Page 2
2000 Matsushita Electric Industrial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law. 1. INTRODUCTION This service manual contains technical information which will allow service personnel to understand and service this model. If the circuit is changed or modified, this information will be followed by supplementary service manual to be filed with original service manual.
Model No. FJ604EG-K FJ606EG-K FJ610EG-S/ FJ606EGYK FJ610EGYS/ FJ610B-S/K FJ611B Indication Mark Model No. FJ604ECMK FJ606EC-K FJ606ECMK FJ610EC-S/ FJ610ECMS FJ610ECYS/ FJ610BL Indication Mark Model No. FJ603EL-K FJ603EP-K FJ603EPYK Indication Mark 2. GENERAL DESCRIPTIONS 2.1. SERVICE INFORMATION 2.1.1. CHANNEL MEMORY IC INITIALIZATION When replacing the Memory IC7704 and/or Oscillator X6001, Memory IC7704 has to be initialized due to the setting value changes.
Page 4
PROCEDURES FIP Display Monitor Screen Press the FF and EJECT keys simultaneously for 3 None seconds. Press the FF and EJECT keys simultaneously more None twice. Press the EJECT key for 3 seconds. None Press the CH UP key twice. None Press the POWER key.
Page 5
the Remote Controller. Model No. Suffix Model Option Option Option Code Code Code Code NV-FJ603 EL-K NV-FJ603 EP-K/EPYK NV-FJ604 ECMK NV-FJ604 EG-K (To be continued on next page.) Model No. Suffix Model Option Option Option Code Code Code Code NV-FJ606 EC-K/ECMK NV-FJ606 EG-K/EGYK...
NOTE 1. If the VCR is turned on with the antenna not connected, all channels are skipped. Therefore, firmly connect the antenna and then turn the VCR off and on again to execute Auto tuning. 2. When Auto Tuning is canceled halfway, Auto Tuning is not executed even if the VCR is turned off and then turned on again.
2.1.4. REMOVAL OF CASSETTE TAPE There are 2 ways to remove a cassette tape. 1. Removal of compulsory loading. A. Press FF and EJECT buttons simultaneously and set the Service Mode 7. B. Press STOP button in order to unload the mechanism. (Pay an attention of tape slack) Service Mode Indication: 7 ** ** (STOP)
D. Rotate Main Cam Gear to the clockwise in order to eject the cassette tape. 2.1.5. CYLINDER UNIT REPLACEMENT 1. CYLINDER UNIT REPLACEMENT A. Remove the Mechanism unit from MAIN C.B.A./Chassis by referring “SECTION 2.Disassembly Procedure”. B. Remove the 3 screws (A) of the CYLINDER UNIT with a screw driver.
Page 9
D. Remove the Cylinder Rotor Unit. E. Loose Hex screw (C) (1.5 mm) and remove the CYLINDER RETAINER. F. Remove the Upper Cylinder. Fig. S7 3. UPPER CYLINDER ASSEMBLY When reassembling, perform the steps in the reverse order. Notes : A.
Page 10
of the Cylinder Retainer. Fig. S8 C. Install the Cylinder Rotor Unit so that the inner hole of the Cylinder Rotor Unit fits to the small projection (D) on top of the Upper Cylinder. D. Tighten 2 screws (B). Fig. S9 E.
2.3. OPERATING INSTRUCTIONS (NV-FJ604/606/610 Series) 2.4. INTRODUCTION OF VIDEO HEAD CLEANING CASSETTE (POLISHING TYPE) 1. We are pleased to introduce Panasonic Video Head Cleaning Cassette, VFK0923FT [for service purposes] and VFK0923FSE [ for end users] for all VHS/SVHS VCP and VCR.
2.5. Caution for AC Mains Lead (NV-FJ610B/BL, NV-FJ611B) 3. ADJUSTMENT PROCEDURES 3.1. DISASSEMBLY METHOD 3.1.1. DISASSEMBLY FLOW CHART This flow chart indicates disassembly steps of the cabinet parts and the circuit boards in order to find the necessary items for servicing. When reassembling, perform the steps in the reverse order.
3.1.2. DETAIL OF DISASSEMBLY METHOD 1. REMOVAL OF THE TOP PANEL Remove 4 Screws (A) Fig. D2...
Page 14
2. REMOVAL OF THE FRONT PANEL UNIT Unlock 7 Tabs (B) Fig. D3 3. REMOVAL OF THE CYLINDER STATOR C.B.A. Remove 2 Screws (C) Disconnect Flat Card Cable (D) Fig. D4...
Page 15
4. REMOVAL OF THE POWER C.B.A. Disconnect Bridge Connector (E) Unlock 6 Tabs (F) Fig. D5 COUTIONS: Please pay an attention to disconnect the connector (P1001- P1103) which connected between Main C.B.A. and Power supply unit as shown below. Fig. D6...
As above drawing, disconnect the connector by SCREW DRIVER from the direction (A). / Do not disconnect from direction (B) because it is possibility to damage the parts located by the connector. / 5. REMOVAL OF THE MECHANISM UNIT Remove 3 Screws (G) Remove 2 Screws (H)
8. SERVICING POSITION Fig. D10 3.2. MECHANICAL ADJUSTMENT PROCEDURES Refer to the Service Manual for Z-Mechanism Chassis. / (Order No. VRD9802005C2) 3.3. ELECTRICAL ADJUSTMENT PROCEDURES 3.3.1. TEST EQUIPMENT The following equipments are required for Electrical Adjustments. 1. Dual-Trace Oscilloscope - Voltage Range: 0.005-5V/div - Frequency Range: DC-35MHz - Probes: 10:1 / 1:1 2.
5. Video Sweep Generator 6. Sinewave Generator 7. Video Pattern Generator 8. Monitor TV 9. DC Power Supply 10. VHS Blank Tape 11. VHS Alignment Tape - Parts No.: VFJ8125H3F(PAL) 3.3.2. VCR SETTING When no indication in the procedure, set each selector as follows. 1.
3.3.5. AI FUNCTION ADJUSTMENT / (AUTOMATIC) PROCEDURES FIP Display Press the FF and EJECT buttons simultaneously for 3 seconds. Press the FF and EJECT buttons simultaneously twice. Press the EJECT key for 3 seconds. Press the CH UP key 3 times. Insert the Blank Tape.
PROCEDURES FIP Display Set the Video Sweep signal (See Fig.E1) Make the self-recording tape. Press the FF and EJECT Buttons simultaneously for 3 seconds. Press the FF and EJECT Buttons simultaneously twice. Press the EJECT key for 3 seconds. Press the CH UP and/or CH DOWN key until "11"...
NOTE: THIS TABLE IS ONLY FOR “B-S/B-K/BL-K” MODEL 6. BLOCK DIAGRAMS 6.1. SYSTEM CONTROL & SERVO /TIMER SECTION BLOCK DIAGRAM 6.2. VIDEO SECTION BLOCK DIAGRAM 6.3. Hi-Fi AUDIO SECTION BLOCK DIAGRAM 6.4. INPUT/OUTPUT SECTION BLOCK DIAGRAM 7. SCHEMATIC DIAGRAMS 7.1. POWER SCHEMATIC DIAGRAM 7.2.
7.3. VIDEO SECTION IN MAIN SCHEMATIC DIAGRAM 7.4. Hi-Fi AUDIO SECTION IN MAIN SCHEMATIC DIAGRAM 7.5. INPUT/OUTPUT & TUNER SECTION IN MAIN SCHEMATIC DIAGRAM 7.6. CYLINDER MOTOR UNIT SCHEMATIC DIAGRAM 7.7. OSD SECTION IN MAIN SCHEMATIC DIAGRAM 7.8. TV DEMODULATOR PACK SCHEMATIC DIAGRAM 7.9.
10.1. MECHANICAL REPLACEMENT PARTS LIST 10.1.1. CHASSIS PARTS SECTION Ref. No. Part No. Part Name & Description Remarks 1 (1) VEG1535 CYLINDER UNIT [SUPPLIED FROM MBV] 2 (1) VEH0844 UPPER CYLINDER UNIT 3 (1) VDB1256 CYLINDER RETAINER 4 (1) VEK8840 CYLINDER STATOR UNIT [SUPPLIED FROM MBV]...
Page 43
Ref. No. Part No. Part Name & Description Remarks 51 (1) VXP2035 CENTRE CLUTCH UNIT 60 (1) VMA9516 TOP PLATE 61 (1) VMB3047 CONNECTION SPRING 62 (1) VMD3379 SIDE PLATE (L) [SUPPLIED FROM MBV] 63 (1) VXA6607 SIDE PLATE (R) UNIT 64 (1) VXA5746 CASSETTE HOLDER UNIT...
Page 44
Ref. No. Part No. Part Name & Description Remarks 101 (2) VGM1466 TOP PANEL [SUPPLIED FROM MBV] NV-FJ610EG-K/ EGYK/B-K NV-FJ610ECMK/ EC-K/ECYK NV-FJ611B-K NV-FJ606EG-K/ EGYK NV-FJ606ECMK/ EC-K NV-FJ603EPYK/ EL-K/EP-K NV-FJ604EG-K/ ECMK 101 (2) VGM1556 TOP PANEL [SUPPLIED FROM MBV] NV-FJ610EG-S/ EGYS/B-S NV-FJ610ECMS/ EC-S/ECYS NV-FJ610BL-S...
Page 45
Ref. No. Part No. Part Name & Description Remarks 102 (2) VYP7546 FRONT PANEL UNIT [SUPPLIED FROM MBV] NV-FJ603EL-K 102 (2) VYP7548 FRONT PANEL UNIT [SUPPLIED FROM MBV] NV-FJ611B-K 102 (2) VYP7550 FRONT PANEL UNIT [SUPPLIED FROM MBV] NV-FJ604EG-K/ ECMK...
Page 46
Ref. No. Part No. Part Name & Description Remarks 201 (3) VQT8539 OPERATING INSTRUCTIONS [SUPPLIED FROM MBV] (ENGLISH) NV-FJ610EGYK/ EGYS NV-FJ610ECYK/ ECYS NV-FJ606EGYK 201 (3) VQT8540 OPERATING INSTRUCTIONS [SUPPLIED FROM MBV] (GERMAN) NV-FJ610EG-K/ EG-S/EGYK NV-FJ610EGYS/ ECMK/ECMS NV-FJ606EG-K/ EGYK/ECMK NV-FJ604EG-K/ ECMK 201 (3) VQT8541 OPERATING INSTRUCTIONS...
Ref. No. Part No. Part Name & Description Remarks 212 (3) VPN5341 CUSHION (R) [SUPPLIED FROM MBV] 213 (3) VPG0C84 PACKING CASE [SUPPLIED FROM MBV] NV-FJ611B-K 213 (3) VPG0C83 PACKING CASE [SUPPLIED FROM MBV] NV-FJ610EG-K/ EGYK/B-K NV-FJ610ECMK/ EC-K/ECYK 213 (3) VPG0C82 PACKING CASE [SUPPLIED...
Page 50
Ref. No. Part No. Part Name & Description VEP06D25A MAIN C.B.A. VEP06D25B MAIN C.B.A. VEP06D25C MAIN C.B.A. VEP06D25D MAIN C.B.A. VEP06D57A MAIN C.B.A.
Page 51
Ref. No. Part No. Part Name & Description VEP06D57B MAIN C.B.A. VEP07A16A DECODER PACK C.B.A. VEP07A18A NICAM DECODER PACK C.B.A. VEP07A18B NICAM DECODER PACK C.B.A. VEP07A23A TV DEMODULATOR PACK C.B.A VEP07A23B TV DEMODULATOR PACK C.B.A VEP07A31C TV DEMODULATOR PACK C.B.A...
Page 52
Ref. No. Part No. Part Name & Description VEP01826T POWER C.B.A. ------------ CYLINDER STATOR C.B.A. ------------ CAPSTAN DRIVE C.B.A. TU7601 ENG47307G1 TUNER TU7601 ENG47308G1 TUNER TU7601 ENG47309G1 TUNER TU7601 ENG47306G1 TUNER F1101 XBA2C16TH15 FUSE VEP06D25A MAIN C.B.A.
Page 136
Ref. No. Part No. Part Name & Description VMP4471 TV DEMODULATOR ANGLE VEP01826T POWER C.B.A. C1101 VCK0286E102 CERAMIC CAPACITOR C1102 ECQV1H104JM P.CAPACITOR 50V 0.1U C1103,04 VCK0286E102 CERAMIC CAPACITOR C1106 ECQE6104KF P.CAPACITOR 630V 0.1U C1108 ECCD3A470KGE C.CAPACITOR 1KV 47P C1109 ECKD2H103PU C.CAPACITOR 500V 0.01U C1110 ECEA0JGE331...
Page 137
Ref. No. Part No. Part Name & Description IC1102 UPC1093J IP1101 VSF0015A10 FUSE L1107 ELF15N005A LINE FILTER L1108 ELF17N004A LINE FILTER L1121,22 VLQ0655K220 COIL 22UH L1123,24 ELESE101KA COIL 100UH LB1105 VLP0056 FERRITE BEAD P1101 VJS3306 AC INLET P1103 VJP3917A016G CONNECTOR (MALE) 16P Q1111 CNX82A5387 PHOTO COUPLER...
Page 138
Ref. No. Part No. Part Name & Description VJS3537B009G CONNECTOR (FEMALE) 9P...
Page 139
A :TO AUDIO SECTION VIDEO MAIN SIGNAL PATH IN REC MODE AUDIO MAIN SIGNAL PATH IN REC MODE VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE AUDIO MAIN SIGNAL PATH IN PLAYBACK MODE S :TO SYSTEM CONTROL & SERVO / TIMER SECTION I :TO INPUT/OUTPUT &...
Page 140
VIDEO SECTION IN MAIN WAVEFORM CHART (SP MODE) IC3001-7,8 PLAY IC3001-15 PLAY IC3001-20 PLAY IC3001-30 PLAY/REC IC3001-31 PLAY/REC IC3001-37 PLAY 50mVp-p (0.2msec. div) 250mVp-p (20 sec. div) 150mVp-p (2msec. div) 300mVp-p (2msec. div) 300mVp-p (2msec. div) 5.5Vp-p (5msec. div) IC3001-38 PLAY IC3001-42,43 PLAY IC3001-52 PLAY IC3001-78 PLAY...
If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local Panasonic Dealer. IF THE FITTED MOULDED PLUG IS UNSUITABLE TYPE B FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY.
Page 142
AUDIO MAIN SIGNAL PATH IN PLAYBACK MODE : TO INPUT/OUTPUT & TUNER SECTION : TO VIDEO SECTION : TO SYSTEM CONTROL & SERVO SECTION AUDIO MAIN SIGNAL PATH IN REC MODE (A1) (A2) (A3) (A4) (A5) (A1) RF C OUT 2 (A2) AUDIO 1 IN(R) (A3)
Page 143
AUDIO MAIN SIGNAL PATH IN PLAYBACK MODE FM REC MUTE L QR4506 AUDIO MAIN SIGNAL PATH IN REC MODE FROM A H SW SYSTEM CONTROL & SERVO SECTION IIC CLK IIC DATA DECODER (R) FROM IC4001 INPUT/ OUTPUT DECODER (L) SECTION AUDIO 2 IN (L) AUDIO 2 IN (R)
Page 144
VIDEO MAIN SIGNAL PATH IN REC MODE VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE TUNER TU7601 TO VIDEO TUN V IN VIDEO OUT SECTION FROM VIDEO IN V OUT TO I/O SYSTEM CONTROL & SERVO IC4901 SECTION Q4901 JK4902 (TV) <...
Page 145
VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE CAPSTAN SERVO PHASE LOOP CYLINDER SERVO PHASE LOOP DP7501 VIDEO MAIN SIGNAL PATH IN REC MODE CAPSTAN SERVO SPEED LOOP CYLINDER SERVO SPEED LOOP IC6001 SYSTEM CONTROL/SERVO IC IC7501 TIMER IC TIMER DISPLAY S1501 MODE SW POS.
Page 146
VIDEO MAIN SIGNAL PATH IN REC MODE VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE IC3501 P3502 P3502 LP L' (49 m) P3502 SP R(26 m) A L (33 m) TW3030 P3502 A R (33 m) Q3003 SP L(26 m) X3001 4.433619MHz LP R'(49 m) P3502...
CYLINDER MOTOR UNIT Integrated Circuit HALL IC Connector P2901 ADDRESS INFORMATION HALL IC P2901...
Page 152
F1101 R1111 R1107 R1102 CAUTION MARK INDICATES THE PRIMARY CIRCUIT TO DISTINGUISH THE PRIMARY FROM THE SECONDARY CIRCUIT. PAY ATTENTION NOT TO RECEIVE AN ELECTRIC SHOCK DURING REPAIR AND SERVICE OF THE PRODUCTS. C1138 IMPORTANT SAFETY NOTICE: COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS FOR SAFETY.
Page 153
R0206 (FG HEAD) R0212 R0213 Q0203 P0201 Q0202 IC0201 R0207 (CAPSTAN MOTOR DRIVE) HOLE HOLE SENSOR SENSOR R / F RCC SET Q0201 GND(FG) C0201 R0210 GND(MOTOR) D0203 TL0204 TL0202 TL0203 OUT 2 OUT 1 TL0201 PS 14V L0201 R0208 R IN C0208 HOLE...
Page 156
VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE VIDEO MAIN SIGNAL PATH IN REC MODE AUDIO MAIN SIGNAL PATH IN PLAYBACK MODE AUDIO MAIN SIGNAL PATH IN REC MODE C4906 R4924 LB4903 470P TW3002 VIDEO JK4902-1,3 PLAY R4927 250mVp-p (0.5msec. div) A :TO AUDIO SECTION LB4904 JK4901...
Page 157
PROG(H) IIC DATA 0 IIC CLK 0 N SW 5V V OUT TO I/O PS 5V AUDIO DEF(H) PS 36V AFC S IIC DATAS IIC CLKS C4935 LB7601 2200P TU7601 ENG47307G1:(A,D,G,H) VEK8959:(B,E,J) C7601 C7602 ENG47308G1:(C) 6V100 220P ENG47309G1:(F) L7601 B(+)B C7613 R7602 3.0 (3.4)
Page 158
CYLINDER SERVO SPEED LOOP P2901 MAIN COIL 2 MAIN COIL 3 HALL IC GND(CYL) MAIN COIL 1 NOTE: DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST.
Controls and Components Keep this page open as you read through the Operating Instructions. Refer to it for the control and component names and numbers which appear in the text. °Z ∏ Í < EJECT TIMER RECÁ ¥REC/OTR °] °[ AV2 ( DECODER/EXT ) AV1 ( TV ) AUDIO OUT...
Preparing the Remote Control VCR Operation Inserting Remote Control Batteries When you want to operate the VCR, set the VCR/TV switch N to “VCR”. 1 Slide off the battery cover. °2 Numeric buttons To select the programme positions (1–99) of the VCR. Example: 2 Insert the batteries with the To enter a ShowView number.
Warning and Important Information As this equipment gets hot during use, operate it in a well ventilated place; do not install this equipment in a confined space such as a book case or similar unit. IMPORTANT Your attention is drawn to the fact that the recording of pre-recorded tapes or discs or other published or broadcast material may infringe copyright laws.
AV Input on Your Panasonic TV The settings for operating the TV with the remote control Your Panasonic TV uses one of three different methods for have already been made. switching between TV reception and the AV input(s). Perform No additional settings need to be performed.
Connecting the VCR to a TV If you are connecting your VCR to a TV using RF coaxial cable and 21-pin Scart cable, then Method 1. follow the steps below. (AV Connection) Aerial (not supplied) Aerial lead (not supplied) TV (not supplied) Aerial Input AC Input socket...
If you are connecting your VCR to a TV using Method 1, Hint: follow the operations explained below. ≥ If you select “Schweiz”, “Suisse” or “Svizzera” on the Country setting menu, the Functions setting menu appears Auto Setup Function automatically to let you set the item “Power save” to “ON”. In this setting, the VCR’s power consumption is minimised The Auto Setup function automatically tunes all available TV when it is off (Standby mode).
Page 166
Tuned Correctly by the Auto Setup Select an unoccupied programme position (which is Function not tuned to a TV station). If you are using a Panasonic TV, select programme See page 8. position “0”. Set the VCR/TV switch N to “VCR”.
Page 167
Playback Notes: Preparations ≥ Cue, review or slow playback will be automatically ≥ Confirm that the VCR is on. cancelled after 10 minutes, and still playback after 5 ≥ Confirm that the TV is on and the VCR viewing channel is minutes.
Page 168
Recording To Stop Playback Automatically Preparations (Playback Off Timer Function) ≥ Confirm that the VCR is on. If you set the playback duration, the playback will stop ≥ Confirm that the TV is on and the VCR viewing channel is automatically.
To Display the Approximate Remaining To Perform an OTR Recording: Display the VCR picture on the TV. Tape Time The remaining tape time can be displayed in the VCR Insert a video cassette with an intact erasure prevention display. tab. Press the TAPE button B and select the corresponding cassette tape length.
Timer Recording This function lets you programme the VCR for unattended automatic recording of desired TV programmes when you are not at home or sleeping. Press the SP/LP button D to set the desired tape You can programme timer recordings in two different ways: speed.
To Programme with the ShowView Function Press the TIMER REC button C to switch the VCR over to the timer recording standby mode. The ShowView numbers assigned to each TV programme ≥ Check that “Á” is lit on the VCR display. and published alongside the TV programme listings in If it is flashing, check the timer recording details again.
Other Timer Recordings and Convenient Functions Setting the Recording Date/Day(s) Condition for correct operation of the Auto SP/LP Change function: Perform this operation in operation step 3 when ≥ The tape length of the inserted cassette must be set programming a timer recording with the On Screen Display, correctly.
Page 173
To Change a Timer Recording To Check the Total Timer Recording Programming Programming Time jjjjj jj/jj jjjjj jj/jj jjjjj jj/jj It is not possible to change a programming while the timer The total time indication for timer jjjjj jj/jj jjjjj jj/jj recording is being performed.
Search Functions To Quickly Find the Beginning To Search for a Desired of a Desired Programme Programme While Checking the (VISS=VHS Index Search Recorded Contents on a System) Cassette (Intro-Jet Scan) This VCR automatically records special index signals on the This VCR automatically records special index signals on the tape every time a recording is started.
Editing Assemble Editing The assemble editing function makes it easy to record the picture and sound of virtually any number of scenes or When that point is reached, press the Pause/Slow programmes in succession. button 7 again to start recording the new picture and Assemble editing from an external source, for example from sound from the playback unit.
Connecting the VCR to a Decoder/ Connecting the VCR to a Stereo Amplifier ≥ When you start playback on the VCR, the TV is To connect this VCR to a decoder or a stereo amplifier, make automatically switched to the VCR mode. However, during the connections shown in the illustration below.
Connecting the VCR to a Satellite Receiver or Digital Receiver Satellite receiver here includes a digital receiver. If the Satellite Receiver Is Not Equipped with a 21-Pin Scart Socket The connection method differs depending on the type of your In case your satellite receiver is not equipped with a 21-pin satellite receiver.
Tuning and Assigning the TV Stations Available in Your Area to the Programme Positions (Manual Tuning) This VCR has 99 programme positions that can be preset to To Enter or Change the Name of a TV receive TV stations. Station Usually, if you switch the VCR on for the first time after making the necessary connections, the VCR will start the Auto Setup function automatically so that all available TV...
Page 179
To Obtain the Best Tuning Condition To Enter Newly Available TV Stations Press the MENU button S to display the Main menu on Press the MENU button S to display the Main menu on the TV screen. the TV screen. Press the Cursor buttons (34) P to select “Tuning”...
Page 180
To Change the Type of Video System To Facilitate the Following Operations with (Colour TV system) the Instruction Indications on the On Screen Display Press the MENU button S to display the Main menu on ≥ To delete a programme position the TV screen.
Restarting the Auto Setup/ Resetting the VCR to the Shipping Condition Performing Auto Setup automatically tunes all TV stations available in your area for the VCR. Restarting this function is convenient when you move to another area and may need to set up the VCR again. To Restart the Auto Setup To perform the Auto Setup again, follow the operation steps below.
Setting the VCR’s Clock Usually, the VCR’s Auto Setup function automatically adjusts To Activate the Automatic Time Correction the clock to the correct time. Function Under some reception conditions, however, the VCR cannot set the clock automatically. If a TV station transmits a signal for time setting, performing In this case, follow the operation steps below to manually set the operation steps below activates the Automatic time the clock.
Other Convenient Functions (Various Settings) For Automatic Display on the TV Screen of 5 Tape length indicator At each press of the TAPE button B, the selected tape the TV Station Information, etc. length is indicated. Press the MENU button S to display the Main menu For E30, -60, -90, -120 and -180 tapes 2E-180: on the TV screen.
Page 184
For Reduced the VCR’s Power For Automatic Change of the Brightness Consumption When the VCR Is Switched of the VCR Display When the VCR Is Switched Off Press the MENU button S to display the Main menu on Press the MENU button S to display the Main menu the TV screen.
To Set the Colour TV System Used During Country Setting Playback or Recording from an External Press the MENU button S to display the Main menu Source on the TV screen. Press the MENU button S to display the Main menu Press the Cursor buttons (34) on the TV screen.
Page 186
Glossary Changes in VPS (Video Programme System)/ Programming Non- ShowView ShowView method ShowView program- PDC (Programme Delivery Control) program- program- ming The Video Programme System (VPS) or the Programme ming start ming Delivery Control (PDC) is a very convenient system which Selected time assures that the TV programmes you have programmed for...
Page 187
Crystal View Control (CVC) The crystal view control function ensures that you always obtain the optimum picture quality so that you get the best picture automatically. While the VCR is turned on, the CVC indication \ is always displayed to show that the Crystal View Control is activated. 21-pin Scart Socket The 21-pin Scart socket transmits both input and output signals for picture and sound.
Page 189
PLAY STOP SEARCH S7511 VEQ11L07B S7512 VEQ11L07B S7515 VEQ11L07B MARK INDICATES THE PRIMARY CIRCUIT TO DISTINGUISH THE PRIMARY FROM CAUTION THE SECONDARY CIRCUIT. PAY ATTENTION NOT TO RECEIVE AN ELECTRIC SHOCK DURING REPAIR AND SERVICE OF THE PRODUCTS. S7513 VEQ11L07B S7514 VEQ11L07B T1101 P1103...
Page 190
VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE VIDEO MAIN SIGNAL PATH IN REC MODE CAPSTAN SERVO PHASE LOOP CAPSTAN SERVO SPEED LOOP CYLINDER SERVO PHASE LOOP CYLINDER SERVO SPEED LOOP P1501 C2536 0.1 IC7504 LOADING M(-) LOADING M(-) LOADING M(+) RN5VD28AA LOADING M(+) IC2502...
Page 191
SYSTEM CONTROL & SERVO ICs DC VOLTAGE CHART (SP MODE) REF.NO. IC2502 IC7503 PIN.NO. S-VHS ET CH SAT CVC VCR XP EP LP SP ON OFF PNA4611M02VT REMAIN STOP 14.3 14.6 14.3 1.1 13.9 DP7501 VSL0533 PLAY 13.9 13.9 14.3 1.1 13.9 14.5 13.5 14.3 1.1 13.9...