EG/EP,EH52EG C1506 10V47 NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR Main Net Section(Main P.C.B.(1/3)) ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST. Schematic Diagram(M)
Page 109
18.4. A/V I/O Section (Main P.C.B. (2/3)) Schematic Diagram (AI) S VIDEO VIDEO AUDIO IN L G AADC L A G AADC R A G CIN DM A G V YIN DM A G SLICER A G IIC CLK A G IIC DATA A V SYNC DET GND GND...
Page 111
ENC G/Y IN AV1 FB OUT VGND AV1 V IN C3030 50V4.7 ENC B/B-Y IN AV2 FB IN C3031 0.01 REG2.5 AV2 V/Y IN C3013 25V47:EH50EB 10V100:EH50EG/EP, EH52EG C3014 C3034 C3035 0.01 6V100 DMR-EH50EB/EG/EP,EH52EG A/V I/O Section (Main P.C.B.(2/3)) Schematic Diagram...
Page 112
BOOSTER+5V LB3002 J0JGC0000020 C3033 C3032 0.01 6V100 DMR-EH50EB/EG/EP,EH52EG A/V I/O Section NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. (Main P.C.B.(2/3)) THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST, AND MAY BE ematic Diagram(AI) SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 113
18.5. Timer Section (Main P.C.B. (3/3)) Schematic Diagram (T) D7509 B0JDCE000002 X SW 5.2V C7585 6V100 TW7501 5.2V TO P7101 LED P.C.B. P7507 IC7505 IC7506 R7629 6800 C0EBJ0000336 C0EBE0000457 HDD SEL LED R7630 6800 DVD SEL LED (RESET) (RESET) R7631 6800 SD SEL LED OUT VDD GND...
Page 114
FAN PWM OUT2 IIC CLK AV2 PB L IIC DATA WIDE H R7652 100 K7504 0 R7628 X SW+12.4V R7576 C7534 0.01 R7563 R7574 22K C7533 6V47 C7547 1 LB7509 J0JCC0000060 X SW+12.4V R7577 10K DMR-EH50EB/EG/EP,EH52EG Timer Section(Main P.C.B.(3/3)) Schematic Diagram(T)
Page 115
C7571 R7616 50V22 C7569 R7614 2200P QR7508 Q7510 UNR521400L 2SD1994BR1VT (POWER SAVE :ON) (SW. :OFF) D7504 MAZ4300NLF DMR-EH50EB/EG/EP,EH52EG IMPORTANT SAFETY NOTICE: COMPONENTS IDENTIFIED WITH THE MARK HAVE TH Timer Section(Main P.C.B.(3/3)) Schematic Diagram(T) FOR SAFETY.WHEN REPLACING ANY OF THESE COMPO...
Page 116
R7502 C7502 3900 TL7502 100P UNREG 38V DMR-EH50EB/EG/EP,EH52EG NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR Timer Section(Main P.C.B.(3/3)) THE MARK HAVE THE SPECIAL CHARACTERISTICS ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST. Schematic Diagram(T)
Page 118
(VIDEO BUFFER) R7844 EH50EB/EG,EH52EG K7809 0 DMR-EH50EB/EG/EP,EH52EG NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. Tuner Pack THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST, AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 119
18.7. Nicam Decoder Schematic Diagram C7335 IC7302 C0EAH0000051 TO PK7701 (RESET) MAIN P.C.B. (MAIN NET SEC.) PK7301 TU AUDIO IN LB7303 J0JCC0000080 L7303 1u JC REG.5V C7303 C7305 C7306 C7334 R7304 6V100 6V100 0.01 50V2.2 C7311 100P C7301 R7301 C7302 0 TO PK7702 MAIN P.C.B.
Page 120
TL7303 TL7301 R7314 C7313 C7312 16V10 16V10 LB7302 J0JCC0000124 C7318 16V10 R7315 C7314 DMR-EH50EB/EG/EP,EH52EG NOTE: Nicam Decoder DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM Schematic Diagram FOR ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST.
Page 122
R6807 DAT0 DAT1 DAT2 C6801 0.01 RX6802 RX6801 12KX4 22X4 R6802 22 R6803 22 NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST. DMR-EH50EB/EG/EP,EH52EG SD Card Schematic Diagram...
Page 123
18.9. LED Schematic Diagram TO P7507 MAIN P.C.B. (TIMER SECTION) P7101 X SW 5.2V SD SEL LED DVD SEL LED HDD SEL LED R7103 SD SEL D7101 B3ABA0000595 Q7101 2SD0601ARN (SD SEL LED DRIVE) R7108...
Page 124
0.01 Q7102 Q7103 2SD0601ARN 2SD0601ARN (DVD SEL LED DRIVE) (HDD SEL LED DRIVE) R7110 R7112 NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST. DMR-EH50EB/EG/EP,EH52EG LED Schematic Diagram...
Page 125
Ref No. Q7102 Q7103 Q7101 MODE PLAY STOP...
Page 126
IC1501 IC1502 Ref No. MODE PLAY STOP Ref No. IC1504 IC1505 MODE PLAY STOP IC1510 IC1511 Ref No. MODE PLAY STOP Ref No. IC3001 MODE PLAY STOP IC3001 Ref No. MODE PLAY STOP IC3001 Ref No. MODE 11.6 PLAY 11.6 STOP 11.6 IC3001...
Page 133
:REC SIGNAL :PB SIGNAL JK3001 REAR JACK D4005 Q4006 MIX L OUT2 MUTE LINE OUT FROM XTMUTE QR4002-QR4005 TIMER Q4007 IC7501- 63 Q4004 SECTION MIX R OUT2 MUTE MUTE LINE OUT D4006 Q4009 CIRCUIT MUTE FROM XDMUTE DIGITAL Q4008 IC4408- 4 P.C.B.
Page 134
(DECODER/EXT) AV2 B Q7802 TUNER BLUE AV2 G PP7401 PS7801 VIDEO CLAMP CLAMP BUFFER AV2 V/Y VIDEO/Y EH50EB/EG,EH52EG 2.3V K7809 AV2 B CLAMP 1.0V PP7401 PS7801 VIDEO AV2 V/Y EH50EB CLAMP TUNER P.C.B. DMR-EH50EB/EG/EP,EH52EG Analog Video Block Diagram AV2 R/G/B...