Table of Contents
Advertisement
Quick Links
Installation Instructions
30" Freestanding Sealed Burner Gas Range
WARNING
Tip Over Hazard
A child or adult can tip the range and
be killed.
Connect anti-tip bracket to rear
range foot.
Reconnect the anti-tip bracket, if the
range is moved.
Failure to follow these instructions can
result in death or serious burns to
children and adults.
IMPORTANT:
Read and save these instructions.
IMPORTANT:
Installer: Leave Installation
Instructions with the homeowner.
Homeowner: Keep Installation
Instructions for future reference.
Read and save these instructions
for local electrical inspector's use.
with self-cleaning oven
Write down the model and serial
numbers before installing range.
Both numbers are listed on the
model/serial rating plate located on the
oven frame behind the storage drawer
panel.
Model # _______________________________
Serial # _______________________________
Quick Reference
Table of Contents:
Pages
Before you start
2
Electrical requirements
3
Gas supply requirements
4
Product dimensions
5
Cabinet dimensions/requirements
5
6 - 9
Installation steps
Gas conversions
10 - 11
If range does not operate
12
If you need assistance/service
12
Moving the range
12
9758660
9758660
www.whirlpool.com
1
Part No. 9758660
Advertisement
Table of Contents
Related Manuals for Whirlpool 9758660
Summary of Contents for Whirlpool 9758660
- Page 1 Instructions with the homeowner. model/serial rating plate located on the Homeowner: Keep Installation oven frame behind the storage drawer Instructions for future reference. panel. Read and save these instructions Model # _______________________________ for local electrical inspector’s use. Serial # _______________________________ Part No. 9758660...
-
Page 2: Before You Start
Before you start... It is the customer’s responsibility: Your safety and the safety of WARNING: If the • To contact a qualified electrical installer. others are very important. information in this manual • To assure that the electrical installation We have provided many important safety is not followed exactly, is adequate and in conformance with messages in this manual and on your... -
Page 3: Electrical Requirements
Tools needed: Materials needed: Parts supplied: Assemble the required tools and parts • gas line shutoff valve before starting installation. Read and • 1/2" male pipe thread nipple for connection Not shown: follow the instructions provided with any to pressure regulator •... -
Page 4: Gas Supply Requirements
Gas supply requirements Observe all governing codes and Rigid pipe WARNING ordinances. connection: Requires a This installation must conform with local combination of codes and ordinances. In the absence of pipe fittings to local codes, installations must conform obtain an in-line connection to the range. with American National Standard, All strains must be removed from the National Fuel Gas Code ANSI Z223.1 —... -
Page 5: Product Dimensions
Product dimensions Grounded electrical outlet is required. See “Electrical requirements. ” Proper gas supply connection must be available. See “Gas supply requirements. ” 27-1/8” (68.9 cm) depth with handle 36" (91.4 cm) cooktop height 46-7/8" (119.1 cm) overall height 25" (63.5 cm) 29-7/8"... - Page 6 Now start... Contact a qualified floor covering WARNING installer for the best procedure for Make sure the anti-tip bracket is drilling mounting holes through your installed: type floor covering. Excessive Weight Hazard • Look for the anti-tip bracket securely attached to floor. Use two or more people to move and install range.
- Page 7 Gas and electrical connections Apply pipe-joint compound made Use 5/16" combination wrench Test all connections by for use with L.P . gas to the smaller thread and channel lock pliers to attach the brushing on an approved non-corrosive ends of the flexible connector adapters. flexible connector to the adapters.
-
Page 8: Check Operation
Check operation Electronic ignition system If flame needs to be adjusted, turn You can check the burner flame by control knob to the “LOW” setting and removing the flame spreader or by using Cooktop and oven burners use electronic remove control knob. Insert a small flat- a mirror. - Page 9 If your oven has electronic If oven flame needs to be adjusted: If your oven has electronic Locate the air shutter next to the controls: controls: pressure regulator. Loosen screw and 1. Press the “BAKE” pad. 1. Press the “CUSTOM BROIL ” pad. adjust the air shutter until the proper flame appears.
-
Page 10: Gas Conversions
Gas conversions Gas conversions (from Natural gas to L.P . pressure regulator L.P . Gas gas; or from L.P . gas to Natural gas) must Surface Propane rate Orifice Color be done by a qualified installer. burner (BTU/hr) Number Marking Left 8,000 Green/... -
Page 11: Natural Gas Conversion
Reinstall the storage drawer. Surface burners: Remove burner Oven burner: Use 1/2" combination Complete installation steps 9 through 24. caps. Use a Phillips or Quadrex wrench to loosen the orifice hood away Checking for proper cooktop burner and screwdriver to remove the two screws from pin (approximately 2 to 2-1/2 turns). -
Page 12: Moving The Range
8. Reconnect gas line to range and children and adults. check for leaks. 9. Plug in range or reconnect power. 10. Reinstall storage drawer. Part No. 9758660 Printed in U.S.A © 2004 Whirlpool Corporation Benton Harbor, Michigan 49022 2/2004...