Page 1
ORDER NO. VRD0102004C2 Video Cassette Recorder NV-FJ614EG / NV-FJ613EL / NV-FJ613EGY / NV-FJ613EC / NV-FJ613ECM / NV-FJ613ECN / NV-FJ613ECY Z-MECHANISM SPECIFICATIONS 2001 Matsushita Electric Industrial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law.
/ Please refer to the service manual for Z- Mechanism Chassis. (Order No. VRD9802005C2) 2. The Model No. is indicated on the Schematic Diagram and Circuit Board Diagrams as follows. Model No. Indication Mark NV-FJ614EG, NV-FJ613EL NV-FJ613EGY NV-FJ613EC/ECM/ECN NV-FJ613ECY 2. GENERAL DESCRIPTIONS 2.1. SERVICE CAUTION 2.1.1.
Page 3
STEP2.INPUT THE MODEL & OPTION CODE 1. Set up the applicable model code and option code by ordering the following table. PROCEDURE F.I.P. DISPLAY Turn on the Service Mode 1.Press the FF key and the EJECT key simultaneously for more than 3 seconds. Activate the Service Mode 2 2.While keep placing FF key, press the EJECT key in twice.
Page 5
2. UPPER CYLINDER DISASSEMBLY A. Remove 2 screws (A). B. Remove the Cylinder Stator Unit. C. Remove 2 screws (B). D. Remove the Cylinder Rotor Unit. E. Loose Hex screw (C) (1.5 mm) and remove the CYLINDER RETAINER. F. Remove the Upper Cylinder. Fig.
Page 6
3. UPPER CYLINDER ASSEMBLY When reassembling, perform the steps in the reverse order. Notes: 1. Install the Cylinder Retainer so that the 2 holes on top of the Cylinder Retainer are at right angles with the P3502 Connection. 2. Tighten the Hex screw (C) (1.5 mm) while pressing down on top of the Cylinder Retainer.
Page 7
3. Install the Cylinder Rotor Unit so that the inner hole of the Cylinder Rotor Unit fits to the small projection (D) on top of the Upper Cylinder. 4. Tighten 2 screws (B). Fig. S6 5. install the Cylinder Stator Unit. 6.
(PAL: VFJ8125H3F) and adjust it if necessary. 2.1.3. CHECKING OF MAIN C.B.A. When servicing the MAIN C.B.A., take out the MAIN C.B.A. and mechanism from the frame and turn over. Fig. S8 2.1.4. FLAT CARD CABLE INSTALLATION When installing the Flat Card Cable on the connector, install the Flat Card Cable with the cable contacts facing the connector contacts.
Page 9
2.3. INTRODUCTION OF VIDEO HEAD CLEANING CASSETTE / (POLISHING TYPE) 1. We are pleased to introduce Panasonic Video Head Cleaning Cassette, VFK0923FT [for service purposes] and VFK0923FSE [ for end users] for all VHS/SVHS VCP and VCR. 2. These cleaning cassettes are exclusive removing the hard and sticky clogging on video heads.
Page 10
VFK0923FT (For Service usage) Type of Cassette Full VHS Cassette Cleaning Time 10 Seconds/Time Tape Length 20 m Usability in a Path 180 Times VFK0823FSE (For end users) Type of Cassette Full VHS Cassette Cleaning Time 10 Seconds/Time Tape Length 3.34 m Usability in a Path 30 Times...
VFK0823FSE (For end users) Note: The tape material itself is the same in both types. 2.4. SELF-DIAGNOSIS RESULT DISPLAY The "SELF-DIAGNOSIS RESULT DISPLAY & MEMORY function is built in this VTR. It means that when the VCR detects undesirable condition, it can be displayed a “Error code (Two numbers from the left)”...
INDICATION CAUSE REMEDY/CHECK After cylinder lock is detected, the cylinder Check the cylinder motor drive circuit. does not start rotating again even after tape unloading. Cassette tape is not wound up during the tape Check the capstan motor drive circuit. unloading except EJECT mode.
3.1.2. DETAIL OF DISASSEMBLY METHOD 1. REMOVAL OF THE TOP PANEL Remove 4 Screws (A) Fig.D2 2. REMOVAL OF THE FRONT PANEL UNIT Unlock 7 Tabs (B) Fig. D3...
3. REMOVAL OF THE MECHANISM UNIT Remove Screw (C) Remove 3 Screws (D) Remove 2 screw (E) Note: 1. Keep pressing 2 stoppers on Cassette Holder Plate and Press Cassette Holder Plate to the rear. 2. Remove the Mechanism Unit after bend the Cylinder Shield in the direction of the arrow.
Remove 4 screws (F) Unlock 4 Tabs (G) Fig. D5 NOTE: Before mounting the MAIN C.B.A. onto the frame, be sure to confirm that the insulation sheet is mounted on the frame as shown in Fig. D6. Fig. D6 5. SERVICING POSITION Fig.
Page 16
3.2. MECHANICAL ADJUSTMENT PROCEDURES Refer to the Service Manual for Z-Mechanism Chassis. / (Order No. VRD9802005C2) 3.3. ELECTRICAL ADJUSTMENT PROCEDURES 3.3.1. TEST EQUIPMENT The following equipments are required for Electrical Adjustments. 1. Dual-Trace Oscilloscope - Voltage Range: 0.005-5V/div - Frequency Range: DC-35MHz - Probes: 10:1 / 1:1 2.
Page 17
1. TAPE SPEED: SP 2. CHANNEL: AV1/AV2 (Set to signal input terminal number) 3.3.3. ADJUSTMENTS ITEM ADJ. MODE INPUT TAPE M. EQ. SPEC. REMARKS PLAYBACK --- Refer to procedure ALIGNMENT SHIFTER / PG SHIFTER TAPE / ADJUSTMENT ADJUSTMENT as (PAL) in Fig.E3.
Page 18
PROCEDURES FIP DISPLAY Press the FF and EJECT Keys simultaneously for 3 seconds. Press the FF and EJECT Keys simultaneously twice. Press the EJECT key for 3 seconds. Press the CH UP key once. Insert the Alignment cassette tape. (PAL:VFJ8125H3F) When the sequence of the automatical adjustment has been terminated, the following action has been made.
Page 19
PROCEDURES FIP DISPLAY Press the FF and EJECT Keys simultaneously for 3 seconds. Press the FF and EJECT Keys simultaneously twice. Press the EJECT key for 3 seconds. Press the CH UP key in 3 times. Insert the blank cassette tape. (The adjustment is automatically started.) When the sequence of the automatical adjustment...
Page 20
PROCEDURES FIP DISPLAY Connect the Oscilloscope to: *CH1..Video Out (TW3002). *CH2..V.FREQ.(TW6002) Press the "4" key on the remote controller. (Confirm that TW6002 becomes high(5V)). Adjust the Frequency response by pressing the "2"(increase) and/or "8"(decrease) key on the Remote Controller. (See Fig.E2) Store the Adjusted value by pressing the "5"...
11. REPLACEMENT PARTS LIST 11.1. CHASSIS PARTS SECTION PARTS LIST...
Page 26
Ref. No. Part No. Part Name & Description Remarks VEG1522 CYLINDER UNIT [SUPPLIED FROM MBV] VXP2001 UPPER CYLINDER UNIT [SUPPLIED FROM MBV] VDB1256 CYLINDER RETAINER VEM0715 CYLINDER MOTOR UNIT VXS0135 EARTH BRUSH UNIT VMD3795 FLAT CABLE HOLDER [SUPPLIED FROM MBV] VEK9069 CAPSTAN UNIT L1AZ00000004...
WASHER VMX3022 WASHER 11.2. CASING PARTS SECTION PARTS LIST Ref. No. Part No. Part Name & Description Remarks VGM1748 TOP PANEL [SUPPLIED FROM MBV]NV-FJ614EG- K,NV-FJ613EGYK/EL-K VGM1733 TOP PANEL [SUPPLIED FROM MBV]NV-FJ613EL-S/ EC-S/ECMS/ECNS/ECYS VYP8025 FRONT PANEL UNIT [SUPPLIED FROM MBV]NV-FJ614EG-K VYP8201...
Ref. No. Part No. Part Name & Description Remarks VQT9009 OPERATING INSTRUCTIONS(DANISH) [SUPPLIED FROM MBV]NV- FJ613ECNS/ECYS N2QAKB000001 REMOTE CONTROLLER [SUPPLIED FROM MBV]NV-FJ614EG-K N2QAKB000001 R0186-720010 BATTERY COVER [SUPPLIED FROM MBV]NV-FJ614EG-K N2QAHB000007 REMOTE CONTROLLER [SUPPLIED FROM MBV]NV-FJ613EL-S/ EL-K/EGYK/EC-S/ECMS/ECNS/ECYS N2QAHB000007 R0185-720010 BATTERY COVER...
Page 30
Ref. No. Part No. Part Name & Description Remarks VEP06D85K MAIN C.B.A. (RTL)[SUPPLIED FROM MBV]NV- FJ614EG-K,NV-FJ613EL-S/EL-K THE FOLLOWING C.B.A.S ARE INCLUDED IN MAIN C.B.A. VEP07A16A,VEP07A23L VEP06E00G MAIN C.B.A. (RTL)[SUPPLIED FROM MBV]NV- FJ613EGYK THE FOLLOWING C.B.A.S ARE INCLUDED IN MAIN C.B.A. VEP07A16A,VEP07A23L VEP06D85L MAIN C.B.A.
Page 48
R0206 (FG HEAD) R0212 R0213 Q0203 P0201 Q0202 IC0201 R0207 CURR LIMIT (CAPSTAN MOTOR DRIVE) HOLE HOLE CAP ET SENSOR SENSOR CAP ED/S RCC SET CAP FG1 Q0201 GND (FG) R0210 C0201 REG 5V GND (MOTOR) D0203 TL0204 TL0202 TL0203 LOAD MOTOR (-) LOAD MOTOR (+) TL0201...
Page 49
CYLINDER SERVO SPEED LOOP P2901 MAIN COIL 2 MAIN COIL 3 HALL IC GND (CYL) MAIN COIL 1 NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST.
Page 51
AUDIO MAIN SIGNAL PATH IN REC MODE AUDIO MAIN SIGNAL PATH IN PLAYBACK MODE :TO POWER SUPPLY/RF SECTION :TO SYSTEM CONTROL & SERVO SECTION :TO LUMINANCE & CHROMINANCE/AUDIO SECTION L4503 R4523 1.2u 4700 :TO INPUT/OUTPUT SECTION :TO TIMER SECTION C4524 C4525 R4521 C4522...
Page 52
VIDEO MAIN SIGNAL PATH IN REC MODE VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE AUDIO MAIN SIGNAL PATH IN REC MODE AUDIO MAIN SIGNAL PATH IN PLAYBACK MODE :TO POWER SUPPLY/RF SECTION :TO SYSTEM CONTROL & SERVO SECTION :TO LUMINANCE & CHROMINANCE/AUDIO SECTION L4903 :TO Hi-Fi AUDIO SECTION R4945...
Page 54
R :TO POWER SUPPLY/RF SECTION THE STRIPED FRAME INDICATES THE PRIMARY CIRCUIT TO DISTINGUISH THE PRIMARY CAUTION T :TO TIMER SECTION FROM THE SECONDARY CIRCUIT. PAY ATTENTION NOT TO RECEIVE AN ELECTRIC SHOCK DURING REPAIR AND SERVICE OF THE PRODUCTS. T1101 ETE28K131AZ LB1102...
Page 55
VIDEO MAIN SIGNAL PATH IN REC MODE AUDIO MAIN SIGNAL PATH IN REC MODE VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE AUDIO MAIN SIGNAL PATH IN PLAYBACK MODE :TO POWER TRANSFORMER SECTION :TO SYSTEM CONTROL & SERVO SECTION TU7601 Q1002 Q1006 :TO LUMINANCE &...
Page 60
VIDEO MAIN SIGNAL PATH IN REC MODE VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE AUDIO MAIN SIGNAL PATH IN REC MODE AUDIO MAIN SIGNAL PATH IN PLAYBACK MODE R :TO POWER SUPPLY/RF SECTION :TO SYSTEM CONTROL & SERVO SECTION :TO Hi-Fi AUDIO SECTION IC3501 AN3368SB :TO INPUT/OUTPUT SECTION...
Page 69
SYSTEM CONTROL & SERVO ICs DC VOLTAGE CHART (SP MODE) IC1501 IC1502 Ref. No. MODE STOP PLAY IC2501 Ref. No. MODE STOP 16.8 16.8 16.8 16.8 PLAY 14.9 14.9 15.2 14.9 15.1 15.1 15.4 15.1 14.4 14.4 14.6 14.7 14.3 14.3 14.6 14.9...
Page 70
No. Port Name Description P-OFF P-Save P-FAIL Reset CURRENT_LIMIT O Capstan motor current limit terminal. F ADJUST O Analogue voltage output for HEAD frequency response adjustment N.C. -- Low fix (No Connection.) Terminal of the Current emphasis video/FM audio recording current. [HIFI/2HEAD ]:Fix to Low (Normal mode) C EMPHA(H) [4HEAD]...
Page 71
No. Port Name Description P-OFF P-Save P-FAIL Reset ROTARY.SW O Output terminal for rotary switch. H.A.SW O Output terminal for HEAD AMP switch. ENVE.SELECT I Input terminal for enverope selection. VIDEO.H.SW O Output terminal for video HEAD switch. A.H.SW O Output terminal for FM audio HEAD switch. Audio Mute output terminal for tuner and decoder.
Page 72
No. Port Name Description P-OFF P-Save P-FAIL Reset LC.OSC OUT O The oscillation output terminal for OSD dot clock. RESET(L) I Input terminal for microprocessor reset. 4FC.LPF I 4fc clock input terminal OSD.FSC IN I OSD clock input terminal 5V(OSD) I 5V input terminal CVIN I Input terminal for Composite video signal.
Page 73
No. Port Name Description P-OFF P-Save P-FAIL Reset FLD/T2 DATA OUT O Serial data output terminal for FIP driver and TEST_2(Factory use). Not fix Low FLD_CS O Chip select terminal for FIP driver. Not fix Low T.REEL.PULSE I Input terminal for Take-up Reel sensor pulse. S.REEL.PULSE I Input terminal for Supply Reel sensor pulse.
Page 74
INPUT CONDITION VIDEO OUTPUT RESULT AUDIO OUTPUT RESULT POWER INPUT RF (C) AV1 Out AV2 Out SELECT ON(H) PB(H) PB(H) PB(H) Selector Selector AV2 In AV1 In AV2 In AV1 In Mute AV2 In AV1 In AV2 In AV1 In AV2 In AV1 In Mute...
Page 75
INPUT CONDITION VIDEO OUTPUT RESULT AUDIO OUTPUT RESULT POWER INPUT RF (C) AV1 Out AV2 Out SELECT ON(H) PB(H) PB(H) PB(H) Selector Selector P.ON NO.TU VCR out VCR out INSEL C+.TU VCR out VCR out INSEL VCR out VCR out AV1 In AV1 In AV1 In...
Page 76
INPUT CONDITION VIDEO OUTPUT RESULT AUDIO OUTPUT RESULT POWER INPUT RF (C) AV1 Out AV2 Out SELECT ON(H) PB(H) PB(H) PB(H) Selector Selector P.ON DECODER VTR NO.TU VCR out AV1 In AV1 In AV1 In VCR out AV1 In AV1 In AV1 In C+.TU VCR out TUN IN...
Page 77
4.43 NTSC L BILINGUAL 443NT [L] BILINGUAL L A. COMP BIL [L] AUDIO COMPONENT SIGNAL BILINGUAL H BIL. [H] A. COMPO AUDIO COMPONENT SIGNAL BILINGUAL L AUDIO DUBBING PAUSE L BIL/M1 [L] A. D.P [L] AUDIO DUBBING PAUSE L BS CLOCK A.
Page 78
CYL GND CYLINDER GND FULL. E. 12V FULL ERASE 12V DELAIED FM RECORDING H D.F.M. REC [H] GND (ANALOG) GND [A] DELAIED FM RECORDING L D. FM REC [L] GND (TUNER) GND [TU] D. GND GND/NON SW 12V DIGITAL GND GND/N.
Page 79
POWER OFF H LINE IN [R] LINE INPUT (R) P-OFF [H] POWER OFF L LINE OUT [L] LINE OUTPUT (L) P-OFF [L] LINE OUT [R] LINE OUTPUT (R) P. FAIL POWER FAILURE DETECT LP H POWER OFF H LP [H] P.
Page 80
SYSTEM CONTROL 5V RF OUT RF OUTPUT SYSCON 5V SYSTEM SW RF Y RF LUMINANCE SIGNAL SYSTEM TAKE-UP PHOTO TRANSISTOR RF. Y. IN RF LUMINANCE SIGNAL INPUT T-PHOTO TAKE-UP REEL PULSE RF. Y. OUT RF LUMINANCE SIGNAL OUTPUT T-RL. PLS TIMER BUS CLOCK ROTAR.
Page 81
MAIN SIGNAL PATH IN REC MODE MAIN SIGNAL PATH IN PLAYBACK MODE IC4501 JK4903 (AV1) TW4907 SYS IIC CLOCK TO/FROM QR4502 IIC BUS SYSTEM INTERFACE CONTROL AUDIO OUT (R) MUTE SYS IIC DATA TW4903 AUDIO IN (R) QR4501 AUDIO OUT (L) MUTE TW4902 AUDIO IN (L)
Page 82
IC6001 CAPSTAN IC7501 IC0201 (CAPSTAN MOTOR DRIVE) (SYSTEM CONTROL/SERVO IC) DP7501 MOTOR TL2503 L0201 TL0201 MOTOR DIFFERENTIAL TORQUE P0201 P2501 CURRENT DRIVE AMPRIFIER CONTROL LIMIT TIMER DISPLAY 20MHz IN CAPSTAN P0201 P2501 ERROR TORQUE X6002 20MHz OUT POSITION CAPSTAN TORQUE P0201 P2501 SIGNAL...
Page 83
MAIN SIGNAL PATH IN REC MODE MAIN SIGNAL PATH IN PLAYBACK MODE Y/C VIDEO OUT TO/FROM SYSTEM (C/D) CONTROL VIDEO OUT IC4901 Q4904 SYSTEM C SYNC CONTROL TO TUNER RFC VIDEO OUT CLAMP FROM TV TUNER VIDEO CLAMP DEMODULATOR JK4903 (A/B) (AV1) PB +12V...
Page 84
IC3001 QR3502 QR3501 PEAKING H-TRAP NLDE DOUB IC3501 PICT DELAY TW3030 AMP & H.AMP FAMI CLP1 P3502 LP L REC-Y FAMI TO/FROM P3502 CYLINDER LP COM VIDEO HEAD MAIN PREAMP P3502 LP R FAMI & H.SW TW3001 H.AMP CLIP L-TRAP &HPF MAIN SYNC...